TPS561201DDCR
Product Specifications
TPS561201DDCR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS561201DDCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS561201DDCR: 4.5 V to 17 V, 1 A synchronous buck in SOT-23
TPS561201DDCR is a synchronous buck converter with both FETs and the loop inside a six pin package in a SOT-23 body of 6 pins. It makes a 1 A rail from 4.5 V to 17 V with two resistors, two capacitors and an inductor, and it skips pulses at light load instead of staying in continuous conduction.
Order code and package
| Order code | TPS561201DDCR, DDC package, 3000 pieces on a reel |
| Body | SOT-23, 1.60 mm by 2.90 mm, six pins |
| Switch resistance | 140 mOhm high side and 84 mOhm low side |
| Light load | Pulse skip, the TPS561208 is the continuous conduction version |
| Reference | 0.8 V at 2 per cent at 25 C |
Electrical parameters that decide the application
| Input range | 4.5 V to 17 V |
| Output range | 0.76 V to 7 V at 1 A |
| Control | D-CAP2, stable with ceramic output capacitors and no compensation parts |
| Frequency | 580 kHz fixed |
| Soft start | 1.0 ms fixed |
| Shutdown current | Under 10 uA with the enable pin low |
| Protection | Cycle by cycle overcurrent with hiccup, non latching undervoltage and thermal shutdown |
Family variants and how they differ
| TPS561208 | Same part in continuous conduction mode, for a rail that must not change frequency at light load |
| TPS561201 | Pulse skip mode, better efficiency at a few milliamps |
| DDC body | Six pin SOT-23, the smallest option in this band |
| EN pin | A divider on the enable pin sets a system UVLO above the internal threshold |
| VFB pin | Two resistors set the output from 0.76 V to 7 V |
Points to check before this part goes on a BOM
The 17 V input limit is what separates this part from the 28 V and 42 V converters in the same catalogue. A 12 V adapter rail with a 20 per cent transient reaches 14.4 V and fits, while a 15 V rail does not, and a 19 V notebook adapter is outside the part entirely.
Conduction loss at 1 A is small enough that switching loss dominates. At 12 V to 3.3 V the duty is 27 per cent, so the high side FET dissipates 0.035 W and the low side 0.063 W, and the 580 kHz switching loss in a SOT-23 body is of the same order. That is why the efficiency curve falls at 12 V input and flattens at 5 V.
Pulse skipping at light load is the reason the part exists in a standby product. At 1 mA the converter stops for long periods and the quiescent current, not the switching, sets the draw. A rail that feeds an always on microcontroller benefits, and a rail that feeds an ADC does not, which is what the TPS561208 is for.
A 7 V output from a 4.5 V input is not possible, and the data sheet range is the union of all operating points rather than one converter. At 580 kHz and 4.5 V in, a 7 V output is a boost, so the real limit is the input minus the dropout, and a 5 V rail from a 5 V input is already outside the part.
The 2 per cent feedback accuracy at 25 C is a room temperature figure on a 0.8 V reference, which is 16 mV. Over temperature and with 1 per cent divider resistors the rail can sit 4 per cent off before any load regulation, which is why a 1.2 V core rail usually wants a part with a tighter reference.
D-CAP2 without a compensation network still depends on the output capacitor. A 22 uF ceramic is stable and fast; a 470 uF electrolytic with high ESR is stable and slow; a 100 uF ceramic with very low ESR can put the loop into a double pole that the internal ramp was not written for, and the data sheet values are the starting point.
The 1 ms soft start is fixed and short. A 100 uF output charged to 3.3 V in 1 ms needs 0.33 A of capacitor current, which is inside the 1 A rating with the load, but a 470 uF bank needs 1.55 A and trips the current limit into hiccup. A board with a large output bank needs a different part, not a larger inductor.
The six pin body has no separate ground for the power and signal return, so the input capacitor and the output capacitor have to meet at one point under the part. A star ground on a two layer board is the difference between a 20 mV output ripple and a 100 mV one with a spike on it.
The 580 kHz frequency with a 2.2 uH inductor gives about 0.5 A of ripple at 1 A, which is 50 per cent and at the top of what the loop wants. Going to 4.7 uH halves the ripple and slows the transient, and the choice is usually made by the output capacitor rather than by the inductor: a 22 uF ceramic with 4.7 uH is a calmer rail than 10 uF with 2.2 uH.
The enable pin is not a logic input with a wide margin. It is rated to the input voltage and its threshold is a fraction of the rail, so a divider from a 12 V input that puts 5 V on the pin at the wrong moment is outside the absolute maximum. The divider sets the system UVLO and also protects the pin, and both jobs have to be checked.
A 1 A converter in a six pin SOT-23 has no thermal pad, so the heat leaves through the pins and the copper they sit on. At 12 V to 3.3 V and 1 A the part dissipates about 0.1 W, which is 12 C of rise at 120 C/W, and the same part at 17 V to 1.2 V dissipates 0.2 W and reaches 24 C. The board copper is the difference between a part that runs cool and one that shuts down in a hot enclosure.
Where this order code fits
The part suits a set top box, a monitor, a router or a small industrial board that needs 1 A at 3.3 V, 1.8 V or 1.2 V from a 5 V or 12 V rail and has no room for a controller plus two FETs. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.
Questions buyers ask
What is the difference from the TPS561208? The 201 skips pulses at light load for efficiency, the 208 stays in continuous conduction for a constant frequency and a cleaner spectrum.
Can it make 5 V from 5 V? No. The output has to stay below the input by the dropout of the high side FET and the inductor resistance, so a 5 V to 5 V rail needs a different topology.
Does it need a bootstrap capacitor? Yes, one from VBST to SW, and it is the only part the high side driver needs.
How much output capacitance is sensible? 22 uF to 100 uF of ceramic for a 1 A rail. Above that the fixed 1 ms soft start runs into the current limit at start up.
Is the enable pin 5 V tolerant? It is rated to the input rail, so on a 12 V input it is a 12 V pin. A 3.3 V logic signal drives it through a divider or directly, but a 12 V divider has to be checked against the threshold, not against a 5 V assumption.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.