Contact Us

TPS54062DGKR

Brand: Texas Instruments
Texas Instruments TPS54062DGKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS54062DGKR — Power Management & Signal Chain | Superb Automation

TPS54062DGKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS54062DGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS54062DGKR: 50 mA synchronous step-down converter from 4.7 V to 60 V with an 89 uA quiescent current

TPS54062DGKR is the lowest current member of the 60 V synchronous buck family, built to hold a bias rail alive from a high voltage bus at tens of milliamps in a MSOP body of 8 pins. The TPS54062 converts 4.7 V to 60 V to an adjustable output at up to 50 mA, with both MOSFETs inside the package and a switching frequency adjustable from 100 kHz to 400 kHz. Quiescent current is 89 uA and shutdown current is 1.7 uA, and the reference is 0.8 V with two percent accuracy. The switch resistance is 0.8 Ohm at a 12 V input and 1.5 Ohm with a 5.7 V boot charge, which is what a 50 mA part looks like: the switches are small because the current is small.

Order code and package

Order codeTPS54062DGKR
Input voltage4.7 V to 60 V
Output current50 mA
Reference0.8 V, 0.784 V to 0.816 V
Switching frequency100 kHz to 400 kHz, adjustable
Quiescent current89 uA typical, 110 uA maximum at 12 V in
Shutdown current1.7 uA
Switch resistance0.8 Ohm typical at 12 V in, 1.5 Ohm typical with a 5.7 V boot charge
Package8 pin MSOP with an exposed pad
Start voltage4.53 V typical, rising
Enable to switching450 us
External clocksynchronises to an external source
DocumentSLVSAV1D, May 2011, revised July 2016

Electrical parameters that decide the application

Thermal resistance, MSOP127.1 C per W junction to ambient
Thermal resistance, VSON40.2 C per W junction to ambient
Junction range-40 C to 125 C
Error amplifier transconductance102 uS
Soft-start transconductance26 uS with the sense pin at 0.4 V
Enable hysteresis current-4.7 uA at plus 50 mV, -1.2 uA at minus 50 mV
Output capacitorceramic or low cost aluminium electrolytic
Current limitcycle by cycle, with frequency foldback
Light loaddiode emulation for efficiency
Reference accuracyplus or minus 2 percent
Protectionthermal shutdown and frequency foldback
Frequency range100 kHz to 400 kHz, set by a resistor

Points to check before this part goes on a BOM

Fifty milliamps is the whole market for this part: a housekeeping rail that must exist before the main converter starts, or a bias supply for a gate driver. At that current the switches can be small, which is why the on resistance is 0.8 Ohm rather than tens of milliohms, and why the loss at 50 mA is only a few tens of milliwatts.

The two package options have very different thermal behaviour, and the part number decides which one is ordered. The MSOP body is 127.1 C per W and the VSON is 40.2 C per W, three times better, which matters at a 60 V input where the loss is dominated by the switch and the internal housekeeping. A board that runs at a 70 C ambient inside an enclosure should take the VSON even though the MSOP is easier to inspect.

Eighty nine microamps of quiescent current is what keeps a standby rail honest. A 48 V bus that feeds a permanently enabled 3.3 V bias supply will draw that current for the life of the product, and at 89 uA a year is under 0.8 mAh of charge, which is negligible. The same rail built around a converter with 1 mA of quiescent current would cost 8.8 Ah a year, which is not.

The 0.8 V reference with two percent accuracy is looser than the parts used for processor cores, and that is deliberate. A bias rail does not need one percent, and the looser reference costs less. A board that needs a tight 3.3 V for an analog reference should not use this rail directly, and should either post regulate or take the measurement ratiometrically.

Frequency foldback is the protection that keeps a shorted output from destroying the part. When the current limit is reached the oscillator slows, so the inductor has more time to reset and the current does not keep climbing. On a 60 V input the foldback also reduces the switching loss during the fault, which is what buys the thermal shutdown time to act.

Diode emulation makes the light load behaviour discontinuous, and the output ripple in that mode is larger than the continuous figure. On a bias rail feeding a microcontroller this is invisible; on a rail feeding an analog reference it is not, and a small preload resistor is often the cheapest fix.

Synchronising to an external clock is available and is worth using where the board has several converters. A 400 kHz clock shared across the board keeps the beat products out of the measurement band and makes the input filter predictable rather than a set of experiments.

Where this order code fits

This order code fits bias and standby supplies in high voltage industrial equipment: a 5 V rail for a microcontroller in a 48 V motor drive, a 3.3 V rail in a metering product, and housekeeping supplies that run from a bus that is already present. Where the load is tens of milliamps and the input is a 48 V bus, this family keeps the part count low. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

What is the difference between the two package options? The MSOP body has 127.1 C per W and the VSON 40.2 C per W. The electrical behaviour is the same, and the thermal margin is not.

Can it run from a 60 V bus continuously? The operating range ends at 60 V, so the steady state has to stay inside that with margin for the bus tolerance and the transients.

Is the output adjustable? Yes, from the 0.8 V reference upward, set by an external divider.

SUPERB quotes this order code with date codes and packing on the offer, and the BOM Shortage Recovery page covers the checks for a high voltage bias rail that has to stay available.