TPS55165QPWPRQ1
Product Specifications
TPS55165QPWPRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS55165QPWPRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS55165QPWPRQ1: a 36 V, 1 A single inductor buck boost that keeps a 5 V or 12 V rail alive through the cranking dip
TPS55165QPWPRQ1 is an AEC-Q100 grade 1 synchronous buck boost converter with both bridges inside the package in a HTSSOP (PWP) body of 20 pins. It holds a fixed 5 V or 12 V output set by the state of the VOS_FB pin, runs at 2 MHz so the inductor stays small, delivers 1 A while the input is at 5.3 V or above and still gives 0.4 A with the input down at 2.3 V, and draws under 15 microamp in low power mode. The input window reaches 36 V, which is the load dump margin a 12 V automotive rail needs.
Order code and package
| TPS55165QPWPRQ1 | HTSSOP body of 20 pins with the PowerPAD, 2000 pieces on a large reel, nickel palladium gold finish, moisture level 3 at 260 C with 168 hours of floor life, marking TPS55165, active status in the addendum dated 9 November 2025 |
| TPS55165QPWPTQ1 | the same die in the same body on a 250 piece small reel, which is the string a pilot line orders before the reel quantity is settled |
| TPS55160QPWPRQ1 and TPS55162QPWPRQ1 | the adjustable members of the family, 5.7 V to 9 V set by a divider, with the same body and the same reel quantities |
| Body size | 6.50 mm by 4.40 mm, with the exposed pad as the only low impedance path from the die to the board copper |
| Temperature rows | ambient minus 40 C to 125 C on every row, while the junction tables run to 150 C, so the two figures are not interchangeable |
| Addendum alignment | the packaging table prints quantity on the row above the part number in several places, so the reel size is read from the R or T suffix as well as from the row |
Electrical parameters that decide the application
| Input voltage | 2 V to 36 V for a 5 V output, and 3.6 V to 36 V for the adjustable members, with the switch stopping above the overvoltage lockout |
| Output setting | a fixed 5 V with VOS_FB tied to ground and a fixed 12 V with VOS_FB tied to the internal VREG rail, so the same order code covers both rails without a divider |
| Output current | 1 A with the input at or above 5.3 V, 0.8 A above 3.8 V and 0.4 A above 2.3 V, which follows the current the inductor can carry as the duty cycle stretches |
| Low power current | 50 mA maximum in low power mode, which is the mode that keeps the quiescent draw under 15 microamp for a module that has to survive a parked vehicle |
| Switching frequency | 1860 kHz to 2140 kHz fixed, or 1800 kHz to 2400 kHz with spread spectrum enabled, both at 2 MHz nominal |
| Quiescent current | 0 to 15 microamp with a 12 V input, no load, low power mode and the part not switching, measured at 25 C junction |
| Shutdown current | 3 microamp with the ignition pin, the power latch and the power save pin all at zero volts |
| Switch resistance | 150 milliohm typical and 300 milliohm maximum on each of the four switches, buck high side, buck low side, boost high side and boost low side |
| Peak current limit | 2 A minimum, 3.5 A typical and 4.5 A maximum on the buck high side, the buck low side and the boost low side, which is a peak figure rather than a DC rating |
| Average coil limit | 2 A minimum and 2.8 A typical with a 4.7 microhenry inductor, and this is the number that governs a sustained overload rather than a transient |
| Undervoltage lockout | the converter turns off as the input falls through 1.8 V to 2 V, which is below the 2.3 V point where the 0.4 A output is still specified |
| Overvoltage lockout | switching stops at 36 V typical and the absolute maximum is 40 V, so a 36 V transient sits on the edge of the operating window |
| Startup condition | 5.3 V minimum at the input until the output passes the power good undervoltage threshold at 400 mA and a 22 microfarad output capacitor |
| Efficiency | up to 85 per cent, with the overlap control handing over between step down and step up without a mode command |
| Output ripple | 5 mV peak to peak at 1 A on the 5 V setting and 5 mV peak to peak at 0.8 A on the 12 V setting, both with a 47 microfarad output capacitor |
Family variants and how they differ
| TPS55165-Q1 | the fixed output member covered by this order code, 5 V with VOS_FB at ground and 12 V with VOS_FB at the internal VREG rail, 1 A from a 5.3 V input and 0.4 A from a 2.3 V input |
| TPS55162-Q1 | the adjustable member, 5.7 V to 9 V set by an external divider, with 300 mA at the low end of the input window and 600 mA once the input is within 1 V of the output |
| TPS55160-Q1 | the other adjustable member, same 5.7 V to 9 V window and the same current profile, with the low power mode and spread spectrum options available |
| Low power mode | selected on the PS pin, and it is what brings the quiescent current under 15 microamp, at the cost of a 50 mA ceiling on the output in that mode |
| Spread spectrum | selected on the SS_EN pin, moving the switching frequency from 2 MHz fixed to a 1800 kHz to 2400 kHz dither, which lowers the peak of a conducted emissions scan |
| Ignition latch | the part wakes on the IGN pin and holds itself on through IGN_PWRL, so a module can complete a shutdown after the key is removed |
| Qualification | AEC-Q100 grade 1 with grade 1 temperature classification, against the catalog members of the family which are not specified over the same ambient window |
Points to check before this part goes on a BOM
The ignition pin is a latch, not just an enable. The part wakes on the ignition input and then holds itself on through IGN_PWRL, so a module can finish a shutdown sequence after the key is turned off. A board that ties IGN_PWRL to the ignition line instead of to the microcontroller loses that behaviour.
The 1 A figure has three input conditions attached. 1 A needs 5.3 V or more at the input, 0.8 A needs 3.8 V and 0.4 A needs 2.3 V. A cranking profile that dips to 3 V is a 0.4 A case, and a load that draws 1 A there will drag the rail down rather than current limit cleanly.
The fixed 12 V setting comes from the VREG pin, not from a divider. Tying VOS_FB to VREG selects the 12 V option, so the accuracy of that rail is set inside the part and cannot be trimmed on the board. The 5 V option has the same property with VOS_FB at ground.
Spread spectrum is a pin choice on this order code. With the SS_EN pin left open the switching frequency is 2 MHz and with it connected the frequency dithers between 1800 kHz and 2400 kHz, which trades a little ripple for a lower peak in a conducted emissions scan.
Peak current limit is not the load rating. The 4.5 A maximum peak limit protects the switches, while the 2.8 A average coil limit decides how long an overload can run. A 1 A load with a large transient is fine, and a 1 A load with a shorted output is not.
The thermal pad is the whole thermal path. At 1 A from 12 V to 5 V the losses are inside the 20 pin body, and the exposed pad on a 6.50 mm by 4.40 mm footprint has to reach a copper area large enough for the junction to stay under 150 C.
What the cranking window means for the rest of the rail
A start stop vehicle drops the battery rail to about 3 V for tens of milliseconds and then recovers. This converter stays in regulation through that dip, but the current it can pass falls with the input, so the downstream load has to be either small or able to ride through on its own capacitance.
The 12 V output option is set for a rail that feeds a gate driver or an actuator, and the 5 V option is the usual logic rail. Because both come from the same die, a board can be built for either by changing one pin connection, which is why one order code covers two different products in a harness line.
Where this order code fits
an automotive body module, gateway or cluster supply that has to hold a 5 V rail through a cold crank and a 36 V load dump Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Does this part need a divider to set 12 V? No. VOS_FB tied to the internal VREG rail selects the fixed 12 V option and VOS_FB tied to ground selects 5 V. The adjustable members of the family, TPS55160-Q1 and TPS55162-Q1, are the ones that use a divider, and they cover 5.7 V to 9 V.
How much current is available during a cold crank at 3 V? 0.4 A, with the input at or above 2.3 V. The 1 A rating applies from 5.3 V up, and the 0.8 A rating from 3.8 V up, so the load has to be sized for the worst input in the profile rather than for the nominal battery.
Is the 36 V input rating a transient figure? The recommended operating range reaches 36 V and switching stops at that point by the overvoltage lockout, while the absolute maximum is 40 V. A load dump that goes beyond 40 V needs a front end clamp and not a bigger capacitor.
Is this the same die as the catalog TPS55165? The Q1 suffix is the automotive grade part, specified over minus 40 C to 125 C ambient with AEC-Q100 qualification and grade 1 temperature classification. The catalog part is not specified over the same ambient window.
What is the reel size? 2000 pieces on a large reel for the R suffix and 250 pieces on a small reel for the T suffix, with moisture level 3 at 260 C and 168 hours of floor life, so a partial reel has to be baked before a second reflow.
Can SUPERB supply this string against a production schedule? SUPERB quotes against the exact ordering string with date codes, packing and country of origin on the offer, and confirms whether the quantity ships from a large reel or a cut length before the order is placed.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.