Contact Us

TPS54202DDCR

Brand: Texas Instruments
Texas Instruments TPS54202DDCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS54202DDCR — Power Management & Signal Chain | Superb Automation

TPS54202DDCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS54202DDCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS54202DDCR: 2 A synchronous buck, 4.5 V to 28 V input, 500 kHz with spread spectrum, SOT-23-6

TPS54202DDCR is a 2 A synchronous step down converter that works from a 4.5 V to 28 V input and spreads its switching frequency to keep the emission spectrum below the limit in a SOT-23-6 body of 6 pins. The switches measure 148 milliohm on the high side and 78 milliohm on the low side. Quiescent current is 45 microamp and shutdown current is 3 microamp, which is low for a part that takes 28 V in. Control is peak current mode with internal compensation, the switching frequency is fixed at 500 kHz with spread spectrum on top, and the soft start is 5 ms internal, long enough to charge a large output bank without hitting the current limit.

Order code and package

TPS54202DDCRActive, SOT-23-THIN (DDC) body, 6 pins, 3000 pieces on a large reel, marking 4202
TPS54202DDCR.AActive, same body and same 3000 piece reel, material row at MSL Level-1-260C-UNLIM
TPS54202DDCTActive, the same body with 250 pieces on a small reel
Temperature rangeminus 40 to 125 degrees junction
Frequency behaviour500 kHz fixed with spread spectrum, which is not defeatable on this string

Electrical parameters that decide the application

Input voltage4.5 V to 28 V
Output voltage0.8 V to 24 V, set by a divider against a 0.8 V reference
Output current2 A continuous
Switch resistance148 milliohm high side, 78 milliohm low side
Quiescent and shutdown current45 microamp operating, 3 microamp in shutdown
Switching frequency500 kHz fixed, with frequency spread spectrum for emissions
Soft start5 ms internal, no external capacitor
Protectioncycle by cycle current limit on both switches, hiccup after a persistent fault, overvoltage protection and thermal shutdown

Family variants and how they differ

TPS54202the 2 A member with spread spectrum, the string on this page
TPS54302the 3 A member in the same body, same pin out and same 28 V input
Reference0.8 V, which sets the lowest usable output at the same value
Light loadAdvanced Eco-mode pulse skipping, not forced continuous
Compensationinternal, with no COMP pin brought out

Points to check before this part goes on a BOM

Twenty eight volts input is what separates this part from the rest of the family. A 24 V industrial bus at plus 10 per cent is 26.4 V and a transient on that bus can pass 28 V, so the ceiling is close but usable for a protected bus. A 24 V rail with load dump, a 48 V telecom bus or a vehicle rail is outside the rating. The part is the right answer for a 24 V industrial supply and the wrong answer for anything above it.

Spread spectrum is an emissions feature with a visible side effect. The switching frequency moves around 500 kHz instead of sitting on one point, which spreads the energy that would otherwise appear as a narrow peak in a conducted emissions scan. The cost is a small amount of output ripple at the modulation frequency, which matters on a rail feeding an analogue load. On a 24 V industrial product that has to pass an emissions test, the trade is usually worth it.

Forty five microamp of quiescent current on a 28 V part is unusual. Most wide input converters of this class draw several hundred microamp, which matters on a product that keeps a rail alive from a battery or a 24 V standby supply. At 45 microamp on a 24 V rail the converter draws about 1 milliwatt, which is small enough to leave the rail on permanently.

A 5 ms soft start is deliberately long. It lets a 470 microfarad or larger output bank charge without reaching the current limit, which keeps the input supply from seeing a step. The penalty is start up time: a rail that has to be valid within a few milliseconds cannot use this part as it stands, and the sequence has to allow for the ramp.

Peak current mode control with internal compensation is a mixed blessing. It handles a wide input range well and the loop is stable without external parts. The catch is that the internal compensation is chosen for a range of output capacitance, and a board that fits a very small or a very large output capacitor moves outside that range. The result is either a slow loop or a ringing step response, and neither shows up until the load steps.

The 0.8 V reference sets both the minimum output and the divider current. A 3.3 V output uses a divider ratio of about four, and the lower resistor is chosen so the divider draws at least a hundred times the feedback leakage. On a 24 V input with a 0.8 V output the divider is the largest load on the rail, which is a common oversight on a rail that is supposed to be efficient.

Hiccup protection on both switches is what keeps a short from destroying the inductor. The high side limit protects the input, the low side limit protects against current runaway when the inductor current does not fall to zero, and the hiccup circuit restarts after a pause. A sustained short produces a pulsing output at a low frequency, which is normal and often misread as an unstable converter.

A 148 milliohm high side at 2 A is 0.59 W at full duty. In a 12 V to 5 V rail the duty cycle is 42 per cent, so the high side dissipates about 0.25 W and the low side about 0.18 W. That is fine in a six pin SOT-23 with copper around it and marginal on a board that puts the part in a corner with narrow traces. The 24 V to 3.3 V case is easier thermally because the duty cycle is short.

Two reel sizes cover prototype and production. The R string ships 3000 pieces on a large reel and the T string 250 on a small reel. A prototype build of 200 pieces is the case for the small reel, and a distributor quoting a production quantity should confirm which packing is offered rather than assume the large reel.

What to confirm before this part goes on a purchase order

State the input bus with its worst case transient. The 28 V ceiling covers a 24 V industrial bus and not a 24 V rail with load dump.

Say whether the rail feeds an analogue load. Spread spectrum and pulse skipping both put low frequency components on the output, and a rail that has to be quiet needs a different part.

Where this order code fits

It makes a 5 V rail at 2 A from a 12 V or 24 V industrial bus, on a board that has to pass an emissions test without a large input filter. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can it work from a 24 V industrial supply? Yes, 24 V is well inside the 4.5 V to 28 V range and the part has 4 V of margin for a transient. A 24 V bus that is specified to plus 20 per cent reaches 28.8 V and is outside the range, so the supply specification has to be checked rather than assumed.

Why is the soft start so long? Five milliseconds allows a large output capacitor to charge under control instead of at the current limit. The trade is start up time. A rail that has to be valid quickly cannot use the internal ramp as it stands and the sequence has to allow for it.

Does the spread spectrum affect the output ripple? It adds a low frequency modulation on top of the 500 kHz ripple, with an amplitude that depends on the output capacitor and the load. On a digital rail it is invisible. On a rail feeding a measurement front end it can appear inside the band of interest.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.