TPS543820RPYR
Product Specifications
TPS543820RPYR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS543820RPYR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS543820RPYR 18 V input 8 A buck in a 2.5 mm by 3 mm body
The TPS543820RPYR is an 8 A synchronous step down converter that takes 4 V to 18 V in and delivers 0.5 V to 7 V out from a 14 pin HotRod VQFN measuring 2.5 mm by 3 mm. The switches are 25 milliohm high side and 6.5 milliohm low side. What makes the part interesting is not the current but the control: an internally compensated advanced current mode loop with three selectable ramp options, so the compensation is inside the body while the loop still behaves well across a range of output capacitors.
That combination is what allows a point of load converter to sit next to the load instead of next to the input connector. At 2.2 MHz the inductor falls to a fraction of a microhenry and the output capacitor bank shrinks to ceramics, which is how a 30 A rail on a line card gets split into four 8 A phases placed where the current is actually consumed. The five selectable frequencies, 500 kHz, 750 kHz, 1 MHz, 1.5 MHz and 2.2 MHz, are set by one resistor on MODE and the part can also be synchronized to an external clock so several converters share a beat.
The reference is 0.5 V with 0.5 per cent accuracy over the full temperature range, which is tighter than the 1 per cent that older parts in this class quote at 25 degrees only. The 0.5 V bottom of the output window is what makes the part usable for a 0.6 V core rail without an external divider that would eat the accuracy.
Key parameters from the SLUSED1B document
| Input range | 4 V to 18 V, with the internal BP5 rail at 4.5 V and 350 mV of dropout at 3.8 V input |
| Output range | 0.5 V to 7 V with a 500 mV reference, 497.5 mV to 502.5 mV over minus 40 to 150 degrees junction |
| Output current | 8 A continuous from integrated 25 milliohm high side and 6.5 milliohm low side switches |
| Switching frequency | 500 kHz at 24.3 k on MODE, 1 MHz at 11.8 k and 2.2 MHz at 4.99 k, with each row specified as a window rather than a point |
| Current limit | High side peak 11.7 A to 12.7 A in the 500 kHz setting and 8.6 A to 9.6 A in the higher limit setting, low side sourcing 9.4 A to 11.3 A and 6.2 A to 8.5 A respectively |
| Quiescent current | 1.2 mA typical and 1.6 mA maximum non switching, 15 microamp typical and 25 microamp maximum in shutdown |
| Soft start | Four selectable times, 0.5 ms, 1 ms, 2 ms and 4 ms, chosen by the same mode resistor |
| Orderable body | HotRod VQFN-HR, 14 pins, 2.5 mm by 3 mm, 3000 pieces on a large reel at moisture level 2 with a one year floor life |
How the mode resistor packs four settings into one pin
One resistor on MODE sets the switching frequency, the ramp option and the soft start time, and the current limit is chosen from a second resistor on the same network. The window on each frequency row, 450 kHz to 550 kHz at 24.3 k for example, is the part telling you that the resistor tolerance and the internal spread both land inside that band. A board that has to sit exactly at 2.2 MHz to avoid an AM band therefore needs a 1 per cent resistor, not a 5 per cent one.
The three ramp options exist because the same loop has to stay stable with a single 22 microfarad ceramic and with a bank of 470 microfarad bulk capacitors. Choosing the ramp that matches the output capacitor bank is the difference between a converter that recovers from a load step in a few microseconds and one that rings for fifty.
Where 8 A at 2.2 MHz actually helps
Wireless infrastructure and optical line cards run many low voltage rails in a small space and care about the height of the components as much as the area. A 2.2 MHz converter with a 0.47 microhenry inductor and ceramic output capacitors fits under a heat sink and stays out of the way of the optical cage. The same part at 500 kHz serves an industrial board where efficiency matters more than size.
Test and measurement equipment and medical instrument front ends use the higher frequency setting to keep the switching fundamental out of the band their own acquisition circuit cares about, and the external synchronization pin lets the converter lock to a system clock so the interference lands on a known frequency instead of drifting.
What to watch in the thermal path
Eight amps through 6.5 milliohm on the low side is 0.42 W of conduction loss at full load before switching loss, and the 2.5 mm by 3 mm body has to move that through the exposed pad into the copper. The HotRod package puts the pads on the edge of the body, which shortens the loop and reduces the parasitic inductance, but it also concentrates the heat in a small area. A four layer board with the pad stitched into an inner plane handles 8 A comfortably; a two layer board at 2.2 MHz will not.
Where this part fits
Point of load conversion on communication line cards, optical modules, test instruments and medical front ends is the natural home for this part, together with any board that has to fit a 0.5 V core rail into a space smaller than the connector next to it. The externally synchronizable clock and the tight reference matter when several rails have to track each other.
For procurement the useful angle is that the family covers 500 kHz to 2.2 MHz with one body and one footprint, so a board can be retuned for efficiency or for size without a change in the pick and place program. The comparison method is set out in power management cross reference, and the reel and date code side is covered in date code management.
What to check before a purchase order
The first field is the package, since the same silicon is published in more than one body and the pad geometry differs. The second is the mode resistor value on the customer board, because a reel of the right part installed with the wrong MODE resistor runs at the wrong frequency and the wrong current limit. The third is the moisture level and floor life, level 2 with a one year floor life on this row, which decides whether the reel needs baking before it goes on the line.
Our desk quotes the body and the reel together and flags the floor life on the packing list rather than leaving it to the line to discover. See incoming inspection plan for how that check is carried out at goods in.