Contact Us

TPS3836L30QDBVRQ1

Brand: Texas Instruments
Texas Instruments TPS3836L30QDBVRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS3836L30QDBVRQ1 — Power Management & Signal Chain | Superb Automation

TPS3836L30QDBVRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS3836L30QDBVRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS3836L30QDBVRQ1 nano power supervisor with a selectable reset delay

The TPS3836L30QDBVRQ1 watches a 3 V rail against a 2.64 V threshold and holds a processor in reset with either a 10 millisecond or a 200 millisecond delay, chosen by where the CT pin is tied. Supply current is 220 nA typical, which is low enough that the supervisor is no longer the part that decides how long a battery product can sleep.

The output is push pull and active low, so it drives a processor reset pin directly with no pull up resistor. The manual reset input carries an internal pull up and only needs a switch to ground, and the vendor asks for that pin to be tied to the supply when it is unused, because a floating manual reset input is a reset that fires at random.

Key parameters taken from the TPS383x document

Monitored rail3 V option with a 2.64 V threshold, printed as 2.56 V minimum and 2.69 V maximum, from a family that also carries 1.8 V, 2.5 V, 3.0 V at 2.79 V and 3.3 V options
Supply range1.6 V to 6 V on the supply pin, with the CT, MR and reset pins allowed up to the supply plus 0.3 V
Supply current220 nA typical, which is the figure the vendor puts in the title of the family
Reset delay5 to 15 milliseconds with CT tied to ground, 100 to 300 milliseconds with CT tied to the supply
Reset outputPush pull active low on this member, active high on the TPS3837 and open drain on the TPS3838
Hysteresis at the supply pin30 mV for a threshold between 1.7 V and 2.5 V, 40 mV for a threshold between 3.5 V and 5 V, both printed in the electrical table
Manual resetInput with an internal pull up, logic low at 0.3 times the supply, to be tied to the supply when unused
Response10 microseconds typical and 50 microseconds maximum from the supply to the reset output
Pulse width6 microseconds minimum at the supply pin for a reset to be recognised
Reset at power upOutput valid from a 1.1 V supply
ESD4000 V human body model and 1000 V charged device model
Body5 pin SOT-23 DBV, with a 6 pin WSON of 2 by 2 millimetres for the open drain member of the family
TemperatureMinus 40 to plus 85 degrees C

Two points about the string. The Q1 suffix marks the automotive qualified version, and the document attached to this page is the industrial TPS383x family revision, whose own introduction points automotive users to the separate TPS383x-Q1 file. The L30 field is the 2.64 V threshold option on a 3 V rail rather than the 2.79 V option, and those two options differ by 150 mV in the same body, so the letter after the family name is the whole difference between a board that resets at the right level and one that resets early.

Where the numbers matter in a real build

The 220 nA typical figure is the reason this family exists. A coin cell product that has to sit in standby for a decade cannot afford a supervisor that draws 15 microamp, and a part that draws a fifth of a microamp can be powered from the same rail it watches with no series switch. The trade is that a nano power comparator is slower and has less drive than a general purpose part, which is why the propagation is printed in tens of microseconds rather than in nanoseconds and why the output is meant for a reset pin rather than for a bus.

The delay choice is made on the board and not in software. Tying CT to ground gives the short delay for a processor that boots quickly, tying it to the supply gives the long delay for a regulator that needs time to settle, and the printed windows of 5 to 15 milliseconds and 100 to 300 milliseconds reflect an internal oscillator rather than a trimmed timer. A board that must guarantee 150 milliseconds of hold time has to look at the minimum of the long setting rather than at its typical value.

The 2.64 V threshold sits at 88 per cent of a 3 V rail. That is below the minus 5 per cent point of 2.85 V and well below the minus 2 per cent point, so the supervisor asserts only after the rail has left its tolerance band. On a rail that is allowed to run down slowly, the processor keeps working until the supply is close to the level where its own core stops, which is the intended behaviour and leaves very little time for a shutdown routine. Where a longer warning is needed, the manual reset input can be driven from a separate divider as a crude early warning, and the part then holds the processor in reset until the rail recovers.

What to check before a purchase order is released

  • The threshold letter, because L30 at 2.64 V and H30 at 2.79 V are both printed on a 3 V rail and are not interchangeable.
  • The automotive suffix, which is served by the TPS383x-Q1 document and is not printed in the industrial addendum attached here.
  • The output polarity, since the same family prints active low, active high and open drain in one 5 pin body and the board cannot be reworked between them.
  • The CT pin connection, because it sets the delay and a floating CT pin is not one of the two published settings.
  • The MR pin, which has to be tied to the supply when no reset button is fitted.

Which projects this part fits

Battery powered instruments, utility meters, wireless sensors and portable medical monitors are the cases the vendor lists, and the common thread is a rail that has to be supervised with almost no standing current. Automotive body and dashboard modules are the second case where the Q1 string applies, and any product that wakes on a timer, measures and goes back to sleep benefits from a supervisor that does not dominate the sleep current.

Questions that come up before a purchase order is released

Does the CT pin need a capacitor?

No. This family selects between two fixed delays by tying the pin high or low, and the capacitor setting belongs to a different family with a programmable timer.

Can the output drive a second reset input?

The push pull output sources and sinks a few milliamps, which covers one or two loads on a short net. A long net with several loads is better served by the open drain member with one pull up.

Is the 220 nA figure valid at high temperature?

The typical figure is a 25 degree number. The electrical table prints a maximum as well, and that is the figure to budget with on a product that runs warm.

How SUPERB handles this line

Nano power supervisors are ordered in small quantities for prototypes and in reels for production, and the automotive rows are usually the ones with a long allocation. Our power management cross reference covers what this part replaces on a board that currently uses a comparator and a reference, and the lead time note covers how a twelve week automotive row is handled without moving the schedule. Where a board has to change family, the drop in replacement check is what we run before a sample is offered.