TPS560200DBVR
Product Specifications
TPS560200DBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS560200DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS560200DBVR: 4.5 V to 17 V input, 500 mA synchronous step-down, 600 kHz, SOT-23-5
TPS560200DBVR is a synchronous step-down converter rated 500 mA with the switches integrated, a 600 kHz fixed frequency and an internal 0.8 V reference in a SOT-23 body of 5 pins. The five pin body has no compensation pin and no bootstrap pin brought out, so the whole converter is an inductor, two capacitors and two resistors. It is aimed at housekeeping rails: the standby supply in a set top box, the logic rail in a modem, and any place where a linear regulator would waste too much heat but a 3 A converter would be oversized.
Order code and package
| TPS560200DBVR | Active, SOT-23-5, 3000 pieces on a large reel, NIPDAU finish, MSL-1-260C unlimited floor life, marking L562 |
| TPS560200DBVRG4 | Active, the same body and reel with the Green material declaration |
| TPS560200DBVT | Active, 250 pieces on a small reel |
| Package size | 2.9 mm by 1.6 mm, five pins, no thermal pad |
| Temperature range | minus 40 to 125 degrees junction on the published rows |
Electrical parameters that decide the application
| Input voltage | 4.5 V to 17 V |
| Output current | 500 mA continuous |
| Output voltage | 0.8 V to 6.5 V, set by an external divider |
| Switch resistance | 0.95 ohm high side, 0.33 ohm low side |
| Switching frequency | 600 kHz fixed |
| Reference accuracy | plus or minus 1.3 per cent over temperature |
| Soft start | 2 ms internal |
| Junction temperature | minus 40 to 125 degrees, thermal shutdown above that |
Family variants and how they differ
| TPS560200 | 500 mA, the string on this page |
| TPS562200 | the 2 A member of the wider family in a different body |
| D-CAP2 control | adaptive on time with no external compensation |
| Eco-mode | automatic pulse skipping at light load |
| Pre-biased start | the output can already have a charge on it at power up |
Points to check before this part goes on a BOM
Nine hundred and fifty milliohm is a high side resistance. At 500 mA the conduction loss in the high side switch alone is about a quarter of a watt, and the low side adds more during the off time. That is why the part is a 500 mA device and not a 1 A device in the same body, and why the efficiency at 12 V in and 3.3 V out sits in the mid eighties rather than the nineties.
Five pins means no bootstrap capacitor and no compensation network. The gate drive is internal and the loop is fixed, which is what allows a five pin body. The trade is that the output capacitor has to be inside the characterised range and the inductor cannot be pushed far from the recommended value without checking the loop. A board that replaces the recommended inductor with a much larger one to cut ripple current will move the crossover frequency and can show a slow oscillation on a load step that looks like a thermal problem.
The 1.3 per cent reference is over temperature, which is unusual at this size. A 0.8 V reference that holds 1.3 per cent across the range makes the part usable as a logic rail with a tight tolerance, not only as a housekeeping supply. It also means a 1.2 V output from a 0.8 V reference is set by a divider ratio of 1.5, which is a comfortable place to be.
A two millisecond soft start is gentle for a 500 mA part. It limits the inrush into the output capacitor without making the rail visibly slow. A large capacitor bank charged in 2 ms draws more than 500 mA, and the part will limit the current rather than fail, so a board with a 100 microfarad bank takes slightly longer than 2 ms to come up.
Six hundred kilohertz is a compromise frequency. It is high enough for a small inductor and low enough to keep the switching loss down at 17 V in. At 600 kHz the inductor for 500 mA is a few microhenry, and the output capacitor is a single 10 or 22 microfarad ceramic.
The input range covers a 12 V adapter with margin. A 12 V rail with ten per cent tolerance reaches 13.2 V, well inside the 17 V ceiling. A 15 V rail is also inside. A 19 V laptop adapter is not, and that is a common mistake when a board is repurposed from a 12 V board to a 19 V supply. The input capacitor voltage rating and the inductor saturation current both have to be rechecked on that move, since neither is set by the converter part number. None of those three checks appears on a datasheet curve, so they have to be made on the board.
Eco-mode changes the light load ripple, and this part is used at light load. A housekeeping rail that draws 20 mA most of the time sits in eco-mode, where the output ripple is larger and the switching frequency drops. For a digital load that is irrelevant; for a rail that feeds a low noise amplifier or a reference it is the dominant ripple source.
Thermal shutdown is the only protection on a short. There is no hiccup mode and no latch, so a hard short at the output pulls the current limit until the junction temperature trips the thermal shutdown, the part cools, and it restarts. The board survives, but the behaviour in a fault is a slow thermal cycle, not a clean foldback. A board that has to ride through a shorted load without that cycle needs a current limited switch in series, or a fuse sized below the converter current limit.
The marking L562 identifies the string. The body is small and the marking is the only visible field, so an incoming inspection that relies on the label alone cannot tell a 500 mA part from a lookalike in the same body. For a repair order it is worth asking the supplier for the reel label and the date code together.
What to confirm before this part goes on a purchase order
State the input bus and the output voltage. A 19 V adapter is outside the 17 V rating and that mistake is common when a board is moved from a 12 V supply to a laptop brick.
Ask for the marking and the date code, and confirm the reel size. The string is published on a 3000 piece large reel, so a 500 piece repair order means a broken reel, and the packaging and the date code have to be agreed on the offer before shipment.
Where this order code fits
It supplies a 500 mA housekeeping rail in a modem or a set top box from a 12 V adapter, where the standby current and the five pin body are the reason for choosing it. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the How to Reduce Component Cost page.
Questions buyers ask
Can it run from 24 V? No. The input ceiling is 17 V, and the absolute maximum is only a little above that. A 24 V bus needs a different part in the same family or a pre regulator.
Is an external bootstrap capacitor needed? No. The five pin body has no bootstrap pin; the gate drive is generated inside the package. That is one of the reasons the part count is so low.
What is the maximum output voltage? 6.5 V, set by the divider from the 0.8 V reference. Above that the part cannot regulate because the internal reference and the duty cycle limit are reached.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Vendor Consolidation page sets out the checks that keep a substitute from failing on the bench.