TPS562200DDCR
Product Specifications
TPS562200DDCR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS562200DDCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS562200DDCR: 4.5 V to 17 V input, 2 A synchronous step-down, D-CAP2, SOT-23-6
TPS562200DDCR is a synchronous step-down converter rated 2 A that runs from 4.5 V to 17 V with a fixed 650 kHz switching frequency and no external compensation in a SOT-23 body of 6 pins. The part is the 2 A member of a two part family, with 122 milliohm and 72 milliohm switches inside a 1.6 mm by 2.9 mm body. The D-CAP2 loop closes inside the package and works with ceramic output capacitors, so a 2 A rail can be built with an inductor, two capacitors and two feedback resistors and nothing else.
Order code and package
| TPS562200DDCR | Active, SOT-23-THIN, 3000 pieces on a large reel, Sn finish, MSL-1-260C unlimited floor life, marking 200 |
| TPS562200DDCT | Active, 250 pieces on a small reel, the same body |
| TPS563200 | the 3 A member of the same family, 68 milliohm and 39 milliohm switches |
| Package size | 1.6 mm by 2.9 mm including pins, six pin SOT-23 thin |
| Ambient range | minus 40 to 85 degrees, which is an ambient rating and not a junction rating |
Electrical parameters that decide the application
| Input voltage | 4.5 V to 17 V |
| Output current | 2 A continuous |
| Output voltage | 0.76 V to 7 V, set by an external divider |
| Switching frequency | 650 kHz fixed |
| Feedback accuracy | 1 per cent at 25 degrees |
| Soft start | 1 ms fixed, internal |
| Shutdown current | less than 10 microamp |
| Protection | cycle by cycle current limit, hiccup undervoltage, non latching overvoltage, undervoltage lockout, thermal shutdown |
Family variants and how they differ
| TPS562200 | 2 A, the string on this page |
| TPS563200 | 3 A in the same body and pinout, for boards that need headroom |
| D-CAP2 control | adaptive on time, no compensation network, stable with ceramic capacitors |
| Eco-mode | pulse skipping at light load, entered and left automatically |
| Pre-biased start | the output can come up with a charge already on it without discharging it |
Points to check before this part goes on a BOM
One per cent at 25 degrees is not one per cent over temperature. The feedback specification is quoted at room temperature only. Over the full ambient range the window widens, so a rail that has to hold 1.8 V within one per cent at 85 degrees needs the error budget calculated rather than read from the feature list. The parts in this family that quote a wider figure do so for a reason.
The 85 degree figure is ambient, not junction. That distinction decides whether the part survives in a sealed enclosure. A 2 A load at 12 V in and 1.2 V out dissipates about 0.6 W in the switches and the inductor, and in a small package that is a junction rise of tens of degrees above the ambient. A box at 70 degrees internal is already close to the limit before any margin is applied.
D-CAP2 removes the compensation pin and adds a constraint. There is nothing to tune, which is why the part count is so low. The constraint is that the output capacitor has to sit inside the range the internal loop was characterised for. A very large ceramic bank, added to reduce ripple after a failed emissions test, can push the loop into a slow ringing response on a load step.
A one millisecond soft start is fast. It limits the inrush into the output capacitor, but a 470 microfarad bank charged in 1 ms draws well over the rated current and the part will current limit at power up. That is normally harmless because the limit is cycle by cycle, but a board with a large bank and a weak input supply can sit in hiccup until the input recovers.
Eco-mode is the default and it changes the ripple at light load. At light load the converter skips pulses, which raises efficiency and also raises the output ripple and moves the switching spectrum. If the 1.2 V rail feeds an analogue block, or if the board is being scanned for emissions at 10 per cent load, the light load behaviour matters and the output filter has to be chosen for it.
The marking is the only visible difference from the 3 A part. TPS562200 and TPS563200 share a package, a pinout and a family name, and the top marking is a short code that is easy to misread on a reel. A 3 A part in place of a 2 A part is usually harmless, but the reverse leaves a board that browns out under a load it was built for, and the failure looks like a firmware problem.
Seventeen volts is the ceiling, and a 12 V rail is close to it. A 12 V adapter with ten per cent tolerance reaches 13.2 V, which is fine. A 12 V rail that carries an inductive load can spike well above 17 V, and the absolute maximum is only a few volts higher, so a transient suppressor at the input is worth the space on an industrial board.
The feedback divider is the whole output setting. There is no internal divider and no fixed voltage option in this family, so a board that changes its rail from 1.8 V to 1.2 V changes two resistors. That flexibility is why the same part appears on several boards, and it is also why a reel cannot be assigned to a rail without the resistor values being known.
Pre-biased start is more useful than it sounds. On a board where a second converter or a leaking load holds the output up before the enable arrives, the part starts without pulling the output down first. That avoids a glitch on a rail that another device is already using and can be the difference between a clean power up and a reset loop.
What to confirm before this part goes on a purchase order
State the input bus and the output voltage with the load current, because the same string is used at 1.2 V, 1.8 V and 3.3 V with different inductors and dividers. A substitute offered against the part number alone cannot be checked for ripple or thermal margin.
Ask for the reel label and the marking, and confirm whether the order needs the 2 A or the 3 A member. For repair quantities the small reel is the practical choice, but the body is published on a 3000 piece large reel, so a short quantity means a broken reel that has to be agreed in writing.
Where this order code fits
It makes a 2 A rail at 1.2 V or 1.8 V for a set top box or a home gateway, from a 12 V adapter, with ceramic output capacitors and no compensation network. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Can it deliver 2 A at 85 degrees ambient? The current rating is electrical. At 85 degrees ambient the junction rise from the switch losses has to be added, and the thermal shutdown sits not far above that. A board that must deliver 2 A continuously in a hot enclosure needs a copper area under the part and a check of the junction temperature, not just the headline current.
Does it need an external bootstrap capacitor? Yes, one small capacitor between the switch node and the boost pin. It is the only part of the gate drive that lives outside the package, and it is also the part that is most often left off a copied board.
What happens at light load? The converter enters eco-mode and skips pulses. Efficiency stays high, the output ripple grows, and the switching spectrum moves. For a digital load that is fine; for an analogue load the output capacitor has to be chosen for the skip mode ripple.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.