Contact Us

TPS54116QRTWRQ1

Brand: Texas Instruments
Texas Instruments TPS54116QRTWRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS54116QRTWRQ1 — Power Management & Signal Chain | Superb Automation

TPS54116QRTWRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS54116QRTWRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS54116-Q1 automotive buck plus DDR termination regulator in one 4 mm package

The TPS54116QRTWRQ1 is a single chip power solution for a DDR2, DDR3 or DDR3L memory rail in an automotive board. It holds two regulators that are normally two separate parts: a 4 A synchronous buck that makes the VDDQ rail from a 2.95 V to 6 V input, and a 1 A source and sink linear regulator that makes the VTT termination rail at half of VDDQ. A 10 mA buffered reference output, VTTREF, tracks VDDQ at 49 to 51 per cent and is what the memory controller uses as its reference. Putting all three functions in a 24 pin 4 mm by 4 mm WQFN removes the tracking error that appears when the buck and the termination rail come from different parts with different references.

The device is AEC-Q100 qualified at grade 1, which is minus 40 to plus 125 degrees ambient, with the junction allowed to reach 150 degrees. That grade is the reason the part appears in instrument clusters, telematics units and infotainment head units, where the board sits behind a display and sees the cabin temperature rather than a conditioned rack.

Key parameters taken from the SLVSCO3B document

Input rangeAVIN and PVIN 2.95 V to 6 V, with an internal UVLO that releases at 2.7 V to 2.8 V on a rising input and 50 mV to 120 mV of hysteresis
Buck rating4 A continuous from a synchronous stage with 33 milliohm high side and 25 milliohm low side switches
Switching frequency100 kHz to 2.5 MHz, set by a resistor and synchronisable to an external clock, fixed across the load range because the low side switch stays synchronous
Reference0.6 V with 1 per cent over temperature
Termination regulator1 A source and sink, 20 mV of DC accuracy, stable with 2 by 10 microfarad of ceramic output capacitance
Reference outputVTTREF 10 mA source and sink, regulated to within 49 to 51 per cent of VDDQ
Quiescent current1 microamp typical and 3.5 microamp maximum in shutdown, 650 to 800 microamp with both regulators on, 190 to 300 microamp with only the termination regulator on
Enable pinsENSW and ENLDO separate, 1.20 V rising and 1.17 V falling, 2.7 microamp of hysteresis current for a resistor divider
ProtectionAdjustable cycle by cycle peak current limit on the buck, thermal shutdown, and both VTT and VTTREF discharged when ENLDO is low
Package24 pin WQFN, 4 mm by 4 mm, thermally enhanced

Why the switching frequency matters in a car radio

The buck can be set above the medium wave broadcast band. That single sentence explains a lot of automotive memory rail choices: an AM receiver in the same enclosure will pick up a 400 kHz switching harmonic as a whistle on a weak station, and moving the clock to 2 MHz or above puts the first harmonic outside the band the tuner cares about. The part also accepts an external clock, so several rails on one board can be locked to a common source and the beat note between them disappears. For a telematics unit that has both a cellular modem and an AM or FM tuner, this is usually the deciding feature.

Board arrangement and thermal points that decide the current rating

The 4 A rating belongs to the silicon, not to the board. The WQFN pad has to be soldered to a copper area with vias, and the vendor's thermal figures assume a board with copper on both sides. At 5 V in and 1.35 V out the duty cycle is short, so the low side switch conducts most of the time and its 25 milliohm dominates the conduction loss; at 3.3 V in the high side conduction share rises and the 33 milliohm becomes the larger term. Keeping the input capacitor within a few millimetres of PVIN and the ground pad is the difference between a rail that holds 4 A at 105 degrees and one that folds back at 2.5 A.

The VTT output needs its own 10 microfarad ceramic at the memory devices as well as the 2 by 10 microfarad at the regulator, because the termination current is bidirectional and the loop has to see the capacitance at the load. The vendor states stability with the 2 by 10 microfarad figure, which is a low output capacitance for a 1 A linear regulator and is one of the reasons the part saves space against a discrete solution.

Where this part is used and what to check on a quote

The typical socket is a DDR3L rail in an automotive cluster or a telematics module, at 1.35 V VDDQ with a 0.675 V VTT and a reference at the same level. The part also appears in industrial boards that need a memory rail and want one reference domain, though the AEC-Q100 grade is what most customers are paying for.

Two ordering details deserve a check. The reel suffix distinguishes the large reel from the small reel on the same body, and the suffix on a distributor line is not always the one on the drawing. The other is the grade: an automotive part and an industrial part can share a datasheet family and differ only in the temperature qualification, so the qualification record should be requested with the quote. Our desk keeps the AEC-Q100 record with the part and lists the memory rail options on memory cross reference, and the broader power portfolio is on power management cross reference.

What a customer usually asks next

The first question is whether the termination rail can be left off when the memory is soldered down and does not need VTT. The answer is yes, ENLDO keeps that regulator off and the buck runs alone, which is why the quiescent current table has a row for the buck only. The second is whether the two enables can be tied together. They can, with the caveat that the combined input current changes, and the vendor gives that row too. The third is the start up order: the buck should be up before the termination rail, and the resistor dividers on the two enable pins are how that order is set without a sequencer. For a board that already has a supervisor, the simpler route is to drive both enables from it and let the internal soft start handle the ramp.