Contact Us

TPS40428RHAR

Brand: Texas Instruments
Texas Instruments TPS40428RHAR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS40428RHAR — Power Management & Signal Chain | Superb Automation

TPS40428RHAR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS40428RHAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS40428 dual output PMBus buck controller with an AVS bus and four phase stacking

The TPS40428RHAR is a driverless synchronous buck controller in the 40 pin 6 mm by 6 mm QFN body that runs two independent outputs, or two phases of one output, and stacks to four phases for a load as high as 120 A. It carries no integrated gate driver and no power switch, so it is paired with an external driver or with a smart power stage such as the CSD95378B, and it is pin for pin equivalent to the TPS40425 for boards that already use the non smart power mode.

The PMBus interface is the reason this part exists in a server bill of materials. Reference voltage, fault limits, UVLO threshold, soft start time, turn on delay and turn off delay are all programmable over the bus, and the part keeps the settings in on chip non volatile memory, so a factory default configuration boots without a host write. The AVS bus is separate from PMBus and runs at high speed, which is what a processor uses to move its own core voltage in small steps while it is running.

Key parameters taken from the SLUSBV0A document

Input supply4.5 V to 20 V single supply, which covers a 5 V or a 12 V intermediate bus without a separate bias rail
Output range0.6 V and up, set by the reference and the feedback divider
Reference accuracy0.6 V with 0.5 % from minus 40 to plus 125 degrees, which is the number that lets an ASIC core sit at a low voltage with margin
PhasesDual output, or 2, 3 or 4 phase interleaved, stackable to four phases for a load current up to 120 A
Switching frequencyProgrammable from 200 kHz to 1.5 MHz
PMBus featuresMargining up and down in 2 mV steps, programmable fault limit and fault response, current monitoring with 0.8 % VOUT accuracy
Temperature monitoring3 degrees of external temperature monitoring accuracy in smart power mode
Current sharingISH1 and ISH2 pins carry the sharing signal between phases, with the FB pin tied to BP5 to mark a channel as a slave
Bias railsBP3 at 3.3 V for logic with 0.33 microfarad minimum, BP5 bypass with 1 microfarad minimum, 10 microfarad maximum on either
Package and ESD40 pin 6 mm by 6 mm QFN with thermal pad, 2000 V human body model

How the four phase stack is wired

Multi phase operation is set by the PHSET pin and by the address resistors on ADDR0 and ADDR1, which give each device its PMBus address. A two phase stack shares one ISH line and one SYNC line, so the two devices switch at the same clock with a fixed phase offset. At three and four phases the interleaving spreads the input current pulses evenly across the switching period, which cuts both the input ripple and the output ripple, and that is the reason a 120 A rail can be built with a smaller number of input capacitors than four independent single phase converters would need.

The slave channel is configured by tying its feedback pin to the 5 V bias rail rather than to the output divider. That detail is easy to miss on a re-spin: a slave whose FB pin is still connected to a divider will try to regulate its own output and the sharing loop will fight it.

Where the TPS40428 belongs on the board

  • Server and storage boards that need a 0.9 V core rail at 100 A or more from a 12 V bus
  • Networking line cards where the ASIC core voltage has to be trimmed in 2 mV steps at run time
  • Test and measurement instruments that need the supply voltage logged over PMBus alongside the readings
  • Boards that already carry the TPS40425 footprint and want the smart power stage option without a re-spin
  • Telecom shelves with a 5 V intermediate bus, where the 4.5 V minimum input leaves margin for a bus dip

Order code, package and configuration storage

TPS40428RHAR40 pin RHA QFN, 6.00 mm by 6.00 mm, large reel, active and in production
Smart power modeFactory default, compatible with the CSD95378B stage, and the non smart power mode is reached by PMBus programming plus a power cycle
Non volatile memoryOn chip, stores a custom configuration so a board boots without a host write on every power up
Pin equivalencePin for pin equivalent to the TPS40425, which is the fallback when the smart power variant is not on the shelf
Prebiased outputSupported, so a rail that is already charged does not get pulled down at startup

Sourcing notes for this line

Multi phase controllers are the parts that hurt most during an allocation cycle, because a board that uses one cannot be reworked around a single phase substitute without changing the inductor count, the input capacitor bank and the sharing scheme. The comparison table to work from is the power management cross reference, which lists the PMBus controllers that share the 40 pin footprint and the ones that only look similar.

Where the TPS40428 is short, the TPS40425 is the first candidate because it is pin for pin equivalent and differs in the smart power stage support rather than in the package. Whether a board can move between them depends on whether the power stage is a CSD95378B, which is the check on the pin to pin cross reference page.

Long lead time on the controller usually comes with a shorter lead time on the power stage and the reverse, so a build that is missing both needs the two lines planned together. The one stop BOM sourcing page describes how a multi phase rail is kitted as one group rather than as separate line items.

Questions buyers ask about this part

Does it need an external driver? Yes. There is no gate driver inside, so each phase needs a driver or a smart power stage. That is the difference between this part and a converter with integrated FETs, and it is what allows the 120 A figure at four phases.

Can the settings survive a power cycle? Yes. The configuration is held in on chip non volatile memory, so a board that has been programmed once boots with that configuration. A blank part boots in smart power mode with factory defaults.

What is the AVS bus for? It lets the load move its own supply voltage in small steps without a PMBus transaction, which is how a processor trades voltage for frequency while it runs. The PMBus still sets the limits and reads the telemetry.

How accurate is the current reading? The document prints 0.8 % VOUT accuracy for the monitoring path, and the current sense uses the CS pins across an external sense element, so the accuracy at the board level depends on that element and not only on the controller.