Contact Us

TPS55288RPMR

Brand: Texas Instruments
Texas Instruments TPS55288RPMR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS55288RPMR — Power Management & Signal Chain | Superb Automation

TPS55288RPMR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS55288RPMR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS55288RPMR: 36 V, 16 A four switch buck boost converter with I2C

TPS55288RPMR is a synchronous four switch buck boost converter that regulates above or below the input in a VQFN-HR body of 26 pins. It holds an output between 0.8 V and 22 V from a 2.7 V to 36 V input, and every setting that matters is written over I2C rather than fixed by resistors.

Order code and package

Order codeTPS55288RPMR, RPM package, 3000 pieces on a reel
BodyHotRod VQFN, 4.00 mm by 3.50 mm
TopologyFour switch buck boost, two 16 A FETs in the boost leg
InterfaceI2C for voltage, current limit, frequency, mode and spread spectrum
Soft startFixed 4 ms

Electrical parameters that decide the application

Input range2.7 V to 36 V
Output range0.8 V to 22 V in 20 mV steps, 1 per cent reference accuracy
Output current limitUp to 6.35 A in 50 mA steps, 5 per cent monitoring accuracy
Inductor current limitAverage limit programmable up to 16 A
Frequency200 kHz to 2.2 MHz set by a resistor, synchronisable to an external clock
Light loadPFM or forced PWM selectable over I2C
Efficiency97 per cent at 12 V in, 20 V out and 3 A
ProtectionOutput overvoltage, hiccup on a sustained short, thermal shutdown, cycle by cycle peak limit

Family variants and how they differ

Buck modeInput above output, the boost leg stops switching and the part behaves as a buck
Boost modeInput below output, the buck leg passes through and the boost leg regulates
Buck boost regionInput close to output, all four switches run and the loop blends the two modes
Spread spectrumOptional, reduces peak emissions at the cost of a wider noise floor
Current senseAn optional resistor between ISP and ISN sets the output current limit

Points to check before this part goes on a BOM

This is a true four switch buck boost, so the output can be either side of the input without a mode change. That matters for a battery product where a 3 cell pack runs from 9 V to 12.6 V and the rail has to stay at 12 V: the part bucks at the top of the charge and boosts at the bottom, and the handover happens without a glitch because the loop blends the two.

The 6.35 A output current limit and the 16 A inductor limit are different limits, and the difference is the point. At 20 V out the 6.35 A limit is 127 W, while at 5 V out the same current limit is 32 W and the inductor limit is never reached. The register that matters depends on the output voltage, not on the load current alone.

Efficiency of 97 per cent at 12 V to 20 V and 3 A is a 1.86 W loss. In a 4 mm by 3.5 mm package that loss has to leave through the pads, and the boost leg FETs are the parts that carry it, so the copper under the part is part of the thermal budget and not a detail of the assembly drawing.

The 100 W claim from a 12 V input means 8.3 A in at unity efficiency and about 9.1 A at 92 per cent. The input connector, the input capacitor ripple current and the inductor saturation all have to be specified for that current, and a board sized on the 6.35 A output limit is 40 per cent short on the input side.

Fixed 4 ms soft start is a compromise. It is long enough to keep the inrush into a few hundred microfarads modest, and short enough that a USB PD sink sees the rail within the specification window. A load with 2000 uF of input capacitance needs the current limit raised rather than the ramp lengthened, because the ramp is not programmable.

I2C control is a procurement issue as much as an engineering one. The rail behaviour lives in firmware, so a board revision can change the output voltage without a component change, and a replacement part has to match the register map, not just the pin out. Two parts with the same body size and different register maps are not substitutes.

The buck boost region is where the loop is least comfortable. With the input within a few hundred millivolts of the output, the part switches between modes on a cycle by cycle basis and the ripple in the inductor current grows. The frequency has to be chosen so that the four switches have time to change state, and 2.2 MHz is the wrong end of the range for a 12 V to 12 V conversion.

Output overvoltage protection and the hiccup mode are separate. A transient that pushes the output above the OVP threshold stops switching until the voltage falls, while a sustained short makes the part retry at a low duty cycle. A load that sees the rail dip during hiccup has to tolerate it, and that is a system level decision rather than a converter one.

The register map is part of the part number. Output voltage, current limit, frequency and light load mode all live in I2C registers, and a substitute with the same body and pin out but a different map will program to the wrong rail. Procurement has to match the exact order code and the firmware has to know which revision it is talking to, which is a different kind of second source problem than a pin compatible analog part.

Spread spectrum reduces peak emissions by a few decibels and moves the energy into a wider band. That is what gets a product through an emissions test, and it is also what makes a low noise rail slightly noisier at every frequency. A converter feeding an RF block should have the feature off, and the same board feeding a digital load should have it on.

The inductor carries the full input current in boost mode and the full output current in buck mode, so its saturation rating has to cover the larger of the two plus the ripple. At 12 V to 20 V and 6.35 A out the input current is 10.6 A plus half the ripple, and an inductor rated at 10 A saturates in the middle of a load step rather than at its rated current.

Where this order code fits

The part suits a USB PD power bank or charger port, a battery powered instrument that has to hold a fixed rail across the charge range, and any board where the same converter has to work from an adapter and from a battery. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

Can the output be higher than 22 V? No, 22 V is the programmed maximum and 36 V is the input maximum. A 24 V rail is outside the part.

Does it need an external current sense resistor? Only if the output current limit has to be enforced. Tying ISP and ISN to the output disables that function and leaves the inductor limit active.

Is the frequency fixed? No, one resistor sets 200 kHz to 2.2 MHz, and an external clock can drive it if the board has one.

What happens when the input equals the output? The part enters the buck boost region and runs all four switches, which is the least efficient operating point but keeps the output in regulation.

Does it need firmware to start? The part starts with its default register values, so it produces a rail without I2C. Firmware then changes voltage, limit and mode, and a board that relies on the defaults gets the default rail, not the intended one.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.