Contact Us

TPS3808G30DRVR

Brand: Texas Instruments
Texas Instruments TPS3808G30DRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS3808G30DRVR — Power Management & Signal Chain | Superb Automation

TPS3808G30DRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS3808G30DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS3808G30DRVR 3 V supervisor with a programmable reset delay

The TPS3808G30DRVR monitors a 3 V rail against a 2.79 V threshold and holds a processor in reset until the rail has been above that level for a delay the board can choose. Quiescent current is 2.4 microamp typical, which is what makes the part appear on battery products where a general purpose supervisor would be the largest standing load on the rail.

The delay is set three ways from the same pin. Left open, the CT pin gives 20 milliseconds. Tied to the supply through a resistor between 40 and 200 kilohm, it gives 300 milliseconds. Fitted with a capacitor to ground of at least 100 pF, it gives any delay from 1.25 milliseconds to 10 seconds, calculated as the capacitor in nanofarad divided by 175, plus half a millisecond.

Key parameters taken from the TPS3808 document

Monitored rail3 V nominal, negative going threshold 2.79 V, from a family that covers 0.9 V to 5 V and an adjustable member down to 0.4 V
Threshold accuracy0.5 per cent typical and 1.5 per cent maximum up to a 3.3 V threshold, 1 per cent typical and 2 per cent maximum above that
Supply current2.4 microamp typical and 5 microamp maximum at 3.3 V with the reset released
Supply range1.7 V to 6.5 V from minus 40 to plus 125 degrees, and 1.65 V at the bottom from 0 to 85 degrees
Reset delay20 milliseconds with CT open, 300 milliseconds with CT tied to the supply, and 1.25 milliseconds to 10 seconds with a capacitor
Delay window12 to 28 milliseconds for the open pin and 180 to 420 milliseconds for the resistor, both printed in the switching table
OutputOpen drain active low, with a pull up from 10 kilohm to 1 megohm recommended by the vendor
Manual resetMR input with an internal pull up of 70 to 90 kilohm, logic low at 0.3 times the supply
Response20 microseconds propagation from SENSE to RESET on a 20 microsecond minimum input pulse
BodyWSON 6 pin DRV of 2 by 2 millimetres as ordered here, with a SOT-23 6 pin DBV option in the same family
Reel and marking3000 pieces on a large reel, body marking AVO on the DRV rows of the addendum
TemperatureMinus 40 to plus 125 degrees C junction

The delay accuracy is the row that decides whether a delay can be treated as a specification or as a starting point. The 20 millisecond setting is printed as 12 to 28 milliseconds, and the 300 millisecond setting as 180 to 420 milliseconds, which is a plus or minus 40 per cent window driven by the internal oscillator. A product that needs a guaranteed minimum hold time has to pick the centre value with that spread in mind, or use the capacitor setting where the spread is dominated by the capacitor tolerance instead.

Where the numbers matter in a real build

On a 3 V rail the 2.79 V threshold sits 7 per cent below nominal, so the supervisor asserts after a regulator has already left its own tolerance band and after the processor has lost the margin it needs to run. That is the intended behaviour for a unit that is allowed to run down, and it is the wrong behaviour for a rail that is expected to be reset on any excursion, which is a reason to read the threshold against the actual supply tolerance rather than against the nominal.

The 2.4 microamp typical current is measured with the reset released and the CT pin open. Connecting the CT pin to the supply through a resistor does not change the supply current, which the vendor states explicitly, and that detail matters because the resistor divider used to set the delay on some older parts does add a standing load. On a product that spends most of its life asleep, this is the reason the part survives a component cost review.

The 20 microsecond response is fast enough that a short dip on the rail does not reach the processor, and the vendor publishes a curve of transient duration against overdrive that shows how far below the threshold a dip has to go before a reset is issued. A supply that rings for a few microseconds during a load step is filtered by the combination of that curve and the 20 microsecond propagation, and a supply that stays low for a millisecond is not.

What to check before a purchase order is released

  • The body, because the DRV WSON and the DBV SOT-23 are different footprints for the same silicon and the order code carries the body rather than the datasheet.
  • The delay setting on the board, since the CT pin left floating, a resistor and a capacitor give three different delays and a capacitor below 100 pF is ignored.
  • The pull up on the reset line, which sets the rise time against the capacitance of the net and the leakage of the processor pin.
  • The MR pin when it is not used, because the internal pull up holds it high and an external divider that holds it low keeps the processor in reset.
  • The threshold option, since the same family is printed from 0.9 V to 5 V and the 2.79 V member is not interchangeable with the 3.07 V member.

Which projects this part fits

Digital signal processors, microcontrollers and field programmable gate arrays with more than one rail are the main case, and the programmable delay exists because a device that needs 200 milliseconds of hold time on one board and 1.25 milliseconds on the next is not a different part. Portable instruments are the second case, given the standing current, and mains powered control boards that want a long reset after a brownout are the third, where the capacitor setting reaches 10 seconds with a single component.

Questions that come up before a purchase order is released

Is the delay trimmed at test?

No. The delay comes from an internal oscillator, and the printed windows of 12 to 28 milliseconds and 180 to 420 milliseconds are the specified limits rather than test data.

Does the MR input need an external pull up?

No, the pin carries an internal pull up between 70 and 90 kilohm, so it can be left open on a board that never uses a manual reset button.

Can the part watch a rail above 5 V?

The supply can sit up to 6.5 V, but the monitoring range of the family stops at 5 V and the adjustable member stops at 0.4 V, so a higher rail is watched through a divider rather than directly.

How SUPERB handles this line

Supervisors in the WSON body are the parts that a prototype build orders in hundreds while the production build orders in reels, so the usual question is a partial reel with a known date code. Our power management cross reference sets out what a single chip supervisor replaces, and the lead time note covers what we do when a factory allocation pushes a four week part into twelve. Where a board is carrying a supervisor that is no longer recommended, the pin to pin cross reference is where a replacement is checked before anything is bought.