TPS40305DRCR
Product Specifications
TPS40305DRCR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS40305DRCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS40305 1.2 MHz synchronous buck controller for a 3 V to 20 V input rail
The TPS40305DRCR is a voltage mode synchronous buck controller in the 10 pin 3 mm by 3 mm VSON body with the thermal pad tied to ground. It drives an external high side and low side MOSFET pair from a rail anywhere between 3 V and 20 V, and it runs at a fixed 1.2 MHz, which is the highest of the three members of the TPS4030x family. The controller itself carries no power switch, so the current a board can deliver is set by the FETs and the inductor, not by the part number.
Three features decide whether this member is the right choice. The first is voltage mode control with input voltage feed forward, which reacts to a step on the input without waiting for the loop to notice it, so a 12 V rail that sags when a disk spins up does not push the output out of window. The second is the frequency spread spectrum block, which dithers the 1.2 MHz clock and spreads the switching harmonics, so a 1.2 MHz clock that would otherwise sit on a narrow peak in the conducted emissions scan becomes a wider and lower hump. The third is prebiased output support, which matters when a 1.2 V FPGA rail is already charged by its own internal path before the controller starts.
Key parameters taken from the SLUS964D document
| Input range | 3 V to 20 V on VDD, 22 V absolute maximum, so a 20 V rail sits exactly at the recommended limit and not above it |
| Switching frequency | 1.2 MHz on the TPS40305, fixed by the part number, against 300 kHz on the TPS40303 and 600 kHz on the TPS40304 |
| Reference | 600 mV with 1 % at room, and 594 mV to 606 mV over the full minus 40 to plus 125 degree junction range |
| Minimum pulse width | 70 ns, which is the row that sets the maximum practical step down ratio at 1.2 MHz, roughly 12 to 1 before pulse skipping starts |
| Shutdown current | 70 microamp typical and 100 microamp maximum with EN/SS held below 0.2 V |
| Quiescent current | 2.5 mA typical and 3.5 mA maximum while not switching, with EN/SS floating |
| Bias regulator | 6.5 V at 10 mA, with 70 mV typical dropout when VDD is at 3 V, which is what allows a 3.3 V input to drive the high side FET |
| Soft start | 10 microamp sourced into the EN/SS capacitor, with an 0.8 V reference level, so 10 nF gives roughly 0.8 ms of ramp |
| Thermal shutdown | 145 degrees, with a 10 pin VSON whose junction to ambient figure is 44.3 degrees per watt |
| ESD | 2000 V human body model and 1500 V charged device model |
Setting the current limit without a sense resistor
Overcurrent is measured across the on resistance of the low side FET, so there is no shunt in the power path and no extra milliohms in series with the inductor. The level is programmed by one resistor from the LDRV pin to ground. At power on the controller runs a calibration cycle, measures the voltage at that pin and stores the level internally. During operation it compares the drop across the low side FET while that FET is on against the stored level, and on a trip it shuts down and restarts until the fault clears.
The RDS(on) sensing scheme drifts with temperature, which is why the OCP level is thermally compensated in the part. The practical consequence for a buyer is that the same resistor gives a wider current limit window on a hot board than on a cold one, and a board that trips at 8 A on the bench may trip earlier in a sealed enclosure. The compensation is there to make the window predictable, not to remove it, and a board that runs the FET within 20 % of the limit needs the worst case RDS(on) at 125 degrees rather than the 25 degree number.
Where the TPS40305 belongs on the board
The applications the vendor lists are point of load modules, printers, digital TVs, telecom equipment and USB Type-C wall receptacles. The common thread is a 5 V to 20 V intermediate bus that has to produce one or two low voltage rails on a board where the height budget rules out a module.
- Point of load converters on a 12 V backplane, where 1.2 MHz keeps the inductor small enough to fit under a shield can
- Telecom line cards and small cells that need a 1.0 V or 1.2 V core rail from a 12 V feed
- Printers and multi function machines, where the 1.2 MHz clock sits above the audible band and away from the motor drive
- USB Type-C wall adapters with a 20 V PD rail, where the input window of the part matches the top of the PD range
- Set top boxes and display boards that need prebiased startup so the load is not discharged on power up
Order code, package and thermal budget
| TPS40305DRCR | 1.2 MHz member, 10 pin VSON DRC, 3.00 mm by 3.00 mm, large reel |
| TPS40305DRCT | Same silicon on the small reel, for prototype quantities |
| Siblings | TPS40303DRCR at 300 kHz and TPS40304DRCR at 600 kHz, same body and same pinout, different fixed clock |
| Junction range | Minus 40 to plus 125 degrees recommended, 150 degrees storage |
| Thermal pad | The pad is the ground connection, so the number of vias under the body decides the junction temperature more than the copper area around it |
| Gate drive | HDRV and LDRV swing from the 6.5 V bias rail, which suits logic level FETs and not standard threshold parts |
Sourcing notes for this line
A 1.2 MHz controller in a 3 mm body is a part that moves in and out of allocation with the analog capacity cycle, and the substitutes on the market are rarely equal on both the minimum pulse width and the prebiased start behaviour. The useful comparison is against the power management cross reference, which lists the controllers that share the pinout and marks the ones whose minimum on time is longer.
When the exact order code is short, the first lever is the 600 kHz member of the same family, because it shares the body and the pinout and only changes the inductor and the compensation. That swap is covered on the pin to pin cross reference page, and it needs the inductor value and the output capacitor checked before a line is released, since a 600 kHz board needs roughly twice the inductance for the same ripple.
For repeat programmes the reel and the moisture level decide whether a part can go straight to the line. Where the large reel is not available and a re-reel is offered instead, the component lead time page sets out what each option costs in scheduling terms.
Questions buyers ask about this part
Can it run from a 24 V rail? Not directly. The recommended input stops at 20 V and the absolute maximum is 22 V, so a 24 V bus needs a front end clamp or a different controller. The 145 degree thermal shutdown does not protect the part against an overvoltage event on VDD.
Why pick 1.2 MHz over 300 kHz? Board area. At 1.2 MHz the inductor and the output capacitor are roughly a quarter of the size they need to be at 300 kHz for the same ripple, at the cost of about 1 % to 2 % of efficiency from switching loss and a tighter limit on the step down ratio because of the 70 ns minimum pulse.
Is the output safe with no load? Yes. The controller is a voltage mode part with a fixed clock, so it does not enter a burst mode at light load and the output stays regulated, which is what a board with a hot plug connector needs.
What sets the switching node ringing? The high side FET turn on and the loop inductance between the FET, the input capacitor and the pad. The 3 mm body with the ground pad gives a short return, but the input capacitor placement is the term that decides the peak voltage on SW.