Contact Us

TPS54318RTER

Brand: Texas Instruments
Texas Instruments TPS54318RTER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS54318RTER — Power Management & Signal Chain | Superb Automation

TPS54318RTER

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS54318RTER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS54318 3 A 2 MHz synchronous converter in a 3 mm by 3 mm body

The TPS54318RTER is a 2.95 V to 6 V input, 3 A synchronous step down converter with two integrated 30 milliohm switches and a switching frequency that can be set from 200 kHz to 2 MHz. It sits in the 16 pin 3 mm by 3 mm WQFN body and is the low input member of a family that also covers 18 V and 28 V rails. The reference is 0.8 V with 1 per cent over temperature, and the part carries an adjustable soft start, a power good output that watches both undervoltage and overvoltage, and a cycle by cycle current limit with frequency foldback.

This is a point of load part. The input range says so: 2.95 V to 6 V is a 5 V or 3.3 V intermediate bus, not a 24 V rail. Its job is to take that bus down to 1.8 V, 1.2 V or 0.9 V at 3 A with a transient response fast enough for a processor, in a footprint that fits beside the processor.

Key parameters taken from the SLVS975C document

Input range2.95 V to 6 V operating, with an internal UVLO that releases around 2.6 V, and 6 V as the top of the recommended range
Output current3 A from two integrated 30 milliohm switches, 44 milliohm at the bottom of the input range
Switching frequency200 kHz to 2 MHz set by the RT resistor, synchronisable to an external clock
Reference0.803 V typical, 0.795 V to 0.811 V over minus 40 to plus 150 degrees, which is the 1 per cent window
Quiescent current350 microamp typical with the output in regulation, 2 microamp in shutdown
Enable pin1.16 V to 1.25 V rising and 1.18 V falling, with 3.2 microamp of input current
Soft startAdjustable with a capacitor on the SS pin, and the part starts monotonically into a prebiased output
Power goodOpen drain, watching both undervoltage and overvoltage, so a rail that overshoots also flags
ProtectionCycle by cycle current limit, frequency foldback, thermal shutdown
Package16 pin WQFN, 3 mm by 3 mm, thermally enhanced

Why 2 MHz matters at 3 A

The inductor value falls with frequency for a given ripple, so a 2 MHz build uses an inductor of roughly a quarter the value of a 500 kHz build at the same ripple current. That is what allows a 3 A rail to fit in the shadow of a processor package. The cost is switching loss, which rises with frequency and with the square of the input voltage, and a 5 V to 1.2 V rail at 2 MHz spends a larger share of its loss budget in the switches than a 500 kHz rail would. The usual compromise on a 5 V intermediate bus is 1 MHz to 1.5 MHz, which keeps the inductor small without pushing the loss above what the 3 mm body can remove.

Prebiased start up and sequencing

A rail that feeds a processor is often already charged through a body diode or an internal path before the converter enables. The part detects that condition and starts without pulling the output down, which avoids a negative current spike and the disturbance that follows. The SS pin sets the ramp, and a capacitor there can be used to sequence this rail after another one, which is the usual approach on a board with a 1.8 V and a 1.2 V rail that must come up in order.

The current limit and what happens in a short

The high side current limit is cycle by cycle, and the frequency folds back when the feedback voltage falls. In a short the part reduces its frequency, which lengthens the off time and limits the average current until the die cools. Recovery is automatic once the short clears, and the ramp behaves like a soft start rather than a step. The failure mode to watch is a short that is just at the limit: the part can sit in a foldback state with a low duty cycle and a hot inductor, which is why the inductor's saturation current should be above the limit, not above the load.

Where the part is used and what the quote should show

Typical sockets are a 5 V to 1.2 V core rail, a 3.3 V to 1.8 V memory or I/O rail, and a 5 V to 0.9 V rail for an FPGA fabric. The 6 V ceiling rules out a 12 V bus, so the part belongs behind an intermediate converter, which is also where its 2 MHz capability pays off.

The orderable string identifies the body and the reel, and the 16 pin WQFN is not interchangeable with the larger body of the higher voltage family members. Our desk quotes the body and reel with the part, and where the exact body is short it shows the pin compatible alternatives and the ones that need a board change separately, on power management cross reference and pin to pin cross reference.

Frequently asked questions

Can the part be synchronised to a system clock. Yes, the RT pin accepts an external clock over the same 200 kHz to 2 MHz range, which is how several rails on one board avoid beat frequencies in a sensitive measurement band.

Does it need an external compensation network. No, the loop is internally compensated for the output capacitor range in the datasheet, and adding an external network is not supported. A different output capacitor outside that range is the usual cause of an unstable rail, not the absence of a compensation pin. See one stop BOM sourcing for the capacitor classes that match.