Contact Us

TPS54360BQDDARQ1

Brand: Texas Instruments
Texas Instruments TPS54360BQDDARQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS54360BQDDARQ1 — Power Management & Signal Chain | Superb Automation

TPS54360BQDDARQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS54360BQDDARQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS54360BQDDARQ1: 3.5 A step-down converter with a 60 V input in an eight pin HSOIC with a PowerPAD

TPS54360BQDDARQ1 is a 60 V input buck converter with an integrated high-side switch and a 92 mOhm channel, built for industrial and automotive rails that see transients in a HSOIC body of 8 pins. The TPS54360B takes 4.5 V to 60 V in, with a 65 V absolute maximum, and delivers 3.5 A continuous with a 4.5 A minimum peak inductor current limit. The high-side switch is 92 mOhm, the reference is 0.8 V with one percent accuracy, and the switching frequency is programmable from 100 kHz to 2.5 MHz or locked to an external clock. Operating quiescent current is 146 uA, shutdown current is 2.25 uA, and the body is an eight pin HSOIC with a PowerPAD for thermal transfer.

Order code and package

Order codeTPS54360BQDDARQ1
Input voltage4.5 V to 60 V, 65 V absolute maximum
Output current3.5 A continuous
Peak inductor current limit4.5 A minimum, 5.5 A typical, 6.25 A maximum
High-side switch92 mOhm typical, 190 mOhm maximum at 12 V in
Voltage reference0.8 V, 0.792 V to 0.808 V
Switching frequency100 kHz to 2.5 MHz, set by an RT resistor or an external clock
Quiescent current146 uA typical, 175 uA maximum
Shutdown current2.25 uA minimum, 4.5 uA maximum
Input UVLO4.1 V minimum, 4.3 V typical, 4.48 V maximum rising
Package8 pin HSOIC with a PowerPAD, 4.89 mm by 3.90 mm
Soft-start time2.1 ms at 500 kHz, 0.42 ms at 2.5 MHz
DocumentTPS54360B data sheet, automotive qualified

Electrical parameters that decide the application

Minimum on time135 ns at 12 V in and 25 C
Current limit delay60 ns
Frequency at 200 kOhm500 kHz, 450 kHz to 550 kHz
Thermal shutdown176 C, 12 C hysteresis
Error amplifier transconductance350 uS
Compensation to switch transconductance12 A per V
Enable threshold1.1 V to 1.3 V, with a hysteresis current of -3.4 uA
Junction range-40 C to 150 C
Light loadpulse skipping eco-mode keeps efficiency up
Boot rechargeintegrated FET, so the boot capacitor recovers at light load
UVLO adjustmentexternal divider with adjustable hysteresis
Protectioncycle by cycle current limit, thermal shutdown, frequency foldback

Points to check before this part goes on a BOM

Sixty volts with a 65 V absolute maximum is what a 48 V industrial rail needs. A nominal 48 V bus with a five percent tolerance is 50.4 V, and a transient suppressor clamps at a level above that. A part rated at 40 V would be over its limit during a normal event rather than an abnormal one, which is why this family is ordered for those rails.

The 4.5 A minimum peak current limit against a 3.5 A continuous rating leaves a workable margin. At 3.5 A with 30 percent ripple the peak is 4.03 A, inside the minimum. The load that trips the limit is therefore a real overload rather than a normal transient, which is the behaviour a system wants: the rail rides through a load step and only limits on a fault.

Two point five megahertz is a large range, and the top of it is where the minimum on time bites. A 48 V to 3.3 V rail needs a 6.9 percent duty cycle; at 2.5 MHz that is 27 ns, well below the 135 ns minimum on time. The part therefore drops pulses at that combination, and a board that needs a clean 3.3 V from 48 V should run at 300 kHz to 500 kHz instead.

The integrated boot recharge FET is a small feature with a large effect at light load. A converter that has to skip pulses for long intervals can lose its boot charge if the refresh path depends on switching, and the high-side switch then fails to turn on cleanly. Here the boot capacitor is topped up through an integrated device, so the pulse skipping does not degrade the gate drive.

Eco-mode pulse skipping holds efficiency up at millamp loads, at the cost of a ripple that is larger and lower in frequency than the continuous figure. On an automotive rail that feeds a module in sleep mode, that trade is the right one. On a rail that feeds an analog measurement it is not, and the board should either keep a preload or use a part without the mode.

The Q1 suffix carries the qualification record, not a different die. A build that moves from the industrial part to the automotive part keeps the same external components and the same behaviour, but the documentation, the traceability and the temperature range are those of the automotive flow. That distinction is what a customer audit asks about.

An eight pin HSOIC with a PowerPAD is a package that a rework station can handle, and the pad can be inspected from the side. At 3.5 A with a 48 V input the loss is around 1.2 W, most of it in the switch, so the pad and the copper under it are what keep the junction inside 150 C at a 70 C ambient.

Where this order code fits

This order code fits 24 V and 48 V industrial rails, automotive body and infotainment supplies that see load dump, telecom cards and motor drive logic supplies. The Q1 suffix means the automotive qualification flow, so the same silicon is used where the qualification record has to match the automotive standard. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Is this part automotive qualified? The Q1 suffix identifies the automotive qualification flow, and the order code carries the qualification record with it.

What is the difference from the non automotive part? The same function and the same external components, with the documentation and the qualification record of the automotive flow.

Can it run at 2.5 MHz from a 48 V rail? Not at a 3.3 V output. The minimum on time of 135 ns is reached before that duty cycle, so the part skips pulses.

SUPERB supplies this order code with date codes and packing, and the OEM Procurement page covers what an audit expects when a 48 V rail has to stay sourced through a long production life.