Contact Us

TPS40190DRCR

Brand: Texas Instruments
Texas Instruments TPS40190DRCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS40190DRCR — Power Management & Signal Chain | Superb Automation

TPS40190DRCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS40190DRCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS40190DRCR: synchronous buck controller from 4.5 V to 15 V with a fixed 300 kHz frequency

TPS40190DRCR is a small voltage mode controller that drives external MOSFETs at a fixed 300 kHz, with a 0.591 V reference and a 1.2 A gate driver in a SON body of 10 pins. The TPS40190 is a cost optimised synchronous buck controller for a 4.5 V to 15 V input. It uses voltage mode control at a fixed 300 kHz, holds a 0.591 V reference with one percent accuracy, and includes a 5 V regulator for its own housekeeping and light external loads. The gate drivers source and sink 1.2 A for the high-side and the low-side N-channel devices, with a bootstrap diode inside the package. Soft start is internal, the overcurrent threshold is selectable, and the body is a 3 mm by 3 mm 10 pin SON.

Order code and package

Order codeTPS40190DRCR
Input voltage4.5 V to 15 V
Reference0.591 V, one percent accuracy
Controlvoltage mode, fixed frequency
Switching frequency300 kHz fixed
Gate drive1.2 A source and sink for both switches
Housekeeping regulatorinternal 5 V
Soft startinternal
Package10 pin SON, 3 mm by 3 mm
Overcurrentselectable short circuit protection thresholds
Pre-biassafe start into an output that is already held up
DocumentSLUS658D, July 2005, revised June 2019

Electrical parameters that decide the application

Turn-on voltage4.1 V minimum, 4.25 V typical, 4.4 V maximum
UVLO hysteresis270 mV to 370 mV
High-side driver pull-up3 Ohm minimum, 6 Ohm maximum at 4.5 V
High-side driver pull-down1.5 Ohm minimum, 3 Ohm maximum
Low-side driver pull-up2.5 Ohm minimum, 5 Ohm maximum
Low-side driver pull-down0.8 Ohm minimum, 1.5 Ohm maximum
Enable thresholds2.8 V high minimum, 0.6 V low maximum
Bootstrap diode drop0.6 V to 1.2 V at 5 mA
Anti-cross conductionadaptive, with a dead time between the drivers
Junction range-40 C to 85 C ambient
Thermal paththe die pad of the 3 mm by 3 mm body
Output voltageset by an external divider from the 0.591 V reference

Points to check before this part goes on a BOM

A 0.591 V reference is an unusual number and it is worth respecting. A divider built for a 0.6 V reference produces an output about 1.5 percent high, which at 1.2 V is 18 mV, and that is more than the reference tolerance. Boards moving between controller families should recalculate the divider rather than reuse the resistors from the previous board.

Voltage mode control needs the compensation network to match the output filter, and at a fixed 300 kHz the poles are fixed with it. The advantage is predictability: the same network works for the same inductor and capacitor combination across builds. The disadvantage is that a change of output capacitance, which is the most common cost reduction in a programme, moves the resonance and can leave the loop with less margin than the original validation covered.

The 1.2 A gate drive is modest by controller standards, so the choice of MOSFET is part of the loop. A large die with a high gate charge will slow the switching transitions and raise the loss in the FET, while a small die keeps the transitions fast but has a higher on resistance. At 300 kHz and a 12 V input the balance usually lands on a device with a gate charge of 20 nC to 40 nC.

Fixed 300 kHz cannot be synchronised to another clock. On a board with several converters this is a limitation, because the beat between 300 kHz and a neighbouring 500 kHz supply lands at 200 kHz and its harmonics, which is inside the band where an input filter is least effective. The practical answer is to keep the input capacitors separate and the return paths short.

Pre-bias safe start matters in a system with several rails. If the output is held at a voltage by another supply when the controller is enabled, the part does not pull it down before ramping, so a device with two supply pins never sees a reverse bias. The behaviour depends on the driver timing and it should be confirmed on the bench rather than assumed from the feature list.

The internal 5 V regulator is available for light external loads, which can save a small bias supply on a board. The limit is a few milliamps, and a load beyond it pulls the regulator down, which degrades the gate drive and shows up as additional switching loss rather than as an obvious failure. Boards that use this rail for an op amp should check the current budget first.

A 3 mm by 3 mm SON with ten pins has little copper under it, so the thermal path is through the board rather than the package. The controller dissipates only the gate drive and its own housekeeping, which is a few hundred milliwatts at 300 kHz, so the package is not the constraint; the external FETs are, and they need the copper.

Where this order code fits

This order code fits cable modem customer premises equipment, digital set top boxes, access points and embedded boards that need 5 A to 15 A at 1 V to 3.3 V from a 12 V rail, where the cost of an integrated converter with the same current is not justified. The fixed 300 kHz frequency also suits boards that want the input filter settled once. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the How to Reduce Component Cost page.

Questions buyers ask

Can the frequency be changed? No. It is fixed at 300 kHz, which is why the input filter can be settled once for a product family.

Does it include the MOSFETs? No. It drives external N-channel devices through a bootstrap high-side driver and a low-side driver.

What are the input voltage limits? 4.5 V to 15 V operating, with a 4.25 V turn-on threshold and about 320 mV of hysteresis.

SUPERB supplies this order code with date codes and packing stated, and the BOM Shortage Recovery page sets out the cost and availability checks for a controller in a long lived product.