Contact Us

TPS549B22RVFR

Brand: Texas Instruments
Texas Instruments TPS549B22RVFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS549B22RVFR — Power Management & Signal Chain | Superb Automation

TPS549B22RVFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS549B22RVFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS549B22RVFR 25 A PMBus buck with eight frequency settings and NVM backup

The TPS549B22RVFR sits between the 15 A and 40 A members of the family: 1.5 V to 18 V on PVIN, 4.5 V to 22 V on VDD, 25 A continuous, with 4.1 milliohm high side and 1.9 milliohm low side FETs in a 7 mm by 5 mm, 40 pin LQFN. The 25 A rating is the one most processor rails actually need, and the 4.1 and 1.9 milliohm figures are what keep the conduction loss in a range the package can pass to the board.

The PMBus interface runs at 1 MHz with packet error checking and an SMB_ALRT line, and it carries the standard VOUT_COMMAND and VOUT_MARGIN high and low commands. Selected settings can be backed up in NVM, so a board that loses its configuration returns to a known state at the next power up instead of to the factory default. That is the difference between a rail that is margined once at the factory and a rail that has to be reprogrammed after every power cycle.

Output voltage is 0.6 V to 5.5 V with the reference trimmed 0.6 V to 1.2 V in 50 mV steps by VSEL, at 0.5 per cent against 0.9 V nominal over 40 to 125 degrees junction. Eight switching frequencies are available over PMBus, from 315 kHz to 1.125 MHz, and the sense is a true differential pair.

Key parameters from the SNVSAU8A document

Input range1.5 V to 18 V on PVIN, 4.5 V to 22 V on VDD
Output current25 A continuous with 4.1 milliohm high side and 1.9 milliohm low side FETs
Output voltage0.6 V to 5.5 V, reference 0.6 V to 1.2 V in 50 mV steps by VSEL
Switching frequency315 kHz, 425 kHz, 550 kHz, 650 kHz, 825 kHz, 900 kHz, 1.025 MHz and 1.125 MHz over PMBus
Reference accuracy0.5 per cent against 0.9 V nominal over 40 to 125 degrees junction
Current limitRILIM resistor, temperature compensated, with an OC clamp behind it
Fault handlingHiccup or latch off selectable for overvoltage and undervoltage, VDD UVLO adjusted through the precision EN pin
Bus features1 MHz PMBus with packet error checking, SMB_ALRT, NVM backup for selected commands
Package40 pin LQFN-CLIP, 7 mm by 5 mm, RVF body, RoHS exempt

Why 25 A is the useful number

A 0.9 V core at 100 A is four 25 A phases or three 40 A phases, and the four phase option spreads the heat across more copper while keeping the inductor height low. On a 1U board where height is the binding constraint, 25 A per phase with four phases is often the only arrangement that fits under the lid. The 550 kHz setting exists in this part and not in the pin strapped sibling, and it is the setting that keeps the input ripple current out of a system clock band.

The trade against the 40 A part is board area against device count. Four 25 A devices need more pad area than three 40 A devices, but they also need smaller inductors each, and an inductor that fits under a lid is worth more than a device that does not.

Configuration, NVM and the production line

Three sources set the behaviour of the rail: the pin straps, the NVM contents, and the PMBus commands written at run time, in that order of precedence. A line that straps the board for one voltage and never writes the bus gets a stable rail. A line that writes the bus but does not store to NVM gets a rail that reverts on the next power cycle, which is the most common production surprise with this class of device.

Packet error checking and the alert line are there so a corrupted write is caught rather than silently applied. On a multi rail board with several converters on one bus segment, the alert line also tells the supervisor which device raised the flag.

Where this part fits

Processor and FPGA core rails, DDR rails, and multiphase point of load groups where four 25 A phases fit better than three 40 A phases. Our desk keeps the family cross reference and the NVM question on the checklist, see power management cross reference and one stop BOM sourcing.

What to check before a purchase order

RVF is the 40 pin 7 by 5 mm body and it is shared with the 40 A member, so a footprint check does not separate the two families. The order code letter does: TPS549B22 against TPS549D22 differs in current rating and in the reference range, and a mixed carton is possible when a distributor splits a family across reels. Ask for the reel label photograph on any first order of a family like this.

See date code management for how we segregate family members, and incoming inspection plan for the marking check we run on 40 pin bodies.

Questions that come up on this part

Is NVM the same as a configuration file on the host, is a common question. No, the NVM holds selected commands inside the device, and the host can still override them at run time. The second question is whether the 25 A part can drive a 40 A load with a bigger inductor. It cannot; valley current limit will trip on the first load step, and the failure looks like a control loop problem rather than a rating problem.