Contact Us

TPS54620RHLR

Brand: Texas Instruments
Texas Instruments TPS54620RHLR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS54620RHLR — Power Management & Signal Chain | Superb Automation

TPS54620RHLR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS54620RHLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS54620RHLR: 6 A synchronous step-down converter with a split power rail from 1.6 V to 17 V

TPS54620RHLR is a 6 A synchronous buck converter in a 3.5 mm by 3.5 mm QFN that takes its power stage from one rail and its bias from another, with both MOSFETs inside the package in a VQFN body of 14 pins. The TPS54620 regulates from a VIN rail of 4.5 V to 17 V and can carry the switching current from a PVIN rail as low as 1.6 V, which is what the split rail feature is for: a 12 V bus feeds the bias and a lower rail feeds the power stage. The high side switch is 26 mOhm at a 6 V boot charge and the low side is 19 mOhm, both inside a body with an exposed thermal pad. Switching runs from 200 kHz to 1.6 MHz set by one resistor, or locked to an external clock, and the reference is 0.8 V with one percent accuracy over the full junction range. Shutdown current is 2 uA.

Order code and package

Order codeTPS54620RHLR
Input voltage, VIN4.5 V to 17 V
Power stage input, PVIN1.6 V to 17 V
Rated output current6 A
Integrated switcheshigh side 26 mOhm, low side 19 mOhm
Switching frequency200 kHz to 1.6 MHz, set by an RT resistor
Synchronisationlocks to an external clock through the RT/CLK pin
Voltage reference0.8 V, plus or minus 1 percent over temperature
Shutdown current2 uA typical
Package14 pin VQFN, 3.5 mm by 3.5 mm, exposed pad
Pin count14
DocumentSLVS949F, May 2009, revised May 2017

Electrical parameters that decide the application

High-side switch resistance26 mOhm at BOOT to PH of 6 V, 32 mOhm at 3 V
Low-side switch resistance19 mOhm with VIN at 12 V
High-side current limit8 A minimum, 11 A typical
Low-side sourcing limit7 A minimum, 10 A typical
Low-side sinking limit2.3 A
Reference window0.792 V to 0.808 V over the rated load range
Input UVLO4 V rising minimum, 4.5 V maximum, 150 mV hysteresis
Non-switching supply current600 uA typical, 800 uA maximum
Thermal resistance40.1 C per W junction to ambient on a four layer board
Junction range-40 C to 150 C
Soft-start charge current2.3 uA into the SS/TR capacitor
Minimum controllable on time94 ns typical, 135 ns maximum at 12 V in

Points to check before this part goes on a BOM

The split rail is the reason to pick this part over a single input buck. VIN has to stay above 4.5 V because it feeds the internal bias regulator, but PVIN can drop to 1.6 V, so a 2.5 V bus can feed the power stage while a 12 V rail keeps the housekeeping alive. Tying PVIN and VIN together is allowed and is what most boards do, but the two pins are not interchangeable and a board that feeds only PVIN will not start.

A 6 A rating with an 8 A minimum high-side current limit means the margin above the load is small by converter standards. At 6 A of load with a 30 percent inductor ripple the peak switch current is about 6.9 A, which is inside the 8 A minimum but not far inside it. Boards that run at the full rating with a low inductance value should check the ripple current against that minimum limit rather than against the typical figure.

Switching frequency is a size and loss trade that the board fixes early. At 200 kHz the inductor is large and the switching loss is low; at 1.6 MHz the output capacitance can be small but the high-side switch spends more time in the linear region. The RT resistor sets it, and the tolerance of that resistor shows up directly as a frequency tolerance, which is why the document asks for a one percent part in the RT position.

The 94 ns minimum on time is the limit on conversion ratio at high frequency. A 12 V to 0.9 V rail at 1.6 MHz needs a 450 ns period and a 34 ns on time, which the part can hold; the same conversion at 1.6 MHz with the on time falling below 94 ns forces the controller to skip pulses, and the output ripple that results is regular but larger than the steady state figure.

Thermal performance depends almost entirely on the pad. 40.1 C per W junction to ambient is quoted for a board with a thermal via array under the body, and a two layer board with a single via per pad runs far hotter at the same dissipation. At 6 A from 12 V to 1 V the loss is roughly 1 W, so the pad and the copper around it decide whether the part stays inside its 150 C limit at a 60 C ambient.

The power good output monitors a window, not a single threshold. It pulls low when the sense voltage falls below 91 percent of the reference or rises above 109 percent, and it needs the soft-start pin above 1.4 V before it will report good. A sequencer that watches PWRGD therefore sees a fault on an overvoltage as well as an undervoltage, which is useful on a rail feeding a load that must not run above its rating.

Ordering the RHLR suffix matters for assembly. The RHL body is the 14 pin 3.5 mm QFN with the exposed pad and the R suffix is the tape and reel, so a line that has been buying a larger package cannot drop this part in without a stencil change. The order code also fixes the temperature grade, which is the full -40 C to 150 C junction range on this catalogue number.

Where this order code fits

This order code belongs on point of load rails in telecom line cards, optical transport shelves, industrial control boards and broadband equipment where a 5 V or 12 V intermediate bus has to become a 1 V to 3.3 V core rail at up to 6 A. The split rail option suits boards that already carry a 3.3 V housekeeping rail and want the buck stage fed from a lower bus to cut switching loss. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

Can PVIN be connected to the same rail as VIN? Yes, and that is the common arrangement. What is not allowed is driving PVIN while VIN is below its 4.5 V start threshold, because the bias regulator and the gate drive come from VIN.

What sets the current limit? The high-side switch senses peak current at 8 A minimum and the low-side senses sourcing current at 7 A minimum. Both limits move with temperature and with the boot charge voltage.

Is 1.6 MHz usable at a 12 V input? Only at conversion ratios that keep the on time above 94 ns. A 12 V to 3.3 V rail at 1.6 MHz needs about 170 ns, which is comfortable; a 12 V to 1 V rail does not.

SUPERB supplies this order code with date codes, packing and country of origin on the offer, and the Component Lead Time Solutions page lists the fields to compare before a point of load socket is filled from another line.