TPS51396RJER
Product Specifications
TPS51396RJER
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS51396RJER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS51396RJER: the 8 A synchronous buck in a 3 mm body
TPS51396RJER is a synchronous step down converter in the twenty pin HotRod VQFN body at 3 mm by 3 mm, on a 3000 piece reel. The device takes 4.5 V to 24 V in, delivers up to 8 A continuous at an output between 0.6 V and 7 V, and switches at 600 kHz, 800 kHz or 1 MHz depending on how the mode pin is tied.
SLVSEY3C, revised April 2021, is the document behind the family, and it publishes the A suffix rows: TPS51396ARJER on a 3000 piece reel and TPS51396ARJET on a 250 piece reel. The string on this page carries no A suffix, which is a difference a buyer should resolve against the vendor's orderable list before a production release, because the datasheet in hand does not print a row for it.
What follows is what the control loop does without external compensation, the rows that decide an 8 A rail, the thermal arithmetic in a 3 mm package, and the practical meaning of the missing A suffix.
What the control scheme removes from the board
The part uses a D-CAP3 control loop, which is a ripple based scheme with internal ripple generation. That means no external compensation network, no feedback divider for the loop and no requirement for a large ESR output capacitor: the loop is stable with ceramic output capacitors, which is the opposite of what a voltage mode converter of the same current class needs.
| Orderable code on this page | TPS51396RJER, no A suffix |
| Rows printed in the datasheet | TPS51396ARJER, 3000 pieces on a large reel, and TPS51396ARJET, 250 pieces |
| Body | VQFN HotRod, 20 pins, 3.00 mm by 3.00 mm |
| Input voltage range | 4.5 V to 24 V |
| Output voltage range | 0.6 V to 7 V |
| Continuous output current | 8 A |
| Feedback accuracy at 25 degrees | 1 percent |
| High side switch resistance | 19.5 milliohms |
| Low side switch resistance | 9.5 milliohms |
| Switching frequency options | 600 kHz, 800 kHz, 1 MHz, set by the mode pin |
| Light load modes | Eco mode or out of audio mode, set by the mode pin |
| Soft start | 1.3 ms internal, extendable with a capacitor on the SS pin |
| Protection | over voltage, under voltage, over current cycle by cycle, over temperature, under voltage lockout |
| Over voltage threshold | 126 percent of the reference |
| Output discharge resistance | about 420 ohms, built in |
| Operating junction temperature | minus 40 to 125 degrees |
| Moisture rating, 3000 piece reel | level 1 on the A row, level 2 on the 250 piece small reel |
The rows that decide an 8 A rail
The two switch resistances set the conduction loss. At 8 A the high side FET conducts for the duty cycle, which on a 12 V to 1.2 V rail is 10 percent, so the high side loss is 8 squared times 19.5 milliohms times 0.1, which is 1.25 W. The low side conducts for the other 90 percent at 9.5 milliohms, which is 8 squared times 9.5 milliohms times 0.9, or 5.5 W. Those two figures are why a 12 V to 1.2 V rail at 8 A is a hard thermal case and why the same part at 12 V to 5 V, with a 42 percent duty cycle, is far easier.
Switching loss adds to that and scales with the frequency. At 800 kHz a 12 V input with 8 A of output and a 20 nanosecond transition contributes roughly 1.5 W across the two switches, so the total dissipation at 1.2 V out sits near 8 W, which is beyond what a 3 mm package holds without a heavy plane. The realistic ceiling for this body in still air is around 3 W, so a 12 V to 5 V rail at 6 A is comfortable and a 12 V to 1.2 V rail at 8 A is a rail that needs airflow.
The 1 percent feedback accuracy at 25 degrees is a room temperature figure. Over the window the reference moves, and the output tolerance for a 1.2 V rail is therefore wider than 1 percent in a hot enclosure. A rail that feeds a core at 1.2 V with a plus or minus 3 percent window has room, and a rail that feeds a 0.9 V core with a plus or minus 2 percent window does not, which is the case where a converter with a tighter reference is the right part.
The mode pin and light load behaviour
The mode pin selects both the frequency and the light load behaviour, which is unusual and useful. Tying it one way gives Eco mode, where the converter reduces the switching frequency at light load and holds efficiency; tying it the other way gives out of audio mode, where the converter keeps switching above 25 kHz so that a ceramic output capacitor and an inductor do not sing in the audible band.
That second option exists for consumer equipment that sits in a quiet room. An audio product with a light load rail that drops into the audible band will produce a whistle that no amount of shielding fixes, and the fix is the mode pin rather than a component change. For an industrial product the Eco mode is the right choice because the standby efficiency is worth more than the acoustic behaviour.
The internal soft start of 1.3 ms is fast enough for a point of load rail and slow enough to keep the inrush inside the current limit on most boards. A rail with more than about 500 microfarads of output capacitance needs the SS capacitor, because the internal ramp will otherwise finish before the output reaches regulation and the converter will sit in current limit through the rest of the ramp.
Thermal arithmetic in a 3 mm package
The HotRod body has the pads on the bottom and the thermal path is through the power pad into the plane. With a four layer board and the via pattern from the datasheet example, the junction to ambient figure is in the region of 30 to 35 degrees per watt, so 3 W of dissipation is 90 to 105 degrees of rise. In a 50 degree enclosure that is a junction at 140 to 155 degrees, which is over the limit, so the same 3 W needs a plane on both sides and either airflow or a lower ambient.
The practical rule for this body is that 2 W is a still air board with a good plane, 3 W needs airflow, and anything above that needs a different package or a two phase arrangement. That rule comes from the resistance figures and not from a marketing number, and it is worth applying before the loop is even tuned.
The missing A suffix
The datasheet in hand publishes only the A suffix rows. That does not prove the non A string is unavailable, and it does not prove the two are identical either. The correct handling is to ask the vendor for the orderable list against the exact string, and to treat a substitute between the two as a change that needs a functional check at the rail, the load and the temperature extremes.
Where a bill of materials has this string and the A row is what ships, the difference is usually a silicon revision with a fixed erratum rather than a different function, and the revision history section of the document is where that is confirmed. A buyer should never accept a substitution on the strength of a similar part number alone.
The power management cross reference page lists the pin compatible converters in this class, and the drop in replacement check is the procedure we run before a different suffix is approved on a board that already has a qualification file.
Questions that come with this string
Does the converter need an external compensation network? No, the control scheme is internally compensated and stable with ceramic output capacitors. That is the reason the part is popular on point of load rails where board area is the constraint.
What is the minimum output voltage? 0.6 V, which is the reference. A rail below that needs a different part or a resistor divider on the feedback pin of a converter that supports it.
How is the switching frequency chosen? By the mode pin, and the choice trades size against loss. A 1 MHz setting halves the inductor for the same ripple and adds roughly 25 percent to the switching loss, so a 5 V rail at 4 A is comfortable at 1 MHz and an 8 A rail is not.
What happens during an over current event? The part limits cycle by cycle, and if the fault persists the output voltage falls and the under voltage protection latches the output off. The latch is cleared by a re enable, which means a supervisor or a sequencer has to own the recovery, and the incoming inspection plan is where the reel level checks for a part with this much integrated protection begin.