Contact Us

TPS51206DSQR

Brand: Texas Instruments
Texas Instruments TPS51206DSQR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS51206DSQR — Power Management & Signal Chain | Superb Automation

TPS51206DSQR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS51206DSQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS51206 2 A sink and source DDR termination regulator in a 2 mm body

The TPS51206DSQR is a DDR termination regulator that both sinks and sources current, with a buffered VTTREF reference output, in a 10 pin 2 mm by 2 mm SON package. It produces the VTT rail that sits between the memory data pins, and it produces the VREF that the memory uses as its switching threshold. Both are needed on a DDR2, DDR3, DDR3L or DDR4 memory bus, and having them in one 2 mm part is what keeps the termination area small on a dense board.

The output is specified across 0.5 V to 0.9 V, which covers the DDR3L and DDR4 termination voltages, and the VTTREF output tracks the VDDQ sense input divided by two to within 1 %. The part draws its main supply from a 3.3 V or a 5 V rail and its LDO input from as low as VTT plus 0.4 V, so the termination current does not have to be dropped from the full 5 V rail.

Key parameters taken from the SLUSAH1E document

VDD supply3.1 V to 6.5 V recommended, so a 3.3 V or a 5 V rail both work with margin on both ends
VLDOINVTT plus 0.4 V up to 3.5 V, which is what lets a 1.2 V termination run from a 1.8 V or 2.5 V rail instead of from 5 V
VTT output0.5 V to 0.9 V, with plus or minus 20 mV of accuracy
Current2 A peak sink and 2 A peak source, which is the figure the termination of a 64 bit DDR4 channel needs during a write burst
Output capacitance10 microfarad of ceramic is enough for stability, and the data sheet prints that as the only output capacitor requirement
VTTREFVDDQ divided by two with 1 % accuracy, and 10 mA of sink and source drive for the memory reference pins
Power statesHigh impedance on VTT in S3, and soft stop of VTT and VTTREF in S4 and S5 through the S3 and S5 inputs
ThermalOvertemperature protection, 70.3 degrees per watt junction to ambient in the DSQ body, minus 40 to plus 105 degrees ambient
Remote senseA VTTSNS pin, so the regulator corrects for the drop in the trace between the part and the memory
ESD2000 V human body model

The remote sense pin and why it changes the placement

VTTSNS is a sense input, not a power pin. It measures the VTT voltage at the point where the termination resistors are, and the regulator corrects the output until that point is at the right level. Without it the part regulates at its own pin, and the copper between the pin and the termination resistors adds an error that grows with the termination current.

On a board with 30 termination resistors spread along a memory channel, the sense point is normally taken from the middle of the resistor row rather than from the end. Taking it from the end corrects one end and doubles the error at the other, and a 20 mV accuracy spec on the part buys nothing if the sense trace runs to the wrong place.

Where the TPS51206 belongs on the board

  • DDR3 and DDR3L memory on embedded computing boards where the termination has to fit under a heat spreader
  • DDR4 memory on networking and storage controllers, where the 0.6 V termination sits inside the 0.5 V to 0.9 V window
  • SSTL_18, SSTL_15, SSTL_135 and HSTL buses on telecom and datacom line cards
  • Set top boxes, printers and LCD televisions that carry a small DDR3 bank and want one part for both rails
  • Base station control boards where the termination rail has to be put into high impedance in a low power state

Order code, package and thermal limits

TPS51206DSQR10 pin WSON DSQ, 2.00 mm by 2.00 mm, large reel
Ambient rangeMinus 40 to plus 105 degrees, which is wider than the 85 degree parts that sit next to it on the same boards
Power dissipationAt 2 A and a 0.6 V termination from a 1.2 V LDO input, the part drops 1.2 W, and the 70.3 degrees per watt figure says that needs real copper under the pad
Capacitor on VTTREF0.22 microfarad to 1 microfarad for stability, so this is a separate capacitor from the VTT output bank
S3 and S5 inputsTwo logic inputs set the state, so the board can put VTT into high impedance without removing the VDD supply

Sourcing notes for this line

Termination regulators are small, cheap parts that stop a memory bus dead when they are missing, and the substitutes rarely match on both the LDO input range and the high impedance state behaviour. The comparison starting point is the memory cross reference, which lists the termination parts by memory generation and states which of them need a different output capacitor.

The pin to pin question matters here because the DSQ body is 2 mm square and a larger substitute will not fit the footprint. Where a drop in replacement is proposed, the sense pin arrangement and the S3 and S5 logic polarity are the two rows to check, and the how to verify a drop in replacement page sets out that check as a sequence.

Volume for these parts follows the memory generation, so a board built for DDR3L can be planned against DDR4 termination availability. The component lead time page covers what a mixed generation build looks like in scheduling terms.

Questions buyers ask about this part

Can it terminate DDR4 at 0.6 V? Yes. The 0.5 V to 0.9 V output window covers the 0.6 V DDR4 termination point, and the VTTREF output tracks VDDQ divided by two, so a 1.2 V DDR4 rail gives the right reference without a divider.

Is a 10 microfarad output capacitor really enough? For stability, yes, and the document prints that as the requirement. Whether it is enough for the transient depends on the distance to the termination resistors, which is why the remote sense pin exists.

What happens if S3 is asserted? VTT goes to high impedance and VTTREF stays alive, which is the state a memory in self refresh expects. In S4 or S5 both rails are discharged softly rather than switched off.

Does the part need a heatsink at 2 A? No, but it needs copper. At the worst case dropout the body dissipates more than a watt, and the 70.3 degrees per watt figure assumes a specific copper area under the pad that a two layer board may not have.