Contact Us

TPS54339EDDAR

Brand: Texas Instruments
Texas Instruments TPS54339EDDAR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS54339EDDAR — Power Management & Signal Chain | Superb Automation

TPS54339EDDAR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS54339EDDAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS54339EDDAR: a 3 A synchronous step down converter that runs from a 4.5 V to 23 V input in an 8 pin SO PowerPAD body

TPS54339EDDAR is an adaptive on time synchronous buck converter with both switches inside the package, a 0.765 V reference and a fixed 600 kHz switching frequency in a SO PowerPAD (DDA) body of 8 pins. It carries 3 A from a 140 milliohm high side switch and a 70 milliohm low side switch, sets the output anywhere from 0.76 V to 7 V with two resistors, draws 600 microamp of supply current when switching with no load and 3 microamp in shutdown, and limits the high side switch between 3.5 A and 5.7 A. The junction range runs from minus 40 C to 150 C.

Order code and package

TPS54339EDDARSO PowerPAD (DDA) body, 8 pins with an exposed thermal pad, 2500 pieces on a large reel, nickel palladium gold finish, moisture level 2 at 260 C for one year floor life, marking 54339E, active status in the addendum dated 11 November 2025
TPS54339EDDAthe same die and the same body on a 75 piece tube, which is the string a repair line orders when it needs a handful rather than a reel
.A suffix rowsthe addendum repeats both strings with an .A suffix, and the packing, finish and marking have to be read on the row rather than taken from the suffix
Absent stringsthere is no TPS54339EDDAT small reel row and no -Q1 automotive row in this document, so a small quantity request is met by cutting a reel or by a tube, not by a part number
Body sizethe DDA body is the 8 pin small outline with the exposed pad, and the pad is the only path from the die to the board copper
Ambient rangeevery row is written for minus 40 C to 85 C ambient, while the junction tables run to 150 C, so the two numbers are not the same figure
Marking54339E on all rows, which is how a tube is identified when the label has been lost

Electrical parameters that decide the application

Input voltage4.5 V to 23 V in the recommended operating table, and the front page states the same window, while the description paragraph still carries the older 18 V sentence, so the 23 V figure is the one to quote against a 24 V rail with margin
Output voltage0.76 V to 7 V set by a divider from the output to the VFB pin against a 0.765 V reference, which measures 749 mV to 781 mV over temperature
Output current3 A continuous from the two integrated switches, with the inductor value setting the ripple at that current
Switch resistance140 milliohm on the high side and 70 milliohm on the low side, which is what keeps the conduction loss at 3 A inside the 8 pin body
Switching frequency600 kHz fixed, with no resistor to change it, so the inductor and the output capacitor are chosen around that one number
Supply current600 microamp typical and 1100 microamp maximum in non switching operation at 25 C, which includes the internal 5.5 V regulator feeding its own control circuit
Shutdown current3 microamp typical and 10 microamp maximum with the enable pin at zero volts
Current limit3.5 A minimum, 4.1 A typical and 5.7 A maximum on the high side switch, cycle by cycle, which is the number that decides whether a 3 A load with a 30 per cent transient survives
Soft starta capacitor on the SS pin charged by 4.2 to 7.8 microamp, and the ramp time in milliseconds is the capacitor value in nanofarad times 0.765 times 1.1 divided by that current
Internal railVREG5 sits at 5.2 V to 5.7 V and can give 20 mA, which is enough for the gate drive and nothing else
Enable thresholds1.6 V to turn on and 0.6 V to turn off, with a 200 to 800 kilohm resistance to ground on the pin, which lets a divider set a user defined undervoltage lockout
Timing160 ns on time at 12 V in and 1.05 V out, with a minimum off time of 260 ns to 310 ns, which is what caps the duty cycle at high input to low output ratios
Protectionoutput overvoltage at 125 per cent of the set point, undervoltage hiccup at 65 per cent, and thermal shutdown at 165 C
Loopthe D-CAP2 control needs no external compensation, so the components around the part are the inductor, the output capacitor and the divider

Family variants and how they differ

Eco-modeat light load the converter skips cycles instead of holding continuous conduction, which is where the 600 microamp figure comes from and why the output ripple grows when the load falls below about 10 per cent of rating
E revisionthe E in the string is the revision that carries the 23 V front page rating and the current limit window quoted here, so a quote for a plain TPS54339 is not the same device
Pre-biased startthe low side switch stays off while the output is already held up by another source, so a shared rail does not get pulled down at power up
Ceramic output capacitorsthe loop is stable with low equivalent series resistance parts, which is the reason the compensation is internal rather than pinned out
Tube and reelthe same die ships in a 75 piece tube and a 2500 piece reel, and both are moisture level 2, so the floor life clock starts when the bag is opened either way
Thermal padthe exposed pad is connected to ground inside the package, so the copper under it is both the electrical return and the heat spreader

Points to check before this part goes on a BOM

The input window on the front page is 23 V and the description paragraph says 18 V. The recommended operating table agrees with 23 V, so a 24 V industrial rail is inside the rating, but the offer should quote the table rather than the paragraph.

The thermal pad carries the heat. At 3 A into a 0.76 V rail from 12 V the conduction loss and the switching loss together are several hundred milliwatt, and a board that leaves the pad unconnected will reach thermal shutdown before the current limit is reached.

The soft start capacitor is the only control over inrush. With 4.2 to 7.8 microamp of charge current the ramp is slow enough that a 10 nF capacitor gives roughly 1 ms, and a 100 nF capacitor gives roughly 10 ms, which is the range most 5 V rails need.

VREG5 is not a spare supply. It can give 20 mA and it feeds the gate drive, so loading it with an external circuit will disturb the switching behaviour rather than simply drop a rail.

The enable pin has an internal resistance to ground, which means a floating enable does not guarantee the converter is off. A divider or a driven signal is the reliable way to hold it down.

What a fixed 600 kHz means for the parts around it

The switching frequency is set inside the device, so the inductor is chosen for one operating point rather than a range. At 12 V in and 1.8 V out the duty cycle is short, the ripple current depends on the inductor and the 600 kHz number, and a 2.2 microhenry part lands the ripple at about 40 per cent of the 3 A load.

A higher inductance lowers the ripple and slows the transient, and a lower inductance does the opposite. Because the loop compensation is fixed inside the part, the output capacitor has to be chosen for stability rather than for size alone: the data sheet curves are written for ceramic parts in a narrow range, and a large electrolytic will move the crossover point.

Where this order code fits

The part fits a point of load rail in a set top box, a digital television or a home gateway, where a 12 V or 19 V adapter has to come down to a 1.2 V or 1.8 V core rail at 3 A. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Does the 23 V rating apply to a 24 V rail? The recommended operating maximum is 23 V, so a regulated 24 V rail sits above it and is not covered. A 24 V rail with five per cent tolerance needs a different part or a front end clamp.

What sets the output voltage? A divider from the output to the VFB pin against the 0.765 V reference. The reference is specified from 749 mV to 781 mV over temperature, so the divider ratio is fixed and the tolerance comes from the reference.

Can the switching frequency be changed? No. It is fixed at 600 kHz and there is no timing pin, so a board that needs a different frequency or synchronisation to an external clock needs a different converter.

Is this string in stock at the distributor level? SUPERB quotes against the exact ordering string, with date codes, packing and country of origin stated on the offer, and confirms the reel or tube quantity before the order is placed.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.