Contact Us

TPS54821RHLR

Brand: Texas Instruments
Texas Instruments TPS54821RHLR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS54821RHLR — Power Management & Signal Chain | Superb Automation

TPS54821RHLR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS54821RHLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS54821RHLR: a 4.5 V to 17 V, 8 A synchronous buck with hiccup in the 3.5 mm VQFN

TPS54821RHLR is an 8 A synchronous step down converter with current mode control in a VQFN (RHL) body of 14 pins. The RHL body is 3.50 mm by 3.50 mm with fourteen pins and an exposed thermal pad that the document requires to be soldered down. The split rail arrangement puts the control circuit on VIN and the power stage on PVIN, which is what allows PVIN to run as low as 1.6 V while VIN stays between 4.5 V and 17 V.

Order code and package

TPS54821RHLRVQFN (RHL), 14 pins, 3000 piece large reel, NIPDAU finish, MSL level 1 at 260 C, -40 to 125 C, marking 54821
TPS54821RHLTsame body on a 250 piece small reel, same finish and temperature row
TPS54821RHLRG4G4 suffix carried in the string, same RHL body and same 3000 piece large reel
Exposed padpin 15 on the package drawing, connected to ground and to the thermal path, and the document states it must be soldered for the part to work
Split railVIN supplies the control circuit from 4.5 V, PVIN supplies the power switches from 1.6 V, and the two can be tied together on a single rail
StatusActive, production; SLVSB14B, originally October 2011 and revised February 2016, with no errata attached

Electrical parameters that decide the application

Input and power stageVIN 4.5 V to 17 V, PVIN 1.6 V to 17 V, 20 V absolute maximum on both, 0.3 V maximum difference between ground and the exposed pad
Output current8 A from -40 to 125 C junction, 6 A if the junction is allowed to reach 150 C, which is the row that decides the derating
Reference0.6 V nominal, 0.594 V to 0.606 V over the full load range, which is the 1 percent the front page claims
Power FETs26 mOhm high side with 6 V of boot voltage and 19 mOhm low side at 12 V in, both specified at the pins
Current limitHigh side 10.5 A minimum, 14.5 A typical and 17 A maximum; low side sourcing 9.5 A to 15 A; low side sinking 2 A to 4 A
Hiccup timing512 cycles of waiting after the first limit event, then 16384 cycles before a restart attempt, which at 480 kHz is roughly 1 ms and 34 ms
Frequency200 kHz to 1.6 MHz set by a resistor on RT/CLK; 240 kOhm gives 200 kHz, 100 kOhm gives 480 kHz and 29 kOhm gives 1.6 MHz
Synchronisationthe same pin accepts an external clock, with a 2 V high threshold and a 0.78 V low threshold, and a 66 ns delay from the clock edge to the switch node
Supply current600 uA typical and 800 uA maximum non-switching, 2 uA typical and 5 uA maximum in shutdown
Lockout and enableVIN lockout at 4.0 V rising with 150 mV of hysteresis; EN rising at 1.21 V to 1.26 V and falling at 1.10 V to 1.17 V, with a 3.3 uA hysteresis current
Power goodfault below 92 percent of the reference, good above 94 percent rising, fault above 106 percent and good again below 104 percent, 2 mA sink
Thermalshutdown between 160 C and 175 C with 10 C of hysteresis and a 16384 cycle hiccup, junction to ambient 47.2 C/W on the document test board

Family variants and how they differ

TPS54821 against the 6 A family membersthe same body and pin out carry 6 A and 4 A versions, so the board can be re-rated without a new footprint
Current mode against D-CAPthis part uses a voltage mode error amplifier into a current comparator and needs an external compensation network on COMP, unlike the D-CAP2 family
TrackingSS/TR can be driven from an external ramp for sequencing, with the pin overriding the internal reference, and a 20 mV to 60 mV matching window against VSENSE
Hiccup against latchthe part retries by itself after the 16384 cycle wait; there is no latch option in this document
Boota bootstrap capacitor between BOOT and PH is required, and the high side drive is locked out below 2.1 V to 3 V of boot to phase voltage

Points to check before this part goes on a BOM

The 8 A rating moves with junction temperature and the document says so in the recommended operating conditions rather than in a footnote. At 8 A the junction must stay at or below 125 C, and holding 150 C drops the rating to 6 A. On a 47.2 C/W board that is 8 A with about 55 C of rise above ambient, so an 8 A load in 70 C air needs the thermal pad tied to a plane with vias, not just to the top copper.

The hiccup timing is worth converting into time because it decides whether a system sees a short as a restart or as a dead rail. The 512 cycle wait at 480 kHz is about 1 ms of current limiting before the part shuts down, and the 16384 cycle wait before the next attempt is about 34 ms. At 200 kHz those become 2.6 ms and 82 ms, so the retry duty cycle falls as the frequency falls, which is the behaviour a hot swap or a motor load wants.

The split rail is the feature that separates this part from a plain 17 V buck. PVIN can be 1.6 V while VIN sits at 5 V or 12 V, which is how a 1 V core rail is generated from a 1.2 V intermediate bus with the control circuit still fed from a 5 V housekeeping rail. Tying VIN and PVIN together works, but then the minimum input is 4.5 V and a 3.3 V bus cannot supply the part at all.

Compensation is external, which is the one place where a drop in replacement from a D-CAP2 part goes wrong. The error amplifier has 1300 uMhos of transconductance and 4000 V/V of DC gain, and the network on COMP has to match the output capacitor and the crossover the system needs. A board that copies the output components from a D-CAP2 rail will oscillate here, and the fix is a compensation network rather than a bigger output capacitor.

Reading the current limit windows

The high side limit is 14.5 A typical between a 10.5 A minimum and a 17 A maximum, and the low side has its own sourcing window from 9.5 A to 15 A. Because the high side comparator is cycle by cycle, a short on the output trips on the first cycle above the limit, while an overload that only reaches 12 A may run indefinitely at the maximum junction temperature.

The low side sinking limit of 2 A to 4 A is the one that protects a pre-biased start. It turns the low side FET off rather than allowing reverse current, so a rail that is already charged is not pulled down through the switch when the converter starts.

Frequency choice and inductor size

The resistor on RT/CLK sets the frequency, and the document gives three anchor points: 240 kOhm for 200 kHz, 100 kOhm for 480 kHz and 29 kOhm for 1.6 MHz. Higher frequency shrinks the inductor and the output capacitors but raises switching loss in the 26 mOhm high side FET, and the minimum on time of 94 ns to 145 ns caps the frequency that a 12 V to 1 V conversion can use.

Synchronising to an external clock is the same pin, and the 66 ns delay from the clock edge to the switch node is the number that decides whether two rails on one board can be phase shifted without overlap.

Where this order code fits

It feeds core and input output rails on set top boxes, digital televisions, home gateways and point of load supplies where 8 A has to come from a 12 V bus. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Can PVIN run below 4.5 V? Yes, PVIN goes down to 1.6 V, but VIN must stay between 4.5 V and 17 V because it supplies the control circuit. On a single rail the effective minimum is 4.5 V.

What is the output current at 150 C junction? 6 A. The 8 A row applies only while the junction stays at or below 125 C.

Does the part latch off on a short? No. It limits for 512 cycles, waits 16384 cycles and retries, and the same hiccup applies to thermal shutdown.

Is an external compensation network required? Yes, on COMP. The device is a current mode converter with a transconductance error amplifier, not a D-CAP2 part with an internal ramp.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.