TPS5403DR
Product Specifications
TPS5403DR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS5403DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS5403DR: 1.7 A non-synchronous step-down regulator with a fixed 3.3 V output from 4.5 V to 28 V
TPS5403DR is a 28 V input buck regulator with an integrated high-side switch, a fixed 3.3 V output and a programmable frequency from 50 kHz to 1100 kHz in a SOIC body of 8 pins. The TPS5403 converts 4.5 V to 28 V to a fixed 3.3 V at up to 1.7 A using a single integrated high-side switch and an external diode, which is what makes it a non-synchronous part. It uses current mode control with internal slope compensation, sets its switching frequency with one resistor from 50 kHz to 1100 kHz, and defaults to 120 kHz when that resistor is left open. The high-side switch is 120 mOhm typical, peak current limit is 2.5 A typical, maximum duty cycle is 93 percent, and the body is an eight pin SOIC.
Order code and package
| Order code | TPS5403DR |
| Input voltage | 4.5 V to 28 V |
| Output voltage | 3.3 V fixed, 3.2 V to 3.4 V at 12 V in |
| Output current | 1.7 A |
| Switch | one integrated high-side MOSFET, external catch diode |
| High-side resistance | 120 mOhm typical, 240 mOhm maximum at 12 V in |
| Switching frequency | 50 kHz to 1100 kHz, set by ROSC |
| Default frequency | 120 kHz with ROSC open |
| Peak current limit | 2.2 A minimum, 2.5 A typical, 3.1 A maximum |
| Maximum duty cycle | 93 percent |
| Minimum on time | 200 ns |
| Package | 8 pin SOIC |
| Document | SLVSBK5, September 2012 |
Electrical parameters that decide the application
| Quiescent current | 100 uA non-switching with the feedback above 3.5 V |
| Input UVLO | 3.5 V rising |
| Transconductance | 9 A per V from the compensation pin to the inductor current |
| Soft-start charge current | 2 uA |
| Error amplifier output current | plus or minus 7 uA at 100 mV overdrive |
| Frequency jitter | plus or minus 6 percent at 12 V in, used to spread emissions |
| PWM ramp swing | 1/512 of the input, at 12 V in |
| Thermal trip | 165 C rising |
| Ambient range | -40 C to 125 C |
| Output tolerance | 3.2 V to 3.4 V at a 12 V input, over the rated load |
| Diode requirement | external catch diode rated for the peak current and the input voltage |
| Feedback | internal divider, the sense pin monitors the output directly |
Points to check before this part goes on a BOM
Non-synchronous means the catch diode is on the board, and that diode is where the efficiency goes. At 1.7 A and 3.3 V out from a 12 V input, the diode conducts for about 70 percent of the period, so a Schottky with a 0.4 V forward drop dissipates close to half a watt. A board that compares this part with a synchronous converter should add that loss to the budget before it concludes anything about the regulator.
The 93 percent maximum duty cycle is the dropout limit. A 5 V input producing 3.3 V needs 66 percent, so there is room, but a 4.5 V input at the bottom of the range needs 73 percent, and a load transient that pulls the input down further will push the part into its minimum off time. On a 24 V rail the duty cycle is 14 percent, and the 200 ns minimum on time then sets the practical limit on how high the input can go at 3.3 V out.
Frequency is a direct trade between inductor size and loss. At 50 kHz the inductor is large and the switching loss is low, which suits a board where the parts budget is bigger than the space budget; at 1100 kHz the inductor is small and the diode and switch losses climb. The default 120 kHz with the resistor open is a reasonable compromise for a 24 V rail and a 1.7 A load.
The plus or minus 6 percent jitter is there for emissions, not for accuracy. It spreads the switching energy over a band instead of concentrating it at one harmonic, which helps a product pass a conducted emission test without a larger input filter. A board that needs a stable switching frequency for another reason, for example to avoid a beat with a sampling clock, should take that into account.
Current mode control with internal slope compensation fixes the inductor value range. The compensation ramp is matched to a particular inductance and output capacitance, and a board that replaces the inductor with a much smaller value can see sub-harmonic oscillation at high duty cycle. When a substitute is considered, the inductor and the compensation network are part of the comparison, not just the part number.
The 1.7 A rating and the 2.2 A minimum peak limit leave a narrow margin on purpose. In a non-synchronous buck the inductor current is continuous and the peak is the output current plus half the ripple, so a 1.7 A load with 40 percent ripple sits at 2.04 A peak, just under the minimum limit. A larger ripple trips the limit before the rated current is reached.
An eight pin SOIC is a relief on a repair line. The leads are visible, the joints can be inspected without an x-ray, and the part is easy to replace in a 24 V industrial product that is serviced rather than scrapped. That is a large part of why this family stays in production builds even though newer parts are smaller.
Where this order code fits
This order code belongs on 12 V and 24 V industrial rails that need a fixed 3.3 V housekeeping supply at a bit over an amp: relay and sensor boards, building control equipment, motor drive logic supplies and instrumentation that runs from a 24 V bus. The 28 V input ceiling leaves margin for a nominal 24 V rail with normal tolerance. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Obsolete RF Part Replacement page.
Questions buyers ask
Is the output adjustable? No. The TPS5403 is the fixed 3.3 V member and its sense pin monitors the output directly, so there is no external divider to change.
What diode does it need? An external Schottky rated for the 2.5 A peak current and the 28 V input, with a low forward drop, because the diode carries the inductor current for most of the period.
Why is the frequency jittered? To spread switching energy across a band and make conducted emissions easier to pass. It is not an accuracy specification.
SUPERB quotes this order code with date codes and packing on the offer, and the Component Lead Time Solutions page sets out the substitution checks for a fixed output regulator in a long life industrial board.