TPS3851G30EDRBR
Product Specifications
TPS3851G30EDRBR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS3851G30EDRBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS3851G30EDRBR supervisor with a 2.88 V threshold and an integrated watchdog
The TPS3851G30EDRBR is a precision supply supervisor with a watchdog timer in one 8 pin VSON body of 3.00 mm by 3.00 mm. The G30 field sets the two numbers that matter: G means the threshold sits 4 % below the rail it watches, and 30 means the rail is 3.0 V, so the falling threshold is 2.88 V. The E field sets the watchdog timing, and the trailing R is the large reel.
Two things separate this part from a plain supervisor. The threshold accuracy is 0.8 % across the full minus 40 to plus 125 degree range, which is tight enough to watch a 3.3 V rail without a divider and still leave a usable margin. And the watchdog has its own output, WDO, so the controller can tell an undervoltage event from a code hang without a second pin or a second part.
Key parameters taken from the SBVS300B document
| Supply range | 1.6 V to 6.5 V on VDD, which covers a 3.3 V rail with room for the supply tolerance |
| Falling threshold | 2.88 V, which is 4 % below the 3.0 V nominal, held to plus or minus 0.8 % over temperature |
| Hysteresis | 0.5 % typical, printed as a 0.2 to 0.8 % window, so the release point is roughly 2.90 V |
| Supply current | 10 microamp typical and 19 microamp maximum, a figure that includes the watchdog |
| Reset delay | 200 ms nominal, 170 to 230 ms, fixed in the part rather than set by a capacitor |
| Watchdog, factory setting | 1600 ms with the CWD pin open and SET1 high, printed as 1360 to 1840 ms |
| Watchdog, capacitor setting | 200 ms with a 10 kOhm resistor from CWD to VDD and SET1 high |
| Watchdog, disabled | SET1 pulled low turns the watchdog off, which is the state used during board bring-up |
| CWD pin | 375 nA charging current, 347 to 403 nA, and a 1.21 V comparator threshold |
| Watchdog reaction | WDO asserts only while RESET is high, so a supply fault and a code hang never appear on the same pin |
| Manual reset | MR pin with a 620 nA internal pull-up current, so a switch to ground is a complete circuit |
| Undervoltage lockout | 1.35 V, below which RESET is driven low regardless of the threshold comparison |
| Power-on reset | Output defined from 0.8 V of VDD |
| Body | VSON 8 pin, 3.00 mm by 3.00 mm nominal |
What the G30 field decides
The threshold is not a fixed catalogue number on this family. It is a percentage below a nominal rail, and the two fields are read together: G is the 4 % option, H is the 7 % option, and the two digit field names the rail from 1.8 V through 5.0 V. A G30 part therefore trips at 2.88 V and an H30 part at 2.79 V, on the same silicon and the same reel.
That matters at the quotation stage, because a customer who asks for a 3.0 V supervisor without naming the tolerance will get one of the two and the difference is 90 mV. On a 3.3 V rail at minus 5 %, 3.135 V, both parts hold the rail up long enough. On a 3.0 V rail the H option at 2.79 V is the one that does not trip during a normal load step, and the G option at 2.88 V is the one that does.
The 0.8 % accuracy is the other half of the argument. A 1.5 % or 2 % part forces the customer to add margin on both sides, and on a 3.0 V rail that margin is the whole difference between a supervisor that protects the flash and one that resets on every motor start.
Setting the watchdog window
The watchdog timeout is either taken from the factory setting or set by a capacitor on CWD, and the timing equation depends on the third letter of the order code. On the E variant the equation is 77.4 milliseconds per nanofarad plus 55.2 milliseconds, which is the long window intended for a software task that runs every second or so.
| CWD open, SET1 high | 1600 ms nominal, the factory default and the setting used when nothing is decided yet |
| CWD 10 kOhm to VDD | 200 ms nominal, the short window used when the software loop closes every few tens of milliseconds |
| SET1 low | Watchdog disabled, which is the state for a board that has no code to kick it yet |
| E timing equation | 77.4 ms per nF plus 55.2 ms, so 1 nF gives about 133 ms and 10 nF about 829 ms |
| S timing equation | The other factory option, 3.23 ms per nF plus 0.381 ms, which is the short window family |
| WDI pin | 50 ns minimum pulse and 50 ns from the WDI edge to WDO, so the pin can be driven from a GPIO |
| Enable setup | 150 microseconds after the watchdog is enabled before the part responds to WDI changes |
Two timing details catch people out. The WDO output only asserts while RESET is high, so a watchdog fault is invisible during the reset window by the arrangement of the part and not by fault. And the CWD pin is a current source charging a capacitor, so board leakage on that pin adds to the timeout, which is why the vendor recommends keeping the trace short and the flux clean.
Where the TPS3851 fits
- WLAN access points and IP cameras, where the processor has to be recovered from a hang without a power cycle
- Wireless security cameras and battery backed sensors with a 3.0 V or 3.3 V rail
- String inverters and electricity meters that need the watchdog inside the safety path
- Blood pressure monitors and other medical instruments where the reset source has to be identifiable
- Any board where the undervoltage event and the software hang must be logged separately
The separate WDO pin is the reason the part turns up in instruments rather than in plain power supplies. A single reset line tells the controller that something went wrong. Two lines tell it whether the supply sagged or the code stopped, and that difference decides whether the next boot runs a self test or just restarts the task.
Order code, marking and reel
| TPS3851G30EDRBR | Active, production, SON DRB 8 pin, 3000 pieces on a large reel |
| Lead finish | NIPDAU with a tin option on the same row, moisture level 1 at 260 degrees with unlimited floor life |
| Part marking | 851FD, and the H30 automotive equivalent marks 851NF, so the two are distinguishable on the reel |
| Small quantity | TPS3851G30EDRBT is the 250 piece small reel under the same threshold and timing |
| Automotive | TPS3851G30EQDRBRQ1 is the AEC-Q100 grade 1 equivalent on the same die |
Note that the .A row of the same code carries a different quantity on some lines, so a purchase order should name the reel size and not only the orderable string.
Sourcing notes for this line
A supervisor with an integrated watchdog is a narrow substitution. Parts that match the footprint often differ in whether the watchdog output is separate, in the factory timing option and in the hysteresis, and any one of those changes the behaviour of the reset chain. The power management cross reference lists the candidates and marks the ones where the watchdog is shared with the reset pin.
Where the exact code is on a long lead time, the two field levers are the 7 % threshold option and the S timing option, both of which are published rows rather than specials. Neither is a drop in without a check, because the threshold moves 90 mV and the watchdog window changes by a decade. The pin to pin cross reference page sets out what has to be re-checked on the first article.
These parts also sit in equipment with a ten year service life, where the vendor lifecycle status is as important as the stock position. The component obsolescence management page covers how a buffer is held against a status change on parts of this class.
Questions buyers ask about this part
Does the watchdog need an external capacitor? No. The factory setting works with CWD open, and a capacitor or a resistor to VDD only shifts the window.
Can the watchdog be turned off in the application code? Yes, through SET1, and that is the intended use during bring-up. Leaving it off in production removes the whole reason the part was chosen.
Is the 200 ms reset delay adjustable? No. It is fixed at 170 to 230 ms, and a longer hold has to come from the controller or from a second part.
How is a watchdog fault cleared? By a valid WDI edge, and the WDO line returns high on its own once the sequence resumes. It does not latch.