Contact Us

TPS562203DRLR

Brand: Texas Instruments
Texas Instruments TPS562203DRLR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS562203DRLR — Power Management & Signal Chain | Superb Automation

TPS562203DRLR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS562203DRLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS562203DRLR: 2 A synchronous buck, 4.2 V to 17 V input, 600 kHz, Eco-mode, SOT-563

TPS562203DRLR is a 2 A synchronous step-down converter in the same 1.6 mm by 1.6 mm six pin body as its 3 A sibling, running at a fixed 600 kHz from a 4.2 V to 17 V input in a SOT-563 body of 6 pins. The switch resistances are the same as the 3 A member, 100 milliohm on the high side and 55 milliohm on the low side at 25 degrees, so the difference between the two parts is the current rating and the current limit rather than the silicon. Control is D-CAP3 with no external compensation, the soft start is fixed at 1.4 ms, and the part starts into a prebiased output. In Eco-mode the no load current is 110 microamp and the shutdown current is 7 microamp.

Order code and package

TPS562203DRLRActive, SOT-5X3 (DRL) body, 6 pins, 4000 pieces on a large reel, Sn finish, marking 2203
TPS562203DRLR.AActive, the same body and reel, with the material row printed at MSL Level-1-260C-UNLIM
TPS562206DRLRActive, the forced continuous conduction member, same body, same reel, marking 2206
TPS563203DRLRActive, the 3 A member of the family in the same body, marking T203
Temperature rangeminus 40 to 125 degrees junction on every published row

Electrical parameters that decide the application

Input voltage4.2 V to 17 V
Output voltage0.6 V to 7 V, set by a divider into the FB pin
Output current2 A continuous, with both switches integrated
Switch resistance100 milliohm high side, 55 milliohm low side at 25 degrees
Switching frequency600 kHz fixed, 100 ns minimum off time, 55 ns minimum on time
Feedback voltage600 mV nominal, 588 to 612 mV over minus 40 to 125 degrees
Valley current limit2.5 A minimum, 3.9 A typical, 4.8 A maximum
Quiescent and shutdown110 microamp no load in Eco-mode, 7 microamp with EN low

Family variants and how they differ

TPS562203Eco-mode at light load, the string on this page
TPS562206forced continuous conduction, same 2 A rating and same body
TPS563203the 3 A member, same switch resistances and same 600 kHz
Soft start1.4 ms fixed, no external capacitor needed
Maximum duty cycleabout 95 per cent, which sets the input floor for a given output

Points to check before this part goes on a BOM

Two and a half amps is the minimum valley limit on a 2 A part. The published window is 2.5 A minimum, 3.9 A typical and 4.8 A maximum, which is the same typical and maximum as the 3 A member with a lower floor. The valley limit watches the low side switch current rather than the load current, so a 2 A load with ripple on top does not trip it, and a load that steps to 3 A for a few milliseconds may not trip it either. A sustained 3 A load will.

The 2 A and 3 A strings share their switches, so a substitution is safe in one direction. Fitting the 3 A part where a 2 A part was specified leaves the same footprint, the same divider and the same inductor, with a higher current limit and a higher rating. Fitting the 2 A part where the 3 A part was specified is not safe: the valley limit floor drops to 2.5 A and a genuine 3 A load will sit in current limit. The board does not tell the two apart, so the reel label is the only control.

Seventeen volts covers a twelve volt bus and stops well short of twenty four. The input range starts at 4.2 V, so a 5 V rail at minus ten per cent is inside it and a 3.3 V rail is not. At the top, a 24 V bus is above the rating before any tolerance is applied, and the part should not be offered for a 24 V industrial board no matter how small the load.

Ninety five per cent maximum duty sets the headroom, and it is easy to get wrong. A 3.3 V output from a 4.2 V input needs 79 per cent at DC and more once the switch and inductor losses are added, so it is tight but inside the limit. A 5 V output from a 5 V rail is impossible, and a 3.3 V output from a 3.6 V battery is at the edge. The duty limit, not the current limit, is what rejects those boards.

The 1.4 ms soft start and the prebias capability answer two different problems. The fixed ramp keeps a moderate output capacitor from looking like a short at power up. The prebias support stops the converter from pulling down a rail that is already charged, which happens when a standby supply holds the output up while the main converter is off. A board that replaces this part with one that lacks prebias support will reset the circuit it was trying to keep alive.

At 600 kHz the inductor is the largest passive on the board. A 1 to 2.2 microhenry inductor keeps the ripple current inside a sensible fraction of the 2 A load, and its saturation current has to clear the peak, which is the load plus half the ripple. The valley limit protects the switch, not the inductor: a small inductor that saturates before the current limit is reached will produce a current spike the comparator never sees in time.

Eco-mode ripple is a real constraint on an analogue rail. At light load the converter skips pulses and the output ripple becomes a low frequency sawtooth rather than a 600 kHz triangle. A 3.3 V rail that feeds an ADC or a radio can pick that up as noise in the measurement band. Where the rail is analogue, the forced continuous member holds the frequency at every load and trades light load efficiency for a clean spectrum.

The six pin body relies on the copper under it for heat. From 12 V to 3.3 V at 2 A the conduction loss comes to about 0.27 W, roughly a third of what the 3 A member dissipates at 3 A from 12 V to 5 V, so the 2 A part runs with real margin in the same footprint. That margin disappears on a two layer board with a narrow trace under the part, which is why the copper is part of the specification and not a detail.

Two active rows share one marking, and the moisture statement differs. The base row and the .A row both carry 2203, and one of them is printed at MSL Level-1-260C-UNLIM. Level 1 means no bake clock and no floor life tracking, which simplifies the line. A broker reel with an unreadable label loses that, and the part is small enough that a mixed reel is not detectable by eye.

Four thousand pieces on a large reel changes how a small order is packed. A prototype build of a few hundred pieces comes as a broken reel with cut tape, and the cut end is where moisture and bent leads appear. For repair demand it is worth asking for the reel count and the taping condition on the offer, because a 4000 piece reel is not always what a service centre can store or handle.

What to confirm before this part goes on a purchase order

Confirm the load current the board actually draws, not only the part number. The 2 A and 3 A strings are pin compatible and look identical on a reel, and a 3 A board fitted with the 2 A part works on the bench and fails in the field when the load reaches its rating.

Ask for the marking, the date code and the country of origin, and state the reel size on the offer. Because both rows carry 2203, the packing list and the reel label are the only record of which material revision ships, and for an automotive or medical customer that record is part of the file.

Where this order code fits

It runs a 3.3 V rail at 2 A from a 12 V adapter in a set top box, a broadband gateway or a building controller, where the load never reaches the 3 A that the larger member of the family covers. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

Is it pin compatible with the 3 A TPS563203? Yes. Same six pin SOT-563 body, same pinout, same 600 kHz and same 600 mV reference. The difference is the current rating and the valley limit floor, so the 3 A part can replace this one but not the other way round on a board that really draws 3 A.

Can it run from a 5 V rail? Yes, for a 3.3 V output. The input range starts at 4.2 V, and a 5 V rail at minus ten per cent is 4.5 V, which leaves the duty cycle at about 66 per cent. A 5 V output from the same 5 V rail is not possible because the maximum duty cycle is about 95 per cent.

What is the difference from the TPS562206? Only the light load behaviour. This part skips pulses in Eco-mode for high efficiency below a few hundred milliamp; the 206 keeps switching at 600 kHz at every load and holds a narrow ripple spectrum. Footprint, divider and inductor are the same.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the OEM Procurement page sets out the checks that keep a substitute from failing on the bench.