TPS3823-50QDBVRQ1
Product Specifications
TPS3823-50QDBVRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS3823-50QDBVRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS3823-50QDBVRQ1 5 V supervisor with a 200 millisecond reset and a 1.6 second watchdog
The TPS3823-50QDBVRQ1 watches a 5 V rail against a 4.55 V threshold, keeps the processor in reset for 200 milliseconds after the rail is good, and resets it again if the software heartbeat stops for 1.6 seconds. It shares a body, a pinout and a family table with the TPS3820 member on the 3.3 V rail, and differs in the threshold, the reset delay and the watchdog window, which is the set of numbers that has to be right on a 5 V board.
Like its 3.3 V sibling, the Q1 suffix marks the automotive qualified version while the document attached here is the industrial family revision. The thresholds and the timings are taken from that document, and the automotive packaging rows have to be confirmed against the automotive addendum.
Key parameters taken from the TPS382x document
| Monitored rail | 5 V option, nominal threshold 4.55 V, from a family that also covers 2.5 V, 3 V and 3.3 V |
| Reset delay | 200 milliseconds fixed on this member, against 25 milliseconds on the TPS3820 |
| Watchdog timeout | 1.6 seconds, against 200 milliseconds on the TPS3820, which is the reason the two members are not interchangeable on a slow task |
| Reset output | Push pull active low on the TPS3823, with an open drain variant on the TPS3828 for a shared reset bus |
| Manual reset | MR input with an internal pull up of about 90 kilohm |
| Watchdog input | WDI toggled by a falling edge, ignored while floating, so an unconnected pin never fires the watchdog |
| Supply current | 15 microamp typical and 25 microamp maximum with all pins unconnected |
| Threshold window | Negative going threshold printed as a minimum and a typical per rail option, with 4.55 V typical on this one |
| Power up | Reset asserted from a 1.1 V supply, and the output state is defined from there upwards |
| Body | 5 pin SOT-23 DBV |
| Reel and marking | 3000 pieces on a large reel on the industrial row, marking PASI on the TPS3823-50 rows of the addendum |
| Temperature | Minus 40 to plus 85 degrees C for the family, with the A grade 3.3 V member printed to 125 degrees |
The addendum carries one row that would stop a production order if it were missed. The plain TPS3823-50DBVT row is printed with a 3000 piece large reel quantity while the same body in the G4 option is marked not recommended for new builds, and the small reel rows are marked separately. That means the suffix and the option letters have to be read together before a reel size is promised to a customer.
Where the numbers matter in a real build
A 5 V rail at minus 5 per cent is 4.75 V and at minus 10 per cent is 4.5 V. The 4.55 V threshold therefore sits between the two, which means the supervisor asserts once the rail has left its own tolerance and before it has reached the level where a linear regulator starts to drop out of regulation and pass ripple. On a board fed from a 5 V backplane through a long cable, that window is where the reset is supposed to sit, and a rail that is allowed to run at 4.6 V in normal operation will reset at random.
The 1.6 second watchdog is the difference between a supervisor that watches a heartbeat and one that watches a heartbeat and a long task. A 5 V industrial controller that spends a second in a flash erase can keep the same pin toggling from a timer interrupt and stay alive, where the 200 millisecond member would reset it. The same 1.6 seconds is too long for a product that must recover from a hung task quickly, and that is the trade the two members present.
The push pull output is quoted with a low level of 0.4 V at a few milliamps and a high level that tracks the supply through an internal pull up, so it can drive a processor reset pin with no external parts. Where two devices share one reset line, the open drain member is the one to order, because two push pull outputs fighting each other on one net is a current path that no supervisor is specified for.
What to check before a purchase order is released
- The watchdog window, because 1.6 seconds here and 200 milliseconds on the TPS3820 change the software requirement rather than the board.
- The reel option, since the G4 rows of this body are marked not recommended for new builds while the plain rows are active.
- The automotive suffix, which is not in the industrial addendum and has to be confirmed against the automotive document.
- The reset output type when more than one device shares the line, where open drain with a single pull up is the safe arrangement.
- The MR pin behaviour on a board with no reset button, because the internal pull up holds it high and any external load has to be accounted for.
Which projects this part fits
5 V industrial controllers, relay and valve driver boards, and instruments that run from a 5 V backplane are the obvious cases. Automotive body modules that still run a 5 V rail are the second, where the Q1 string applies, and any board that has to survive a slow brownout without losing its stored state is the third.
Questions that come up before a purchase order is released
What happens if the watchdog pin is left unconnected?
The part generates its own internal pulses and never fires the watchdog, which is the intended way to disable the function without changing the order code.
Does the 1.6 second watchdog drift over temperature?
It comes from an internal oscillator and is specified with a window in the switching table rather than as a trimmed figure, so the software margin has to be taken from that window.
Can the 5 V member be used on a 3.3 V rail?
No. The threshold is fixed at 4.55 V, so a 3.3 V rail would sit permanently below it and the processor would never leave reset.
How SUPERB handles this line
A 5 V watchdog supervisor is a part that disappears from distribution quietly, because the boards that use it are old and the annual volume is small. Our obsolescence management note sets out how a last time buy is planned, and the drop in replacement check covers what has to match before a substitute is accepted on a qualified board. Where the shortage is immediate, the shortage recovery route is the one we run first.