Contact Us

TPS54613PWPR

Brand: Texas Instruments
Texas Instruments TPS54613PWPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS54613PWPR — Power Management & Signal Chain | Superb Automation

TPS54613PWPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS54613PWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS54613PWPR 6 A fixed 1.5 V converter for a 3.3 V or 5 V bus

The TPS54613PWPR is a 6 A synchronous buck converter that runs from 3 V to 6 V in and delivers a fixed 1.5 V out, one member of a family that also offers 0.9 V, 1.2 V, 1.8 V, 2.5 V and 3.3 V versions in the same 28 pin HTSSOP body. The switches are 30 milliohm with a 12 A peak rating, the output accuracy is 1 per cent initially, and the loop is internally compensated, so the circuit is an inductor, a few capacitors and two resistors for the divider that the fixed version does not even need.

This is a part from the era when a 1.5 V rail meant a memory termination or a DSP core fed from the 3.3 V bus, and it still fits that job because the 3 V minimum input sits below a 3.3 V rail with 10 per cent tolerance and the 6 A rating covers a bank of memory or a small processor. The switching frequency is fixed at 350 kHz or 550 kHz depending on the part number and can be set from 280 kHz to 700 kHz with a resistor on RT on the adjustable rows.

The slow start is internal and linear: the reference ramps from 0 to 0.891 V in 3.35 ms, which sets the inrush into the output capacitor without an external capacitor. A power good output is provided for reset and sequencing, and the enable pin allows the rail to be held off until the input is valid.

Key parameters from the SLVS400D document

Input range3 V to 6 V operating, with the undervoltage lockout stopping the part below a nominal 2.95 V and 3 per cent tolerance on that threshold
OutputFixed 1.5 V for this member, 1 per cent initial accuracy, with the family covering 0.9 V to 3.3 V in the same body
Output current6 A continuous from 30 milliohm switches rated for a 12 A peak
Switching frequencyFixed 350 kHz or 550 kHz by part number, or adjustable from 280 kHz to 700 kHz with a resistor on RT on the adjustable rows
Current limit7.2 A minimum and 10 A maximum at 6 V input, with 10 ns to 12 ns of leading edge blanking and a 100 ns total response time
Quiescent current2.7 mA typical and 3.0 mA maximum at 350 kHz, 2 microamp in shutdown with SS/ENA low
Thermal shutdownTrip point between 135 and 165 degrees, with hysteresis before the part restarts
Orderable bodyHTSSOP PWP, 28 pins, 2000 pieces on a large reel with a 353 mm carrier

Fixed output is a supply chain decision as much as an electrical one

A fixed output converter removes the divider, the divider error and the divider drift, and it also removes a class of build error: the same body programmed for 1.2 V and 1.5 V looks identical on the reel. The trade is that the rail can only be trimmed by changing the part number, so a board that needs 1.45 V instead of 1.5 V needs a different order code rather than two resistors.

The family approach is why these parts lasted: one body, one footprint, six output voltages, so a platform could carry three different rails with one placement program. A supply chain that still supports such a board has to keep all six order codes visible, because the reel that is out of stock is usually the one the build needs.

Protection and sequencing

Cycle by cycle current limiting measures the high side switch current with 10 ns to 12 ns of leading edge blanking to stop the switching spike from tripping the comparator, and the total response time is 100 ns. Beyond the limit the part folds back and, if the condition persists, the thermal shutdown at 135 to 165 degrees takes over. Power good is asserted when the output is inside regulation, and the enable pin can hold the part off until the input rail is valid.

The internal slow start of 3.35 ms for a 0.891 V ramp is fixed, so the inrush into a large output capacitor is set by that time. A 1000 microfarad output at 1.5 V draws about 450 mA during the ramp, which is inside the 7.2 A limit but is also why the input supply has to be able to deliver it.

Where this part fits

A 1.5 V rail at 6 A from a 3.3 V or 5 V bus is the classic memory termination or DSP core supply, and the same part serves an FPGA auxiliary rail on an older platform that is still in production. Because the body is a 28 pin HTSSOP with a thermal pad, the heat path is through the pad and the copper under it, which is easier to control than a small QFN on a two layer board.

Boards built around this family are usually long life industrial or telecom products, so the sourcing question is availability rather than performance, and that is where component obsolescence management and last time buy and LTB planning come in.

What to check before a purchase order

The first field is the output voltage code inside the part number, since the six members share one document and one body and a wrong digit gives a rail that is 0.3 V off. The second is the frequency option, 350 kHz or 550 kHz, which changes the inductor and the ripple. The third is the reel, 2000 pieces on this row, because the carrier is 353 mm and does not fit every feeder.

Our desk decodes the order code against the family table before quoting, so a customer who asks for the 1.5 V member does not receive the 1.8 V one with the same marking. See power management cross reference and one stop BOM sourcing.