TPS552872QWRYQRQ1
Product Specifications
TPS552872QWRYQRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS552872QWRYQRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS552872QWRYQRQ1: automotive 36 V four switch buck-boost converter
TPS552872QWRYQRQ1 is a synchronous buck-boost stage that holds a regulated rail while the input moves above, through and below the output in a VQFN-HR (RYQ) body of 21 pins. It integrates all four switches, takes 3.0 V to 36 V in and delivers 0.8 V to 22 V out at up to 4 A, which covers a 12 V automotive rail that has to survive a cold crank and a load dump. Output current is monitored to plus or minus 5 percent, and the switching frequency is set from 200 kHz to 2.2 MHz or synchronised to an external clock.
Order code and package
| Order code read out | TPS552872 QW RYQ R Q1: device TPS552872, QW automotive grade, RYQ twenty one pin VQFN-HR, R large tape and reel, Q1 qualified |
| Package | VQFN-HR (RYQ), 21 pins, thermally enhanced with the pads under the body |
| Carrier in the vendor addendum | TPS552872QWRYQRQ1 at 3000 pieces on a large reel |
| Moisture level | Level 2, 260 degrees, one year floor life |
| Lead finish | Nickel palladium gold |
| Qualification | AEC-Q100 grade 1, minus 40 to plus 125 degrees ambient |
| Absolute maximum | 42 V on the input and the first switch node, 25 V on the output side pins, 150 degrees junction |
Electrical parameters that decide the application
| Input voltage range | 3.0 V to 36 V, with undervoltage lockout at 2.9 V rising and 2.65 V falling |
| Output voltage range | 0.8 V to 22 V, programmable, with plus or minus 1 percent reference accuracy |
| Output current | 4 A, with the vendor quoting 30 W from a 12 V input and 25 W from a 9 V input in boost mode |
| Switching frequency | 200 kHz to 2.2 MHz set by one resistor, or synchronised to an external clock |
| Control scheme | Average current mode, which behaves predictably as the input crosses the output voltage |
| Output current monitor | Plus or minus 5 percent accuracy, which is what allows a load to be limited in software |
| Output overvoltage | 22.5 V minimum, 23.5 V typical, 24.5 V maximum, with 1 V of hysteresis |
| Internal bias | 5.2 V regulator, 5.05 to 5.45 V at a 50 mA load |
| Quiescent current | 760 uA typical into the input pin while enabled without switching |
| Shutdown current | 0.8 uA typical with the device disabled, which matters for a parked vehicle |
| Enable and UVLO | 1.23 V typical threshold with 10 mV of hysteresis on the enable pin |
| Emissions | Optional spread spectrum, and the package is laid out to keep the two switch node loops short |
Family and order code decode
| Q1 suffix | AEC-Q100 qualified, grade 1 ambient range, which is the automotive grade requirement |
| QW prefix in the string | the automotive device family marker, placed between the base part number and the package |
| RYQ body | 21 pin VQFN-HR with the thermal pads underneath, 3000 pieces on a large reel |
| Lower current members | the family includes smaller current versions in the same control scheme, for rails that do not need 4 A |
| Without the Q1 suffix | a non automotive part with the same function exists for industrial use, and the two should not be mixed on one bill of materials |
Points to check before this part goes on a BOM
A four switch buck-boost is the right topology for an automotive rail because the input crosses the output in normal operation. A 12 V battery sits at 13.5 V while charging, drops to 6 V during a cold crank and can rise above 20 V during a load dump event, so a stage that has to produce a 12 V or 15 V rail cannot be a plain buck or a plain boost. The two pairs of switches hand over around the crossover point, and average current mode keeps that handover from producing a visible step in the output.
The 3.0 V input floor matters for cold crank. A vehicle that cranks at minus 30 degrees can pull the battery below 6 V for tens of milliseconds, and a converter that drops out at 8 V resets the electronics that are supposed to stay alive. A 3.0 V operating floor with lockout at 2.65 V keeps a downstream rail in regulation through that window, which is what the start stop and telematics functions need.
Output current monitoring to plus or minus 5 percent is a system feature rather than a measurement nicety. It lets a controller limit a USB port, a sensor heater or a motor pre-drive in software without a separate shunt amplifier, and the accuracy is good enough to distinguish a normal load from a fault. The monitor is a voltage proportional to the current, so the scaling resistor sets the range.
Frequency choice in a vehicle is constrained from both ends. Below about 400 kHz the inductor and the output capacitor grow beyond what a small module can hold, and above 2 MHz the switching loss in a 36 V device becomes hard to remove from a sealed housing. The 2.2 MHz ceiling also allows the converter to sit above the AM band, and the spread spectrum option smears the remaining harmonics so a scan of the harness does not show a comb of peaks.
The 0.8 uA shutdown current is quoted with the enable pin low and no load, and it is the figure that decides whether a module can be left connected to the battery permanently. The 760 uA quiescent current in the enabled state is twenty times larger, so a parked vehicle that keeps the rail alive pays for it. The usual arrangement is to hold the converter off and enable it from the body controller, which is why the enable threshold is specified separately from the UVLO.
Where this order code fits
Used in automotive and industrial rails that must hold regulation across a wide input: infotainment and cluster supplies, telematics units, camera and sensor modules, USB charging ports, LED drivers and any body controller that has to ride through start stop and cold crank. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Does it regulate when the input equals the output? Yes. The four switch topology hands over between buck and boost around the crossover point, and average current mode control keeps the transition smooth. That region is where a two switch converter would either drop out or run at 100 percent duty.
What is the difference between this and the industrial version? The Q1 suffix. This part is AEC-Q100 grade 1 qualified for minus 40 to plus 125 degrees ambient. The industrial part has the same function with a narrower qualification, so the two should not be interchanged on an automotive bill of materials.
How is the output current monitor used? It produces a voltage proportional to the output current with plus or minus 5 percent accuracy, which a controller can read to limit a port or detect a fault. It removes the need for a separate current sense amplifier.
What sets the switching frequency? One resistor from the frequency pin, from 200 kHz to 2.2 MHz, or an external clock through the sync pin. The spread spectrum option is enabled separately and is worth using when the harness emission scan is tight.
Which reel size is published? 3000 pieces on a large reel for the RYQ body, which is the only carrier row for this order code. A prototype build normally comes from a broken reel.
What happens during a load dump? The input is rated 42 V absolute maximum and the converter stops switching above its overvoltage protection, so a load dump event is survived by the input rating rather than by regulation. The upstream protection still has to clamp the transient inside that window.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.