Contact Us

TPS54527DDAR

Brand: Texas Instruments
Texas Instruments TPS54527DDAR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS54527DDAR — Power Management & Signal Chain | Superb Automation

TPS54527DDAR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS54527DDAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS54527DDAR 18 V input 5 A converter with a D-CAP2 loop

The TPS54527DDAR is a 5 A synchronous step down converter that runs from 4.5 V to 18 V and delivers 0.76 V to 6 V out of an 8 pin SO PowerPAD body. Where most converters in this class need a compensation network, this one uses D-CAP2 control, an adaptive on time loop that responds to the output voltage directly and therefore needs no external compensation components at all. The switches are 65 milliohm high side and 36 milliohm low side.

The absence of a compensation network is the reason the part appears in so many cost sensitive boards. A 5 A rail that has to be stable with a single 22 microfarad ceramic and with a 470 microfarad electrolytic, without changing the bill of materials, is exactly what D-CAP2 is built for: the loop adapts to the equivalent series resistance of whatever capacitor is fitted, which is a property the vendor calls out explicitly for both POSCAP style bulk parts and ceramics.

An internal 5 V regulator, VREG5, is brought out on a pin and drives the gate of the high side switch, so the part works from a 4.5 V input without a separate bias rail. The 5.2 V to 5.7 V window on that regulator is also the supply for the internal logic, and its undervoltage lockout is what turns the part off when the input collapses.

Key parameters from the SLVSAY5D document

Input range4.5 V to 18 V, with the wake up threshold on VREG5 between 3.45 V and 4.05 V
Output range0.76 V to 6 V, set by a divider against the 765 mV reference
Output current5 A continuous from a 65 milliohm high side and a 36 milliohm low side switch
Reference765 mV typical, 757 mV to 773 mV at 25 degrees and 751 mV to 779 mV over minus 40 to 85 degrees
Current limit5.6 A minimum, 6.4 A typical and 7.9 A maximum, valley sensed on the low side switch
Quiescent current900 microamp typical and 1.4 mA maximum non switching, 3.6 microamp typical and 10 microamp maximum in shutdown
On time150 ns typical at 12 V input and 1.05 V output, with a minimum off time that limits the maximum duty
Orderable bodySO PowerPAD DDA, 8 pins, 2500 pieces on a large reel, with a .A and a .B row in the addendum

What D-CAP2 does with the output capacitor

Adaptive on time control compares the feedback against an internal ripple rather than against a fixed sawtooth, so the loop gain follows the output capacitor impedance. That is why the part tolerates both a low ESR ceramic bank and a higher ESR bulk capacitor without a compensation change, and why a board that swaps capacitors for cost reasons usually keeps working.

The trade is that the switching frequency is not fixed: it moves with the input and output voltages and with the load. A 12 V to 1.05 V conversion runs near 500 kHz at full load and drops at light load, which matters for an EMC scan and for a filter chosen at a single frequency. The 150 ns on time figure is what limits the conversion ratio at high input.

Protection behaviour

Current limiting is valley sensed on the low side switch at 5.6 A minimum, 6.4 A typical and 7.9 A maximum. Because the valley is what is measured, the peak inductor current at the moment of trip is the valley plus the ripple, and a board with a small inductor reaches a higher peak than the number suggests. Thermal shutdown sits at 165 degrees with hysteresis, and the VREG5 regulator has its own undervoltage lockout that stops switching when the internal rail collapses.

Where this part fits

Digital televisions, set top boxes, cable modems, LCD monitors and industrial control boards use a 5 A rail from 12 V, and the 8 pin SO PowerPAD is one of the easiest bodies to rework in a pilot line. The same part serves a 5 V to 3.3 V rail on a board that has both buses, since the 4.5 V minimum input is met with margin.

For a procurement team the relevant point is that the same document covers several revisions of the same body, and the reel a distributor holds may be any of them. That is the sort of question where date code management and power management cross reference do the work before a purchase order is placed.

What to check before a purchase order

The first field is the revision row, since the addendum carries a plain row, a .A row and a .B row for the same body and the silicon behind them has changed over the product life. The second is the package, DDA being the 8 pin SO PowerPAD with the exposed pad that must be soldered to the ground plane. The third is the output divider, because the reference sits at 765 mV and a divider copied from a 0.8 V part gives a rail about 4 per cent low.

Our desk reads the revision off the reel label rather than off the order line, and flags a mixed lot before it reaches the line. See incoming inspection plan for the check itself.