Contact Us

TPS389001QDSERQ1

Brand: Texas Instruments
Texas Instruments TPS389001QDSERQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS389001QDSERQ1 — Power Management & Signal Chain | Superb Automation

TPS389001QDSERQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS389001QDSERQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS389001QDSERQ1 adjustable automotive supervisor with a 1% threshold

The TPS389001QDSERQ1 is the adjustable member of the TPS3890-Q1 family, a low current supervisor in the 6 pin WSON body of 1.50 mm by 1.50 mm. Because the sense input is separate from the supply, a resistor divider sets the trip point anywhere down to 1.15 V, which is what makes the part usable on rails that have no catalogue threshold, such as a 2.5 V reference or a 1.2 V core.

The 01 in the order code is the field that says adjustable. The fixed members of the same family carry the rail voltage instead, 18 for 1.8 V and 33 for 3.3 V, and the two are otherwise identical in body, pinout and delay behaviour. That is the detail to check on a purchase order, because an adjustable part on a fixed-rail board leaves the divider as the only thing setting the trip.

Key parameters taken from the SBVS303B document

QualificationAEC-Q100 grade 1, minus 40 to plus 125 degrees junction, HBM level 2 and CDM level C4B
Supply range1.5 V to 5.5 V on VDD, and the sense pin is separate from the supply pin
Adjustable thresholdThe TPS389001-Q1 monitors any rail down to 1.15 V through an external divider, with 1.157 V as the printed reference point
Threshold accuracy0.5 % typical and 1 % maximum over the full temperature range
Hysteresis0.575 % typical, printed as a 0.325 to 0.825 % window of the trip point
Supply current2.09 microamp typical and 3.72 microamp maximum at 3.3 V from minus 40 to 85 degrees, rising to 4.5 microamp up to 105 degrees
Sense input current10 nA typical and 100 nA maximum, which is what keeps a high value divider usable
Reset delay25 microseconds with no capacitor up to 30 s at 26 microfarad on the CT pin
CT pin1.15 microamp charging current and a 1.23 V comparator threshold, so the delay is set by capacitance and not by a resistor
Propagation18 microseconds falling and 25 microseconds rising at a 3.3 V supply with CT open
Manual resetMR pin, 250 ns from a low on MR to the output
OutputOpen-drain active-low RESET, 250 nA leakage at 5.5 V and 0.25 V maximum low at 3 mA
Power-on resetOutput defined from 0.8 V of VDD

Setting the trip point with a divider

The threshold is set by the ratio of two resistors, so the accuracy of the trip is the accuracy of the reference plus the accuracy of the resistors. With a 1 % reference and 1 % resistors the worst case trip moves by about 2.4 %, and with 0.1 % resistors the reference dominates. The 10 nA typical sense current is the term that decides how high the divider can go, because that current flows through the top resistor and adds to the drop.

A 100 kOhm top resistor with 10 nA of input current drops 1 mV, which is negligible against a 1 V threshold. A 1 MOhm top resistor drops 10 mV, which is 1 % of the trip point and half of the reference budget. That is the calculation to put in front of a customer who wants a microamp level divider on a battery product.

The supply and the sense pin are separate on this part, which allows the supervisor to run from a 3.3 V housekeeping rail while it watches a 1.2 V core that has already collapsed. On a single pin part that arrangement is impossible, because the supervisor dies at the same moment as the rail it is watching.

Programming the delay from microseconds to half a minute

The CT pin is charged by an internal 1.15 microamp current source and the output is released when the pin reaches 1.23 V, which gives a delay that is close to linear in capacitance.

CT open25 microseconds, used when the reset only has to be seen by a gate
1.5 nFAbout 1 ms, and the vendor works the example in the document to show that 1.149 nF is the calculated minimum for 1 ms across temperature
100 nFAround 100 ms by the same scaling, a common figure for a core rail with a slow reference
1 microfaradAround 1 s, the setting for a module that has to hold a converter off while it discharges
26 microfarad30 s, the top of the range and the point at which capacitor leakage becomes part of the delay

Because the current source is small, leakage on the CT pin matters more here than on a supervisor with a microamp level charge current. A 1 microfarad ceramic with a few nanoamps of leakage shifts a one second delay by milliseconds, and a wet tantalum with microamps of leakage shifts it by seconds. The vendor asks for a low leakage capacitor and a short trace for that reason.

Where the adjustable member is used

  • Core rails at 1.2 V, 1.0 V and below, where no catalogue threshold exists
  • Automotive camera and sensor modules with a 1.8 V or 1.2 V rail that has to be watched separately from the 3.3 V housekeeping rail
  • Boards where the trip point has to be trimmed at the test station rather than fixed at purchase
  • Modules that monitor a divided battery voltage as well as a logic rail, using two dividers and one part
  • Instruments that need a delay in the hundreds of milliseconds without a second timing component

The adjustable version also covers a case the fixed members cannot: a rail whose nominal voltage is decided late in the programme. A divider change on a prototype board is a two resistor rework, while a threshold change on a fixed part is a new order code and a new safety stock position.

Order code, marking and reel

TPS389001QDSERQ1Active, production, WSON DSE 6 pin, 3000 pieces on a large reel, marking 2N
Lead finishNIPDAUAG, moisture level 1 at 260 degrees with unlimited floor life
Body size1.50 mm by 1.50 mm, the same as the fixed members of the family
Fixed alternativesTPS389018-Q1 watches a 1.8 V rail with a 1.73 V negative threshold, and TPS389033-Q1 watches 3.3 V, both on the same body

The marking is two characters, so the body does not tell an adjustable part from a fixed one. That distinction lives on the reel label and in the order code, and a store that mixes the two will find out at first article.

Sourcing notes for this line

The adjustable version is usually specified late, which means it is usually short when the build starts. Because the family shares a body and a pinout, the practical bridge is a fixed member on the same reel size while the divider is reworked, and the power management cross reference lists which fixed thresholds are pin compatible.

Where a customer needs a threshold below 1.15 V, no member of this family reaches it and the honest answer is a different part rather than a divider trick, because the reference itself sets the floor. The pin to pin cross reference page lists the alternatives that go lower and states the package change each one brings.

These parts also sit on long life automotive boards where the lifecycle notice arrives years before the last build. The component obsolescence management page covers how a buffer is held and how a last time buy is sized against the remaining forecast.

Questions buyers ask about this part

Can it watch a negative rail? Not with this part. The sense input is referenced to ground and the supply has to be positive.

Does the divider need a bypass capacitor? Yes in most cases, because a high value divider with a 10 nA input current picks up noise, and a 10 nF capacitor at the sense pin is the usual fix.

How accurate is the trip point in practice? The reference contributes 1 % and the resistors contribute their own tolerance, so a 1 % resistor pair gives roughly 2.4 % worst case and a 0.1 % pair gives about 1.2 %.

Can the MR pin be left floating? No. It has to be tied to VDD when it is not used, and the data sheet says so in the application section.