Contact Us

TPS53313RGER

Brand: Texas Instruments
Texas Instruments TPS53313RGER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS53313RGER — Power Management & Signal Chain | Superb Automation

TPS53313RGER

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS53313RGER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS53313 6 A step down regulator with the switches inside a 4 mm body

The TPS53313RGER is a complete 6 A synchronous buck converter in a 24 pin 4 mm by 4 mm VQFN, with both power MOSFETs, the bootstrap switch and the control loop inside the package. It takes a conversion input from 4.5 V to 16 V and produces an output from 0.6 V up to 0.7 times the input, which is the range that covers a 5 V or a 12 V rail feeding a 1.0 V, 1.2 V or 3.3 V load.

The part runs voltage mode control at a switching frequency programmable from 250 kHz to 1.5 MHz by a resistor, and it can be synchronised to an external clock so several converters on one board share a clock and do not beat against each other. Skip mode and forced continuous conduction are both selectable, which is the choice between light load efficiency and constant ripple.

Key parameters taken from the SLUSAS8A document

Conversion input4.5 V to 16 V, so a 12 V rail with a transient has margin and a 5 V rail works at the low end
Output0.6 V to 0.7 times VIN, adjustable, which at a 12 V input gives up to 8.4 V and at 5 V gives up to 3.5 V
Current6 A continuous, with a selectable peak current limit of 4.5 A, 6 A or 9 A
Switching frequency250 kHz to 1.5 MHz, set by a resistor on RT/SYNC, and synchronisable to an external clock
Soft startSelectable 1 ms, 3 ms or 6 ms, so a rail can be ramped slowly without an external capacitor
Output capacitorSupports all MLCC banks, so the output can be ceramic only with no bulk electrolytic
Current sensingRDS(on) sensing for both zero crossing detection and overcurrent, so there is no shunt
ProtectionOvercurrent, overvoltage and undervoltage with hiccup, plus overtemperature and a soft stop discharge on disable
Package and thermal24 pin VQFN 4 mm by 4 mm, 44.1 degrees per watt junction to ambient, minus 40 to plus 85 degrees ambient
Abs maximum18 V on the input, 20 V on the enable pin, 150 degrees junction

Choosing between skip mode and forced continuous conduction

Skip mode turns off the low side FET when the inductor current would go negative, which raises the efficiency at light load and lets the output ripple grow while the converter skips cycles. Forced continuous conduction keeps the low side FET on for the full off time, so the inductor current goes negative at light load, the output stays in a tight window and the efficiency drops by a few points.

The choice is not cosmetic on a measurement instrument. A converter in skip mode has an output ripple that depends on the load, and a rail that feeds an analog front end will show that ripple as noise that changes with the digital activity on the same board. Forced continuous conduction costs efficiency and gives a ripple that a filter can be sized against.

Where the TPS53313 belongs on the board

  • Point of load rails on 12 V backplanes, where 6 A covers a memory bank or an FPGA auxiliary rail
  • Instruments that need a quiet 3.3 V analog rail and can accept forced continuous conduction
  • Telecom boards that need several rails synchronised to one clock to keep the beat frequencies out of band
  • Industrial controllers with a 5 V bus, where the 4.5 V minimum input leaves margin for a bus dip
  • Boards that need a defined discharge on shutdown, since the soft stop function is built in

Order code, package and thermal limits

TPS53313RGER24 pin RGE VQFN, 4.00 mm by 4.00 mm, large reel, active and in production
DissipationAt 6 A from 12 V to 1.2 V the switches dissipate roughly 1.5 W, and the 44.1 degrees per watt figure needs the thermal pad soldered to a plane with vias
Inductor choiceThe 0.7 times VIN ceiling on the output means the inductor sees the full input voltage during a short, so the saturation current has to cover the 9 A limit setting
BootstrapInternal switch, so no external bootstrap diode or capacitor on the high side

Sourcing notes for this line

Integrated converters in a 4 mm body are the parts that disappear from the shelf first when a platform ramps, because the same silicon goes into consumer boards. The comparison starting point is the power management cross reference, which lists the 6 A converters that share the RGE footprint and the ones that need a different inductor.

Where a substitute is proposed, the two rows to check are the peak current limit settings and the soft start options, since a part with a fixed 5 A limit will not carry a 6 A load. The how to verify a drop in replacement page treats those rows as the first gate.

For volume programmes the reel and the moisture level decide whether a part can go straight to the line, and the component lead time page sets out the re-reel and cut tape options.

Questions buyers ask about this part

Does it need an external driver? No. Both MOSFETs and the bootstrap switch are inside, so the external parts are the inductor, the input and output capacitors, the feedback divider and the frequency resistor.

Can the frequency be changed after the board is built? Yes, within the resistor range of 250 kHz to 1.5 MHz, because the setting is a resistor value and not a factory option.

What is the 0.7 times VIN limit for? It is the maximum duty cycle the control loop allows. A rail that needs more than 70 % duty at the nominal input cannot be produced by this part, and a 5 V to 3.3 V rail sits at 66 % and is inside the window.

Does hiccup protection latch off? No. It retries until the fault clears, which is what a board with a hot plug connector needs.