Contact Us

TPS3808G01DRVR

Brand: Texas Instruments
Texas Instruments TPS3808G01DRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS3808G01DRVR — Power Management & Signal Chain | Superb Automation

TPS3808G01DRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS3808G01DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS3808G01DRVR: a programmable delay supervisor with an adjustable threshold and 2.4 uA of quiescent current

TPS3808G01DRVR is a supply monitor that holds a processor in reset until its rail is above a threshold set by an external divider, then keeps it there for a delay set by a single capacitor in a WSON body of 6 pins. The DRV body is six pins on a 2 mm by 2 mm pad, and the G01 code means the threshold is adjustable rather than fixed, so the same part can watch any rail from 0.4 V upward with a two resistor divider.

Order code and package

Catalogue stringTPS3808G01DRVR, with G01 marking the adjustable threshold member
BodyWSON, six pins, DRV, 2.00 mm by 2.00 mm, with the SOT-23 DBV body as the alternative
Reel3000 pieces on a large tape and reel, with the G4 row on 250 pieces in a small reel
Finish and moistureNIPDAU plating, moisture level 1, 260 C, unlimited floor life
Temperatureminus 40 to 125 C junction, fully specified over that range rather than only characterised
MarkingAVW
DocumentSBVS050N, revised August 2026
Reset outputopen drain, so it needs a pull up and it can be wired to another open drain source without a fight

Electrical parameters that decide the application

Supply range1.7 V to 6.5 V on VDD, with the SENSE pin covering 0.4 V to 5 V
Adjustable threshold0.405 V on the G01 member, which is the voltage the divider has to produce at the trip point
Threshold accuracyplus or minus 0.5 per cent typical and 1.5 per cent maximum for thresholds at or below 3.3 V, widening to 2 per cent above that
Quiescent current2.4 uA typical, which is what makes the part usable on a battery rail that is monitored all the time
Delay, CT open20 ms, the default when the pin is left disconnected
Delay, CT to VDD300 ms with a resistor to VDD rather than a capacitor to ground
Delay, external capacitor1.25 ms to 10 s with a capacitor of 100 pF or more on CT, set by the capacitor value
Manual resetan MR input with a 70 to 130 kOhm internal pull up, so a push button can pull it low without an external resistor
Reset assertionRESET goes low when SENSE falls below the threshold or MR is pulled low, and stays low for the full delay after both release
Pulse width20 us minimum on SENSE and 20 us on MR, with a 150 ns propagation delay and a 20 us high to low delay
Output drive0.3 V maximum low level at 1 mA of sink current, with 300 nA of leakage when released
Input current25 nA at the SENSE pin on the adjustable member, so a high value divider does not load the rail it watches
Power upreset is defined from 1.3 V of supply, and below that the output state is not guaranteed
Temperature driftthreshold accuracy holds to 1.25 per cent over minus 40 to 85 C on the adjustable member

Fixed thresholds against the adjustable member

TPS3808G01the adjustable member, 0.405 V threshold, the part on this page
TPS3808G12fixed 1.2 V supervisory member
TPS3808G33fixed 3.3 V supervisory member, the most common choice for a digital rail
TPS3808G50fixed 5.0 V member
TPS3808G01DRVRthe WSON row at 3000 pieces, and the DBV row is the SOT-23 equivalent
The trade in the familyfixed members give a tighter threshold window and no divider, the adjustable one gives any rail at the cost of divider tolerance

Points to check before this part goes on a BOM

The G01 threshold is 0.405 V, not the 0.4 V that the family description implies. A divider built for 0.4 V puts the trip point 1.25 per cent high, which on a 1.0 V rail is 12 mV of missed margin at the bottom. This is the sort of number that gets copied from an application note for a different family and then never checked, and it shows up as a board that resets later than expected on a slow supply ramp.

The three delay options are chosen by what is connected to CT, and the open pin case is the one that surprises people. With CT floating the delay is 20 ms, with a resistor to VDD it is 300 ms, and with a capacitor to ground it runs from 1.25 ms to 10 s. A board that leaves the pin unconnected because the delay was not considered gets 20 ms, which is short for a rail that takes 40 ms to come up on a soft start.

Quiescent current of 2.4 uA is the reason this part is used on always on rails. A supervisor that draws 100 uA on a coin cell is a supervisor that empties the cell, and a supervisor that is powered down when the rail is down does not supervise anything. This one sits between the two, drawing microamps while the processor sleeps and asserting reset the moment the rail sags.

The MR input has an internal pull up of 70 to 130 kOhm, which is weak enough that a long trace to a front panel button can pick up noise. A 10 nF capacitor from MR to ground is the usual fix and costs nothing. The MR pin is also the one to use for a watchdog that has to force a reset from another device, since it does not need an external pull up resistor.

Reset is guaranteed only above 1.3 V of supply. Below that the output is undefined, which matters on a rail that collapses slowly: the RESET line can float for the last part of the collapse and a processor with a low threshold can start executing from an undefined state. Where that is unacceptable, a resistor from RESET to ground holds the line low when the supervisor is unpowered.

The open drain output is what allows the supervisor to share a reset line with a debug connector, another supervisor or a manual reset switch. The pull up has to be sized against the 0.3 V low level at 1 mA, so a 100 kOhm pull up on a 3.3 V rail draws 33 uA and sits well inside the sink capability. A 1 MOhm pull up would work electrically and would slow the edge enough to matter on a processor with a fast reset input.

Sizing the divider and the delay capacitor

The divider is two resistors and one equation. The trip point is 0.405 V at the SENSE pin, so for a 1.0 V rail the ratio is 0.405 to 1.0, and for a 3.3 V rail it is 0.405 to 3.3. The upper resistor is chosen for current, and 100 kOhm to 1 MOhm is the useful range, because the SENSE input draws only 25 nA and a high value divider costs nothing in accuracy while saving standing current.

The delay capacitor follows from the same idea. The part charges the CT pin with a fixed current and compares against a fixed voltage, so the delay is linear in capacitance from 1.25 ms upward. A 1 nF capacitor is a few milliseconds and a 100 nF capacitor is a few hundred, and the exact scale is in the switching table. Where the delay has to be precise, a capacitor with a known dielectric is worth the extra cent, since a high K ceramic drifts with temperature and voltage.

What a supervisor does that a resistor and capacitor cannot

A resistor and capacitor on a reset pin produces a delay, and it does not produce a threshold. The processor is released when the capacitor crosses its input threshold, which varies with temperature and part, and it is released even if the rail never reached its nominal value. A supervisor compares the rail against a reference, so the release happens at a defined voltage and the reset is reasserted if the rail sags later, which is the case a simple RC cannot cover at all.

The second difference is the behaviour during a brownout. A supply that dips for a few milliseconds and recovers passes through an RC without ever crossing the processor threshold, and the processor keeps running from a rail that was out of specification. The supervisor with a 20 us response and a defined hysteresis catches that dip and holds the processor in reset until the rail has been good for the full delay, which is the behaviour that keeps flash and configuration memory intact.

Where this order code fits

This is the reset supervisor on a processor, FPGA or DSP rail in a handheld instrument, a battery powered sensor, a notebook or a portable medical device, where the rail has to be proven good before code runs Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop BOM Sourcing page.

Questions buyers ask

What threshold does the G01 use? 0.405 V at the SENSE pin, with 0.5 per cent typical accuracy. A divider built for 0.400 V trips about 1.25 per cent high.

How do I get a one second delay? With a capacitor on CT. The range is 1.25 ms to 10 s, and the delay is linear in capacitance above the 100 pF minimum.

What if I leave CT open? The delay becomes 20 ms. Connecting CT to VDD through a resistor gives 300 ms instead.

Can the output drive another reset line? Yes, it is open drain. It needs a pull up, and it can be wired to any other open drain source on the same net.

Is it safe below 1.3 V? No. The output state is undefined below 1.3 V of supply, so a rail that collapses slowly needs a pull down on the reset line to hold it low.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.