TPS56121DQPR 25+
Product Specifications
TPS56121DQPR 25+
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS56121DQPR 25+ from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS56121DQPR: a 15 A synchronous buck with the FETs in the package
TPS56121DQPR is a high current synchronous step-down converter that takes 4.5 V to 14 V in and delivers up to 15 A at an output as low as 0.6 V. The FETs are integrated as a Power Block, so the switching pair, the driver and the control sit in one 22-pin PQFN measuring 6 mm by 5 mm with a thermal pad. It is aimed at point of load rails on telecom and networking boards, where a 12 V bus has to become a 1 V or 1.2 V core rail at high current inside a small area.
The control scheme is voltage mode with input feed-forward, which responds to a change in the input voltage within the same switching cycle rather than waiting for the loop to integrate the error. On a board where the 12 V bus is shared with other loads and moves when they switch, that behaviour keeps the output steady without a second feedback path.
The numbers below come from SLUSAH4D, revised February 2016, and from the orderable addendum in the same document.
What the order code sits on
| Function | synchronous step-down converter with integrated Power Block FETs |
| Input range | 4.5 V to 14 V |
| Output current | up to 15 A |
| Output voltage | down to 0.6 V, set by an external divider |
| Reference | 600 mV with 1 percent accuracy |
| Switching frequency | fixed options of 300 kHz, 500 kHz and 1 MHz |
| Control | voltage mode with input feed-forward |
| Current sense | high-side and low-side FET on resistance |
| Overcurrent | programmed by a resistor at ILIM, calibrated at power on, shutdown and restart until the fault clears |
| Soft start | programmable with an external capacitor |
| Pre-biased output | supported |
| Protection | thermal shutdown |
| Package | PQFN DQP, 22 pins, 6.00 mm by 5.00 mm with PowerPAD |
| Reel | 2500 pieces on a large reel, moisture level 2 |
| RoHS row | printed as RoHS Exempt on the addendum |
Current sensing through the FET resistance
Sensing the current across the on resistance of the FET removes the shunt and its loss, and it also makes the limit drift with temperature, because the on resistance of a silicon FET rises by roughly a third between 25 and 125 degrees. The device handles this by calibrating at power on: it measures the voltage at the ILIM pin during the initial sequence, stores an internal reference, and compares the FET drop against that reference while running. The calibration removes the initial spread of the internal current source, but it cannot remove the temperature drift that happens after start-up.
The practical result is that a limit set for 20 A at room temperature may be 15 A at high temperature, or the other way round depending on how the calibration was done. A board that must guarantee 15 A at 85 degrees has to set the limit with margin and check it hot, and a board that is protecting the inductor only needs the limit to sit below the saturation current at the highest temperature the board will see.
The high-side and low-side sensing are both available, which is what makes the scheme work at very small duty cycles. At 12 V in and 1 V out the high side is on for less than a tenth of the period, too short for a clean peak measurement, while the low side is on for the rest of the cycle and its current is the inductor current. The device uses the low side for the running limit and the high side as the fast protection.
Feed-forward and the 12 V bus
Input feed-forward makes the ramp slope proportional to the input voltage, so a step on the input produces an immediate change in duty cycle rather than a slow correction through the error amplifier. On a telecom board where several converters share a 12 V bus, a load step on one converter moves the bus, and every other converter sees it. Feed-forward keeps the other rails from moving with it.
The same behaviour makes the loop easier to stabilize across the input range, because the gain from input voltage to output is reduced. A board that runs from 4.5 V to 14 V has a three to one change in input, and without feed-forward the loop gain would change by the same factor.
Soft start and the inrush into a core rail
The soft start capacitor sets the ramp, and the ramp is what keeps the inrush into the output capacitance inside the current limit. A 1 V core rail with several thousand microfarads of decoupling, which is normal on a board with a large processor, needs a ramp long enough that the charging current stays below the limit at the lowest input voltage, where the current available is smallest.
Starting into a pre-biased output matters when the core rail is held up by another path, for example by a second converter or by a leakage path through the processor. The device does not discharge the rail before starting, and the ramp begins from the level it finds.
Thermal behaviour at 15 A
Fifteen amps through the integrated FETs is the headline, and the headline is only reachable with the thermal pad soldered to a copper area that can spread the loss. At 1 V out and 12 V in the duty cycle is short, so the high-side conduction loss is small and the low-side conduction loss dominates; at 5 V out the two are closer to equal. The package is 6 mm by 5 mm with the pad on the underside, and the vendor land pattern includes vias into an inner copper layer for exactly this reason.
The 125 degree operating limit on the reel row is an ambient figure for the package, and a board inside a rack with restricted airflow can reach it while the inlet air is far cooler. A board that puts the inductor next to the part without copper between them, or that keeps the thermal pad on a narrow neck, will derate the current well below 15 A.
Carriers and what the addendum prints
| TPS56121DQPR | LSON-CLIP DQP, 22 pins, 2500 pieces on a large reel, active |
| TPS56121DQPT | same body, 250 pieces on a small reel |
| RoHS | printed as RoHS Exempt rather than Yes |
| Lead finish | NIPDAU or tin, depending on the row |
| Moisture level | Level-2-260C-1 YEAR |
| Operating temperature | minus 40 to plus 125 degrees |
| Body size | 6.00 mm by 5.00 mm including the thermal pad |
The RoHS column is the line a compliance team will ask about. Exempt is not the same as compliant: it means the part relies on an exemption in the directive, and a customer whose own declaration says compliant may need the exemption reference before they can accept the part. That is worth settling before a production order rather than at the audit.
The small reel row exists, so a prototype build can buy 250 parts. The large reel holds 2500, which is the quantity to quote for a production run and the one that appears on the addendum for this string.
Where a 15 A single phase converter fits
A point of load rail on a line card, a 12 V to 1.2 V core supply on a networking board, and a 5 V to 1 V rail on an industrial controller are the classic sockets. Above 15 A the single phase part runs out of current and a multiphase controller with external FETs takes over, which is a different board with a different control scheme.
When a customer is replacing a converter that has gone obsolete, the comparison usually turns on the current rating, the frequency and the way the current limit is programmed. A part with the same pinout but a different sensing scheme will not accept the same ILIM resistor, and the limit will be wrong on the first article. Our power management cross reference page covers the rows we compare, and the obsolete part cross reference hub covers the case where the original family has been discontinued.
Questions buyers ask before a first order
Is the switching frequency adjustable? No. The part is offered in three fixed frequency options, and the option is chosen by the order code rather than by a resistor. A board that needs a different frequency needs a different string.
How is the current limit set? A resistor from ILIM to ground, read during the power-on calibration. Changing the resistor changes the limit, and changing the inductor usually requires changing the resistor with it.
Can the output go below 0.6 V? No. The reference is 600 mV and the output is set by a divider from it, so 0.6 V is the floor unless an external reference is added, which this part does not support.
Does the part need an external diode? No, the synchronous low-side FET carries the freewheeling current. That is what allows the 15 A rating in a package this size without a diode to dissipate in.