TPS53667RTAt
Product Specifications
TPS53667RTAt
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS53667RTAt from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS53667RTAt: the six phase controller for ASIC and point of load rails
TPS53667RTAt is a six phase step-down controller built for high current point of load rails, with a serial interface for telemetry and non volatile memory for its configuration. It is the member of the family that carries the widest phase count, so a single body can drive six power stages in parallel and hold a rail that would otherwise need two controllers and an interleaving scheme between them. The stages it drives are the CSD9549x NexFET family, and the controller is written to be compatible with them rather than with an arbitrary stage.
The tail in our catalogue is printed with a lower case t, which is a spelling the vendor addendum does not use. The addendum prints two rows for this device: TPS53667RTAR on a 2000 piece large reel and TPS53667RTAT on a 250 piece small reel, both in the same 40-pin WQFN body. The lower case letter on our page is the catalogue's rendering of the small reel tail, and the reel quantity is confirmed on the purchase order rather than inferred from the string.
The numbers below come from SLUSC40B, revised February 2017, and from the addendum: the boot voltage range and step, the conversion range, the frequency window, the phase count, the current limit levels and the thermal and moisture data for the 6 mm body.
What the order code sits on
| Function | six phase step-down controller, driverless, with non volatile memory |
| Phase count | one, two, three, four, five or six phases |
| Boot voltage | 0.5 V to 2.5 V, 8 bit selection, 5 mV steps, by pin strap or memory |
| Conversion range | 4.5 V to 17 V input |
| Switching frequency | 300 kHz to 1 MHz with closed loop frequency control |
| Power stages | CSD9549x NexFET stages |
| Current limit | 16 levels per phase, set by pin strap or memory |
| Transient | 8 independent levels of overshoot reduction and undershoot reduction |
| Phase management | dynamic phase shedding with a programmable current threshold |
| Balancing | phase current imbalance detection and reporting, autobalance |
| Bias | 1.8 V and 3.3 V PMBus bias compatible |
| Package | WQFN, 40 pins, 6 mm by 6 mm, thermal pad |
| Reel | 2000 pieces on the large reel, 250 on the small reel |
| Lead finish | NIPDAU |
| Moisture level | Level-2-260C-1 YEAR |
| Operating temperature | minus 40 to plus 125 degrees |
Six phases and the current a single rail can carry
The reason to put six phases on one controller is current. A single stage in this family carries tens of amps, and six in parallel with proper phase interleaving gives a rail in the hundreds of amps with ripple that is a fraction of what one phase at the same total current would produce. The interleaving is what makes the input and output capacitors smaller, because the ripple currents of the phases cancel at the switching node rather than adding.
The autobalance function is what keeps six phases from becoming one hot phase and five cool ones. Each phase reports its current, the controller adjusts the on time of each to bring them together, and the imbalance is reported so a fixture can see it. A board with a stage that has drifted will show a current report that is out of line before the stage fails, which is the difference between a scheduled replacement and an unplanned outage.
Phase shedding works in the other direction. At light load the controller turns phases off so the remaining ones run at a higher fraction of their rating, and the threshold is programmable and stored. On a point of load rail that idles at a few amps out of a hundred, the shedding is what keeps the efficiency from collapsing at idle, and on a rail that never idles it does nothing.
The boot voltage and the 5 mV step
The eight bit boot voltage selection covers 0.5 V to 2.5 V in 5 mV steps, and the value can come from a pin strap or from non volatile memory. The pin strap route lets a board set its rail without any host interaction, which is what a point of load rail needs at power up before a processor is running. The memory route lets the same board be reprogrammed for a different rail without changing a strap, which is what a test fixture uses.
A 5 mV step on a 0.9 V rail is about half a percent, so the boot voltage can be set within a fraction of a percent of the target without an external divider. The accuracy of the setting is a separate matter from the step size: the reference and the feedback path set the absolute accuracy, and the data sheet prints those terms separately rather than folding them into the resolution.
The 0.5 V to 2.5 V window is wider than the VR13 processors need, and that is deliberate. A point of load rail for an ASIC, an FPGA core or a memory rail can sit anywhere in that window, so one controller serves several sockets on the same board with different strap settings rather than needing a different device per rail.
Telemetry and the bias arrangement
The PMBus interface reports voltage, current, power, temperature and fault conditions, and it accepts both 1.8 V and 3.3 V bias, which is what allows it to sit on a board whose management bus is at either level. The 1.8 V option matters on dense boards where the management controller runs at 1.8 V and a level shifter would add parts and capacitance to the bus.
Fault reporting covers output voltage, output current and temperature, and each is a separate status bit rather than a single fault line. A baseboard controller that reads those bits can tell an over temperature event from a short, which is what a service log needs. The same interface carries the configuration, so a factory calibration written once is inherited by every board afterwards.
The thermal pad on the 6 mm body is the return for the gate drive, and the via pattern under it decides whether the drive signals ring. Six phases switching at up to 1 MHz in one body produce a lot of edge current, and a pad connected through a sparse via array will show ground bounce on the current sense inputs. The data sheet gives the pattern, and the failure mode of ignoring it is a current report that jumps by tens of amps on some boards.
Carriers, reels and reel geometry
| TPS53667RTAR | WQFN RTA, 40 pins, 2000 pieces, large reel, active |
| TPS53667RTAT | same body, 250 pieces, small reel |
| Catalogue string | TPS53667RTAt, lower case t, normalises to the small reel row |
| Reel geometry | 330 mm reel, 16.4 mm width, 6.3 mm pocket |
| Lead finish | NIPDAU, nickel palladium gold |
| Moisture level | Level-2-260C-1 YEAR, one year floor life |
| Operating temperature | minus 40 to plus 125 degrees |
| Part marking | TPS53667 across two lines |
| Body | 6 mm by 6 mm with thermal pad |
The 2000 piece large reel is smaller than the 3000 piece reels on the neighbouring controllers, and that is a function of the body size: a 6 mm part takes more pocket area, so a standard reel holds fewer. A line that plans its run rate from a 3000 piece reel will find this part runs out a third sooner, which matters when the run is continuous and the reel change is a line stop.
Where this controller fits
The applications the vendor prints are ASIC power in communications equipment and high current point of load rails, and the six phase arrangement is what those rails need. A switch ASIC, a network processor or an FPGA core that draws more than a single stage can supply is the case this part was written for, and the CSD9549x stages are the ones it is specified against.
For a customer the first question is usually whether the stages are still available, because the controller is useless without them. The second is the phase count, because a board wired for four phases cannot use the sixth even when the controller supports it. Both fields, plus the boot voltage window and the PMBus bias level, are what a substitution has to match, and they are listed on our power management cross reference page. When the original string is out of production, the obsolete part cross reference hub covers what a replacement has to prove before a board change is justified.
Questions buyers ask before a first order
How many stages can it drive? Up to six, one per phase, and the phase count is set by configuration rather than by a separate device.
Does it need a host to start? No. The boot voltage and the current limit can come from pin straps, so the rail comes up without any bus traffic.
Is the reel quantity 3000? No. This body takes 2000 pieces on the large reel and 250 on the small reel, which is fewer than the 5 mm controllers in the same family.
What bias does the PMBus need? Either 1.8 V or 3.3 V, which lets the part sit on a management bus at either level without a shifter.