Contact Us

TPS549A20RVER

Brand: Texas Instruments
Texas Instruments TPS549A20RVER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS549A20RVER — Power Management & Signal Chain | Superb Automation

TPS549A20RVER

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS549A20RVER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS549A20RVER 15 A, 20 V input buck in a 4.5 mm by 3.5 mm package

The TPS549A20RVER is a 15 A synchronous buck with a 1.5 V to 20 V conversion input and a 4.5 V to 22 V bias input, in a 28 pin, 4.5 mm by 3.5 mm VQFN-CLIP. The 20 V PVIN is the highest in this family, which is what puts it on 12 V intermediate buses with a real transient allowance and on 18 V battery stacks. The power stage is 9.9 milliohm high side and 4.3 milliohm low side, with the boost switch integrated so no external bootstrap diode is needed.

Control is D-CAP3 with no external compensation, and the reference is 600 mV at 0.5 per cent from 40 to 85 degrees ambient. The PMBus interface is not there for telemetry alone: it sets the output margin, the soft start time, the power on delay, the VDD UVLO level, the fault reporting and the switching frequency, eight settings from 200 kHz to 1 MHz. A board can therefore be built once and tuned per program by bus write rather than by component change.

The device is specified from 40 to 125 degrees ambient, and the 15 A rating holds across the 1.5 V to 20 V PVIN window with the snubber arrangement the document describes. Above 15 V input the switch node ringing has to be managed, which is what the snubber note is about.

Key parameters from the SLUSC79A document

Input range1.5 V to 20 V on PVIN with the recommended snubber, 4.5 V to 22 V on VDD
Output current15 A continuous with 9.9 milliohm high side and 4.3 milliohm low side FETs
Output voltage0.6 V to 5.5 V against a 600 mV reference
Reference accuracy600 mV at 0.5 per cent from 40 to 85 degrees ambient
Switching frequencyEight settings from 200 kHz to 1 MHz, selected over PMBus
PMBus controlsOutput margin and adjustment, soft start time, power on delay, VDD UVLO level, fault reporting, frequency
ModesAuto skip Eco mode for light load, forced continuous conduction for tight ripple and fast transient
Package28 pin VQFN-CLIP, 4.5 mm by 3.5 mm, RVE body

What 20 V input costs and where it pays

Above about 14 V the switch node edge rate puts more energy into the board parasitics, and the document answers that with a snubber across the low side. A board that skips the snubber still works at 12 V and starts to show ringing at 18 V, which is exactly the condition a battery pack produces at full charge. For a board that has to hold 15 A at 18 V, the snubber is part of the bill, not an optional extra.

The payoff is margin. A 12 V bus with a 10 per cent transient reaches 13.2 V, and a converter rated to 20 V has room for the spike that follows a hot plug event. On telecom and industrial boards where the input can be switched at the connector, that headroom is what keeps field returns down.

PMBus without a full digital rail

The part still starts and regulates with no PMBus traffic, because the defaults are set internally. That means a contract assembly line with no bus master can build and test the board, and the customer can still margin the rail, change the soft start, or move the frequency in the rack. This is the middle ground between a pin strapped converter and a fully digital one, and it is what most 12 V to core rails actually need.

The fault reporting path uses the same bus, so a supervisor can read back what happened instead of guessing from a PGOOD line. On a board with several rails, that turns a field failure from a scope session into a log entry.

Where this part fits

Point of load rails on 12 V intermediate buses, telecom line cards, industrial controllers with an 18 V battery, and test equipment where the rail has to be margined during calibration. Our desk handles this class of part with the cross reference and the substitution checks ready, see power management cross reference and one stop BOM sourcing.

What to check before a purchase order

The RVE suffix is the 28 pin 4.5 by 3.5 mm body, and it is smaller than the 40 pin bodies used by the 25 A and 40 A members of the family, so a footprint drawn for one will not take the other. Confirm the VDD bias arrangement, because 20 V on PVIN with a 4.5 V VDD is the intended split, and a board that ties them together loses the low input capability. Then confirm the snubber is on the bill for any input above 15 V.

See pin to pin cross reference for the family comparison, and component lead time solutions when the small body is short.

Questions that come up on this part

Does the part need a bus master to start, is the usual first question. No, it starts on internal defaults and the bus is optional. The second is whether the frequency can be changed on the fly. It can be written while running, but the inductor and the output bank were chosen for one frequency, so a change at runtime is a test bench action rather than a production setting.