Contact Us

TPS3839G12DBZR

Brand: Texas Instruments
Texas Instruments TPS3839G12DBZR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS3839G12DBZR — Power Management & Signal Chain | Superb Automation

TPS3839G12DBZR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS3839G12DBZR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS3839G12DBZR 150 nA supervisor for a 1.1 V threshold

The TPS3839G12DBZR is the 1.1 V member of the same nano power family as the 0.9 V option, in the same 3 pin SOT-23 body with the same 150 nA typical supply current. It watches a single rail and pulls its push pull output low while the rail is below the threshold, releasing it 200 milliseconds after the rail has recovered. The threshold is printed as 1.073 V minimum, 1.1 V typical and 1.117 V maximum, which is a plus or minus 1.2 per cent window.

The difference from the 0.9 V option is smaller than the label suggests and larger than the tolerance: 200 mV of threshold and a hysteresis of 11 mV instead of 54 mV. A board that monitors a 1.2 V rail wants this member, and a board that monitors a single cell at the end of its discharge wants the other one.

Key parameters taken from the TPS383x document

Threshold1.1 V nominal, printed as 1.073 V minimum and 1.117 V maximum at 25 degrees
Rail it suitsA 1.2 V rail at minus 5 per cent is 1.14 V, which sits above the 1.117 V maximum threshold
Hysteresis11 mV on this option, against 54 mV on the 0.9 V option and 29 mV on the 2.93 V option
Supply range0.9 V to 6.5 V operating, with a defined output down to a 0.6 V supply
Supply current150 nA typical
Reset delay200 milliseconds typical after the rail rises above the threshold plus the hysteresis
OutputPush pull active low, 120 microamp of sink at 0.9 to 1.2 V and 2 mA at 2.8 to 6.5 V
Manual resetNot fitted on this member
Transient behaviourMade to ignore fast transients on the supply pin, per the family description
Body3 pin SOT-23 DBZ
Reel and marking3000 pieces on a large reel, body marking PZBI, moisture level 1 at 260 degrees with unlimited floor life
TemperatureMinus 40 to plus 85 degrees C

The 11 mV of hysteresis on a 1.1 V threshold is 1 per cent of the trip point, which is tight. On a rail that is regulated and quiet, that is exactly what is wanted, because the supervisor then reports the rail rather than its own smoothing. On a rail that carries a switching converter with burst mode ripple of 20 mV, the same 11 mV means the output can follow the ripple and chatter. The vendor publishes a family curve of threshold against temperature and the hysteresis selections differ per option for this reason, so the choice of option is partly a choice of how much noise the supervisor should ignore.

Where the numbers matter in a real build

A 1.2 V rail is usually a core rail or a low voltage logic rail, and the 1.1 V threshold sits about 8 per cent below nominal. That is below the tolerance of the regulator, so the supervisor asserts only once the rail has actually failed and not while it is inside its own window. The consequence is that a processor on that rail keeps running until it is very close to the level where its own core stops, which leaves little time for a shutdown routine. Where more warning is needed, the answer is a second supervisor on the input rail rather than a higher threshold here.

The 200 millisecond delay after recovery is the number that decides how the board starts. A regulator that settles in 5 milliseconds still waits 200 milliseconds before the processor is released, which on a battery product that wakes every second is 20 per cent of the duty cycle. On mains powered equipment the same delay is invisible, and the part is cheap enough that it is often left in place on boards where the delay is not needed, which is why the family sells in the volumes it does.

The 150 nA supply current on a 1.2 V rail is a smaller fraction of the rail budget than the same current on a 3.3 V rail, but it is still the lowest available in this class. A part that draws 1 microamp instead would spend eight times the charge over the same period, and on a product that is asleep for months the difference decides whether the cell lasts its rated life.

What to check before a purchase order is released

  • The threshold option, because 1.1 V here and 0.9 V on the sibling option are the same body and the same price.
  • The hysteresis against the ripple on the monitored rail, since 11 mV is tight enough to follow a burst mode converter.
  • The output current at the actual rail voltage, which is 120 microamp at the bottom of the range.
  • The delay, which is fixed at 200 milliseconds and cannot be shortened with an external part.
  • The body, since the 4 pin option in this document belongs to the TPS3831 with the manual reset input.

Which projects this part fits

Low voltage core rails, single cell battery products with a 1.2 V logic rail, wearables and metering front ends are the natural cases. Any board that already uses the 0.9 V or 2.93 V member of the family and needs one more rail watched with the same current budget is the other, because the parts share a body, a pinout and a resistor free arrangement.

Questions that come up before a purchase order is released

Can this part watch a 1.8 V rail?

It can, but the 1.67 V option of the same family is the one that sits below the tolerance of a 1.8 V rail, and using this member there would assert while the rail was still good.

Does the output need a pull up?

No. The output is push pull, so it drives both directions and needs no external resistor.

What happens during a slow supply ramp?

The output stays low until the rail has passed the threshold plus the hysteresis and the 200 millisecond delay has run, which is the behaviour wanted on a board that is plugged into a slowly rising supply.

How SUPERB handles this line

Small supervisors in the 3 pin body are ordered by the reel on production and by the hundred on prototypes, and both are routine for us. Our one stop BOM sourcing covers a board where this part sits beside passives, connectors and a processor, and the kitting service is what most prototypes use when the supervisor is the only long lead line. Where a customer needs a second source for a board that is already qualified, the drop in replacement check is the first step.