TPS3828-33DBVR
Product Specifications
TPS3828-33DBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS3828-33DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS3828-33DBVR: 3.3 V voltage monitor with watchdog and open-drain reset
TPS3828-33DBVR is a supply supervisor that holds a processor in reset and also watches for a stalled program in a SOT-23 body of 5 pins. It monitors a 3.3 V rail against a fixed internal threshold, holds RESET low for 200 ms after the rail is good, and drives an open-drain output low if the watchdog input is not toggled within 1.6 s.
Order code and package
| Ordering string | TPS3828-33DBVR, DBV package, SOT-23, tape and reel |
| Threshold family | 2.5 V, 3 V, 3.3 V and 5 V options, this code is the 3.3 V member |
| Output type | Open drain, active low on the TPS3828 |
| Package | 5-pin SOT-23 |
| Ambient range | -40 C to 85 C |
| Pin count check | VDD, GND, RESET, WDI and MR, all five used in a normal circuit |
Electrical parameters that decide the application
| Reset delay | 120 ms minimum, 200 ms typical, 300 ms maximum above the threshold |
| Watchdog timeout | 1.6 s on the TPS3828, 200 ms on the TPS3820 |
| Supply current | 15 microamp typical, 25 microamp maximum, with WDI, MR and outputs unconnected |
| Threshold drift | Normalized to 0.995 through 1.001 over the full temperature range |
| Manual reset | MR input with an internal pull-up, so a switch or a host pin can pull it low |
| No external parts | The delay is internal; no timing capacitor is required |
Points to check before this part goes on a BOM
The quiescent current is the whole reason this part exists in a battery product, and the maximum column is the one to budget: 25 microamp for a year is 219 mAh, which is most of a CR2032, while the 15 microamp typical figure gives 131 mAh. A supervisor that keeps a 3.3 V rail alive in standby is therefore a visible line in the energy budget, not a rounding error.
The watchdog period of 1.6 s is generous enough that a firmware loop with a 10 ms service tick has 160 times the margin, and tight enough that a blocked task is caught within two seconds. What actually trips it is not a crash but a long blocking call, a flash erase loop or an I2C retry storm inside the same task that services the pin, so the service has to come from a path that cannot be blocked.
RESET is open drain, so the rise time is set by the pull-up and the load capacitance: 10 kohm into 100 pF is about 1 microsecond, and the same pin into 1 nF is 10 microseconds. A processor that releases from reset at 0.7 times its supply needs that edge to arrive before it starts fetching, which is why the pull-up value appears in the timing budget rather than only in the bill of materials.
The 120 to 300 ms delay window is wide on purpose and still has to cover the processor boot. If the part releases reset at 120 ms and the firmware needs 150 ms before it drives WDI, the watchdog will assert reset during every power-up, and the board will look like a dead unit on a bench supply and come up on a slow-ramp supply. The safe pattern is to service WDI from the first instruction after reset.
Threshold drift over the industrial range is under 0.6 percent, from 0.995 to 1.001 of nominal, which is small compared with the rail tolerance it is asked to watch. A 3.3 V rail at minus five percent is 3.135 V and the 3.3 V monitor threshold sits well below it, so the part does not trip on a legal rail; the tolerance that matters is the initial threshold window, not drift.
The 85 C ambient limit puts this part outside a 105 C industrial enclosure, and there is no higher grade in the same family. Products that run the board above 85 C need a different supervisor rather than a derating argument, because the threshold window and the delay are both specified to 85 C only.
The -33 suffix is the 3.3 V member of a family that also covers 2.5 V, 3 V and 5 V rails, and the members differ only in the threshold programmed inside the same five-pin package. Two suffixes look identical on a board and on a photograph, so the reel label is the only place the threshold is visible, and a mixed reel during a line change produces units that reset correctly on one rail and not on the other.
Where this order code fits
The usual fit is a microcontroller, a DSP or an FPGA rail where a defined reset during power-up and a defined response to a stalled program are both required, and the board has to stay under a microamp-level standby budget. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Obsolescence Management page.
Questions buyers ask
Is the 200 ms delay the same as the watchdog period? No. The 200 ms is the reset delay after the rail crosses the threshold, and 1.6 s is the watchdog period. Confusing the two is the most common reason a board resets repeatedly at power-up.
Can the watchdog be disabled? Not on this part. A board that does not want a watchdog should take the family member without one, because holding WDI at a fixed level on this device produces a reset every 1.6 s.
What pulls the reset line high? An external resistor to the rail the processor uses. The part only sinks current, so the high level and the rise time are entirely the board's responsibility, and the resistor has to be small enough for the edge and large enough to keep the sink current in range.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.