Contact Us

TPS54240DGQR

Brand: Texas Instruments
Texas Instruments TPS54240DGQR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS54240DGQR — Power Management & Signal Chain | Superb Automation

TPS54240DGQR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS54240DGQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS54240DGQR: 42 V input, 2.5 A step-down converter with Eco-mode light load behaviour

TPS54240DGQR is a wide input step-down converter that survives 42 V transients and keeps its own quiescent draw low enough for an always-on industrial rail in a HVSSOP (DGQ) body of 10 pins. It regulates down from 3.5 V to 42 V of input at 2.5 A, switches anywhere from 100 kHz to 2.5 MHz, and holds 138 uA of operating current, which is what makes it usable on a 24 V industrial rail that has to keep a standby output alive.

Order code and package

Ordering stringTPS54240DGQR, the HVSSOP body on a 2500 piece large reel
Body10 pin HVSSOP, 3.00 mm by 3.00 mm, with a PowerPAD that has to be soldered to the ground plane
Second body10 pin VSON, 3.00 mm by 3.00 mm, same die and same pinout
Addendum statusActive, production, RoHS yes, lead finish NIPDAUAG, moisture level 1 with unlimited floor life, minus 40 to 125 degrees, part marking 54240
Input range3.5 V to 42 V operating, with the internal lockout at 2.5 V
Output current2.5 A continuous with the 200 milliohm high side FET inside the package
Reference0.8 V, plus or minus 1 per cent at 25 degrees, so a 3.3 V rail needs a divider that survives the tolerance stack

Electrical parameters that decide the application

High side FET200 milliohm at 12 V in with 6 V of boot voltage, 300 milliohm at 3.5 V in with 3 V of boot
Quiescent current138 uA typical operating with no load, 200 uA maximum, in pulse skipping Eco-mode
Shutdown current1.3 uA typical, 4 uA maximum, with the enable pin low
Switching frequency100 kHz to 2.5 MHz set by a resistor on RT/CLK, and 300 kHz to 2.2 MHz when synchronised to an external clock
Frequency accuracy581 kHz typical with a 200 k resistor, inside a 450 to 720 kHz window
Current limit3.5 A minimum, 6.1 A typical, so the 2.5 A rating sits well under the valley where the part starts folding back
Enable threshold1.25 V typical, 1.15 to 1.36 V, with the pin held by an internal current source so a two resistor divider sets a custom lockout
Power goodOpen drain, asserted outside the 94 to 107 per cent window, with 2 per cent of hysteresis
Slow start2 uA charging current into the SS/TR pin, and 382 uA of discharge when the output falls away in an overload
Thermal shutdown182 degrees, with frequency foldback before the die reaches it
Soft start matchingSS/TR to reference crossover within 45 mV, which is what makes the pin usable for tracking a second rail
Temperature rangeminus 40 to 150 degrees junction, wider than the 125 degree ambient the addendum prints

Family variants and how they differ

Eco-modeBelow a threshold load the part skips pulses and drops into a low frequency burst, which is where the 138 uA comes from. The trade is output ripple at light load and a slightly softer transient response
Forced continuous optionPulling the RT/CLK pin into clock mode keeps the part switching at a fixed rate so the ripple stays predictable, at the cost of the light load current
TPS54240 against the 3 A membersThe 3.5 to 42 V family also carries 3 A and 3.5 A parts with lower switch resistance. This one is the 2.5 A member, and the current limit window is what separates them in practice
SynchronisationAn external clock between 300 kHz and 2.2 MHz locks the switching rate, which is the usual way to keep a converter out of an AM band or to beat with a neighbouring supply
TrackingThe SS/TR pin follows an external ramp, so two rails come up together or in a set ratio without a sequencer
Package differenceThe HVSSOP body and the VSON body are electrically identical; the VSON has the lower thermal resistance and the HVSSOP is easier to inspect

Points to check before this part goes on a BOM

The 42 V figure is the operating ceiling, not a transient rating. A 24 V bus with a 40 V clamp sits close enough to the limit that the input capacitor and the clamp have to be chosen together.

Eco-mode quiescent current is 138 uA typical and 200 uA maximum. On a product that must hold a rail alive for years from a battery, the maximum figure is the one that sizes the pack.

The 0.8 V reference is plus or minus 1 per cent at 25 degrees. Over temperature the divider tolerance dominates, so a 1 per cent resistor pair gives a better rail than a 0.1 per cent reference with 5 per cent resistors.

Current limit is 3.5 A minimum. A 2.5 A load with a 3.5 A floor leaves 40 per cent of headroom, which is why this part tolerates a motor or a lamp that pulls a surge at start up.

The PowerPAD is the only thermal path that matters. A 2.5 A converter at 24 V in and 3.3 V out dissipates close to a watt in the switch, and a pad with three vias is not enough.

Frequency foldback and thermal shutdown protect the part in an overload, but both are recovery mechanisms, not ratings. A board that trips them in normal operation is over-loaded, not protected.

Where the 42 V ceiling comes from

Industrial 24 V rails are specified at 24 V plus or minus 10 per cent, and a contactor or a long cable can push a surge well past 30 V. Telecom 48 V rails are outside this part's range and need a different family. The part is built for the 12 V and 24 V world with margin for the spike that arrives when a load switches off.

Above 36 V in, the switching losses in a 200 milliohm FET at 2.5 A become the limit rather than the current rating. Efficiency falls and the die heats, so a 36 V to 42 V input at full load needs the thermal pad treated as a first class component.

Where this order code fits

Industrial and telecom boards that run from a 12 V or 24 V bus and see inductive kick at the connector are the main use. The same part suits GSM and GPRS modules in fleet tracking, energy meters and security panels, where the input is a battery or a wall adapter that sags and spikes and the load is a 3.3 V or 5 V rail of a few hundred milliamps. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Can it deliver 2.5 A from 24 V in at 5 V out without a heatsink? Only with a proper thermal path. The conduction loss at 2.5 A is about 1.25 W in the high side FET alone, plus switching. A four layer board with a via field under the pad handles it; a two layer board with a small pad does not.

What sets the minimum output voltage? The 0.8 V reference and the minimum controllable on time. Outputs below 0.8 V are not possible with a divider, and very short on times at high input voltage limit how low the output can go at full frequency.

Does Eco-mode affect the start up? No. The part starts in continuous mode and only enters pulse skipping once the output is in regulation and the load is light.

How do I set a custom input lockout? Use a divider from VIN to the enable pin. The pin has an internal current source, so the thresholds are set by the resistor ratio and the 1.25 V typical threshold, and 50 mV of hysteresis comes from the current step inside the pin.

Is the VSON version a drop-in for the HVSSOP? Electrically yes, mechanically no. The pinout matches, but the pad geometry and the thermal resistance differ, so the copper under the part has to be rechecked.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.