Contact Us

TPS3896PDRYR

Brand: Texas Instruments
Texas Instruments TPS3896PDRYR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS3896PDRYR — Power Management & Signal Chain | Superb Automation

TPS3896PDRYR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS3896PDRYR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS3896PDRYR adjustable voltage monitor with a push-pull active-low output

The TPS3896PDRYR is a single channel voltage monitor in the 6 pin USON body of 1.45 mm by 1.00 mm. The sense input is separate from the supply and compares against an internal reference, so a resistor divider sets the trip point anywhere above 500 mV, and the output is a push-pull active-low line that needs no pull-up.

The P suffix is the variant with a capacitor adjustable delay on both the sense input and the enable input, which is the difference from the A suffix. On the A part the enable path is a fixed 0.2 microsecond pass through, and on the P part both edges are set by the same CT capacitor. That matters on a board where the enable signal comes from a mechanical switch or a slow comparator, because a 0.2 microsecond path passes contact bounce straight to the output.

Key parameters taken from the SBVS172B document

Supply range1.7 V to 6.5 V on VCC, with the monitored node on a separate sense pin
ThresholdAdjustable down to 500 mV through an external divider, with 0.25 % typical and 1 % maximum accuracy over temperature
Supply current6 microamp typical, which is the figure that decides whether the part can run from a battery rail
OutputPush-pull active-low, so the line drives a gate or an enable pin without a resistor
Enable inputActive low on this variant, so pulling the pin high releases the output immediately
Delay, sense path40 microseconds with CT open, and the delay follows 4 microseconds per nanofarad above that
Delay, enable pathCapacitor adjustable on the P member, which is the whole difference from the A member
CT pinCharged and discharged internally, so the delay is set by capacitance alone and no timing resistor is needed
Power-on resetOutput defined down to 1.65 V of VCC, with an undervoltage lockout that deasserts the output below it
Input currentNanamp level on the sense pin, which is what allows a high value divider without loading the node
BodyUSON 6 pin, 1.45 mm by 1.00 mm, the smallest footprint in this part of the catalogue
CompatibilityPin for pin compatible with the MAX6895, MAX6896, MAX6897 and MAX6898 monitors

What an adjustable threshold buys on a small board

A fixed threshold part forces the trip point to be a catalogue value, and on a rail that is not one of those values the only options are a wrong threshold or a divider in front of a fixed part, which stacks two tolerances. An adjustable part puts one divider in front of a 1 % reference and leaves the arithmetic to the customer.

The divider arithmetic is the part that usually gets skipped. With a 0.25 % typical reference and 1 % resistors the trip point moves by roughly 2.3 % across a production run, and the sense pin current of a few nanoamps sets how high the divider can be before that current becomes a term. A 100 kOhm top resistor is safe, a 1 MOhm top resistor is not, and the difference is a few microamps of standing current on a battery rail.

The separate supply pin is the second advantage, and it is the one that gets used least. A monitor running from a 3.3 V housekeeping rail can watch a 1.2 V core that has already collapsed, because the part that reports the fault is not the part that lost its supply. With a single pin device that arrangement is impossible.

Delay, enable and the difference between the A and P members

The CT pin is a capacitor and nothing else, and the vendor gives the relationship directly: the rising delay is 4 microseconds per nanofarad plus 40 microseconds. That is a shortcut that avoids a curve and it holds across the range the document characterises.

CT open40 microseconds, the fastest release and the setting used where only a defined edge is needed
1 nFAbout 44 microseconds by the printed relationship
10 nFAbout 80 microseconds, a setting that covers connector bounce on a switch input
100 nFAbout 440 microseconds, used where a relay or a lamp driver has to settle first
0.047 microfarad190 ms, the point the timing table prints, and the largest value the document works through
Enable path0.2 microsecond on the A member, capacitor adjustable on the P member, and that is the only behavioural difference between them

The enable pin is active low on this variant, so the logic reads backwards compared with a conventional enable. Pulling it high releases the output after the delay, and pulling it low forces the output low immediately, whatever the sense pin is doing. On a board that already uses an active high enable, the TPS3895 is the mirror image and the wiring is not interchangeable.

Where the TPS3896P is used

  • DSP, microcontroller and FPGA boards where the core rail has no catalogue threshold
  • Notebook and desktop boards that monitor a divided rail rather than a fixed one
  • Handheld and battery products where 6 microamp of standing current is affordable but 50 is not
  • Boards that replace a MAX6895 class monitor without changing the footprint
  • Any node where the enable comes from a switch and the bounce has to be filtered by the same capacitor as the release delay

The footprint is the reason the part appears in enquiries from customers who are re-spinning a board that already has a USON land pattern. At 1.45 mm by 1.00 mm there is no room for a second timing component, and the CT capacitor is the only external part besides the divider.

Order code, marking and reel

TPS3896PDRYRUSON DRY 6 pin, 3000 pieces on a large reel for the small body
VariantsTPS3895A and P are the active-high equivalents, TPS3897 and TPS3898 are the open-drain members rated at 18 V
Threshold setEvery variant is adjustable, so the trip point lives in the divider and not in the order code
DocumentSBVS172B, revised April 2015, which is the only document for the family and covers all eight variants

Because the trip point is set by the customer's divider, the same order code serves several rails on one board. That is convenient for a stock position and awkward for traceability, because a reel of TPS3896PDRYR can be used on a 1.2 V rail and on a 3.3 V rail in the same build.

Sourcing notes for this line

An adjustable monitor in a 1.45 mm by 1.00 mm body is a footprint driven purchase, and the substitutes that fit the land pattern rarely match on the enable polarity. The power management cross reference lists the pin compatible parts and states the enable polarity of each, which is the field that stops a wrong part reaching the line.

The family is also a candidate for an obsolescence event, because the parts it was brought in to replace are still in catalogues and customers keep both on a drawing. The pin to pin cross reference page sets out the pairs that are interchangeable in the land pattern and the ones that only look alike.

For a build that needs the part before the lead time clears, the A variant with the fixed enable path is the same silicon and the same reel size, and it is often in stock when the P variant is not. The difference shows up only where the enable input bounces. The component lead time page covers that substitution and what has to be re-checked.

Questions buyers ask about this part

Is the output really push-pull? Yes on the 3895 and 3896. The open-drain members are the 3897 and 3898, and they are the ones to specify for a wired-or reset bus.

What is the lowest rail it can watch? 500 mV by the feature list, and the divider has to sit above that with the reference tolerance accounted for.

Does the part work with the sense pin tied to the supply? It does, and that is the arrangement used when the divider is not wanted. The trip point is then the reference divided by the divider ratio of one, which is 505 mV.

Can the enable pin stay unconnected? No. It is an input with a defined function and it has to be tied to a level, high to enable and low to hold the output down.