TPS54312PWPR
Product Specifications
TPS54312PWPR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS54312PWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS54312PWPR: a 3 V to 6 V, 3 A synchronous buck with a fixed 1.2 V output
TPS54312PWPR is a 3 A synchronous buck switcher with integrated FETs and a fixed 1.2 V output in a HTSSOP (PWP) body of 20 pins. The PWP body is the 20 pin HTSSOP with the PowerPAD, 2000 pieces on the large reel. The order code selects the output: TPS54311 is 0.9 V, TPS54312 is 1.2 V, TPS54313 is 1.5 V, TPS54314 is 1.8 V, TPS54315 is 2.5 V and TPS54316 is 3.3 V, all in the same twenty pin body.
Order code and package
| TPS54312PWPR | HTSSOP (PWP), 20 pins with PowerPAD, 2000 piece large reel, NIPDAU finish, MSL level 2 at 260 C with a one year floor life, -40 to 125 C |
| TPS54312PWPT | the small reel string in the same body |
| TPS54312PWPRG4 | G4 carried in the ordering string, same reel and same body |
| Output variants | TPS54311 0.9 V, TPS54312 1.2 V, TPS54313 1.5 V, TPS54314 1.8 V, TPS54315 2.5 V, TPS54316 3.3 V, all fixed and all pin compatible |
| Sink and source | the output stage sources and sinks 3 A continuously, which is what allows the rail to hold a termination or a DDR load |
| Document | SLVS416C, February 2002 and revised January 2015, one of the older SWIFT documents still in production |
Electrical parameters that decide the application
| Input range | 3 V to 6 V operating, which is a 5 V or 3.3 V bus part and not a 12 V part |
| Output | 1.2 V fixed on this member, with 1 percent initial accuracy on the fixed outputs |
| Output current | 3 A continuous source and sink, with 60 mOhm MOSFET switches |
| Switching frequency | 350 kHz with FSEL low, 550 kHz with FSEL high, or adjustable from 280 kHz to 700 kHz with a resistor on RT |
| Current limit | 6.5 A with a 3 V input and 7.5 A with a 6 V input, both measured with the output shorted, so the limit rises with the input |
| Quiescent current | 2.7 mA minimum, 8.4 mA typical and 12.8 mA maximum at 350 kHz with RT open, which is high compared with a modern part and is the price of the bipolar control circuit |
| Slow start | internal, 3.5 ms to 5.4 ms with a 4.5 ms typical, plus a 5 uA charge current on SS/ENA for an external ramp |
| Lockout | 2.80 V stop threshold, so a 3.3 V bus with a 15 percent sag is at the edge |
| Power good | open drain, 90 percent of the reference falling with 3 percent of hysteresis and a 35 us deglitch, 2.5 mA sink at 0.3 V |
| Enable | 0.82 V to 1.40 V threshold with 30 mV of hysteresis and a 2.5 us falling edge deglitch |
| Thermal | shutdown between 135 C and 165 C, 150 C typical, with 10 C of hysteresis |
| Compensation | internal, which is why the part needs no COMP network and why the output capacitor range is limited |
Family variants and how they differ
| TPS54316 | the 3.3 V member, used where the input is 5 V and the rail is 3.3 V, which is the lowest dropout case in the family |
| Against a 12 V part | the 3 V to 6 V input is a hard limit; a 12 V bus needs a different family, not a divider |
| Fixed against adjustable | all six members are fixed output, so there is no adjustable version in this document |
| Sink capability | source and sink are both 3 A, so the part can hold a rail down as well as up, which most buck converters cannot |
| Frequency | the 350 kHz and 550 kHz settings are chosen by the FSEL pin, and the adjustable range gives 280 kHz to 700 kHz for an application that needs to move away from a beat frequency |
Points to check before this part goes on a BOM
The quiescent current is the number that dates this part. At 350 kHz the document quotes 8.4 mA typical and 12.8 mA maximum with no load, against a few tens of microamps on a modern converter. That does not matter on a mains powered board that is always on, and it matters completely on anything battery powered, so this part belongs on 5 V or 3.3 V line powered equipment and not on a portable product.
Source and sink capability at 3 A is unusual and is the reason the part survives in networking and telecom line cards. A rail that has to hold a bus termination, or a DDR rail that is pulled up by another supply, needs a converter that can absorb current without the output rising. Most synchronous bucks only sink until the inductor current reverses, and this one is specified to sink 3 A continuously.
The current limit rises with input voltage, 6.5 A at 3 V and 7.5 A at 6 V, because the limit is set by the on resistance of the switch and the peak current comparator rather than by a fixed reference. A short on the output at 5 V therefore pulls about 7 A until the thermal shutdown at 150 C removes it, and the 60 mOhm FETs are what make that survivable for the seconds it takes.
Internal compensation fixes the output capacitor range rather than leaving it open. The document's stability data is written around a specific output capacitance and ESR window, so a board that replaces a tantalum with a much larger ceramic changes the loop and can ring. The safe route is to stay inside the published window rather than to scale the capacitor up because the transient looks slow.
Where the 1.2 V member is used
A 1.2 V rail at 3 A from a 3.3 V or 5 V bus is a core supply for an FPGA, a DSP or a line card ASIC, and the 350 kHz default is chosen for efficiency rather than for size. At 1.2 V out and 3.3 V in the duty cycle is about 36 percent, which is comfortable for the part and keeps the ripple current in the inductor modest.
The 550 kHz setting halves the inductor for the same ripple, which matters when board area is tight, but the switching loss in the 60 mOhm FETs rises and the 8.4 mA quiescent current rises with it.
What the PowerPAD is for
Three amps through 60 mOhm of switch resistance is 0.54 W of conduction loss before switching, and a 20 pin HTSSOP without a thermal path cannot remove that at 85 C ambient. The PowerPAD is the exposed pad on the underside, and the document's thermal numbers assume it is soldered to a copper area with vias.
That is also why the part is specified to 125 C junction rather than to a higher figure: the package, not the silicon, sets the ceiling.
Where this order code fits
It supplies 1.2 V core rails for DSPs, FPGAs and line card ASICs from a 5 V or 3.3 V bus, including rails that have to sink current as well as source it. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Can this part run from 12 V? No. The input range is 3 V to 6 V, and 12 V exceeds the absolute maximum. A 12 V bus needs a different family.
Is the output adjustable? No. Every member of this family is fixed output, selected by the order code from 0.9 V to 3.3 V.
Why is the quiescent current so high? The control circuit draws 8.4 mA typical and 12.8 mA maximum at 350 kHz. It suits line powered equipment and not battery products.
What reel size comes with the R suffix? 2000 pieces on a large reel for the PWP body, with the T suffix for the small reel.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.