Contact Us

TPS53317RGBR

Brand: Texas Instruments
Texas Instruments TPS53317RGBR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS53317RGBR — Power Management & Signal Chain | Superb Automation

TPS53317RGBR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS53317RGBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS53317RGBR: 6 A source and sink synchronous converter for DDR memory termination

TPS53317RGBR is a FET-integrated synchronous buck regulator with D-CAP+ control built to sink and source the termination current of a DDR memory bus in a VQFN (RGB) body of 20 pins. It regulates a termination rail at half the memory supply, sources and sinks up to 6 A, and runs from 1 V to 6 V with an output adjustable from 0.6 V to 2 V, which is the range a DDR3, DDR3L or DDR4 termination node needs.

Order code and package

Ordering stringTPS53317RGBR, RGB package, 3.5 mm by 4 mm 20-pin VQFN, tape and reel
Family roleA DDR termination regulator, also usable as a 6 A point of load converter
Package20-pin VQFN, 3.50 mm by 4.00 mm, with exposed pad
Sink capabilityFull 6 A sink as well as source, which a buck converter alone cannot do
TrackingExternal tracking input, so the rail can follow half the memory supply
MODE pinFour threshold bands select frequency, skip mode and current limit

Electrical parameters that decide the application

Input range1 V to 6 V conversion voltage
Output range0.6 V to 2 V, adjustable
Output current6 A continuous in both directions
Switching frequency600 kHz or 1 MHz, selectable
Control modeD-CAP+ with external tracking and optional droop
Output capacitorsCeramic, polymer or SP-CAP, all supported
ProtectionsOver voltage, over temperature, hiccup under voltage, selectable over current
StartupPre-bias safe, with output soft discharge and an internal bootstrap switch

Points to check before this part goes on a BOM

Termination is a two quadrant job. A DDR bus has to be held at half the supply while the memory both draws and returns current, so a converter that can only source will let the rail rise every time the bus turns around, and the usual symptom is a memory error that appears only under a particular access pattern. The 6 A sink rating and the loop that regulates in both directions are the reason this part exists rather than a generic 6 A buck.

The 1 V minimum input is a real constraint on a DDR3L system where the memory rail is 1.35 V. The termination converter runs from that rail, so its input headroom is only 350 mV above the 0.675 V output, and the duty cycle needed is 50 percent, which is comfortable. On a DDR4 rail at 1.2 V the output is 0.6 V and the duty is again 50 percent, so the part is inside its range, but a rail that sags to 1.0 V leaves almost no headroom for the switch resistance.

Droop is optional and it is a memory signal integrity decision rather than a power decision. With droop enabled the output voltage falls slightly as the source current rises, which reduces the overshoot when the bus current steps and lets the capacitor bank be smaller. With droop disabled the rail is flat, which is what a test fixture wants when it is measuring the regulator and not the memory.

The MODE pin selects between four combinations of frequency, skip mode and current limit, so a single strap changes three behaviours at once. A board that sets MODE for 1 MHz and then finds the light-load efficiency poor has also changed the current limit, and the fault will be read as a board problem because the resistance and the inductor did not change. Reading the mode table before changing the strap is cheaper than reworking the board.

Sinking 6 A into the low side FET means the loss does not disappear when the current reverses. In a sink event the low-side switch carries the current and the inductor current flows the other way, so the dissipation is the same as a source event at the same magnitude and the thermal pad has to be sized for the worst direction, which in a memory test pattern is usually the sink.

External tracking is what makes the rail follow the memory supply without a second reference. The tracking input is divided from the memory rail, so the termination voltage stays at the midpoint even if the memory supply is adjusted for margin testing. A fixture that sweeps the memory rail from 1.14 V to 1.26 V will sweep the termination rail with it, and that behaviour comes from the tracking pin rather than from the regulation accuracy.

The valley current limit is what sets the real ceiling on the load. A 6 A output with a 1 microhenry inductor at 600 kHz and a 1.2 V input carries ripple of a few hundred milliamps, so the peak is close to the average and the limit is comfortably above the rating. At 1 MHz the ripple halves and the margin grows, but the switching loss doubles, and the trade between the two settings is what the frequency strap is really choosing. A board that is limited by thermals should run at 600 kHz, and a board that is limited by transient response should run at 1 MHz.

Where this order code fits

It is the termination regulator for DDR, DDR2, DDR3, DDR3L and DDR4 memory in servers, network equipment, industrial computers and test boards, and it is also used as a 6 A point of load converter where a rail has to sink current as well as supply it. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop BOM Sourcing page.

Questions buyers ask

Can it be used as a normal buck converter? Yes, for loads up to 6 A that do not need the sink capability, and the tracking input can be left at a fixed divider if the output is not following another rail.

Why does the part need a 20-pin package for 6 A? Because both FETs, the bootstrap switch, the current sense and the tracking input are inside the body, and the pad has to carry the heat of a 6 A sink event.

Does it require a minimum load? No. The loop regulates at zero load in both directions, which is what a termination rail needs when the memory is idle.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Strategic Sourcing page sets out the checks that keep a substitute from failing on the bench.