TPS3803-01QDCKRQ1
Product Specifications
TPS3803-01QDCKRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS3803-01QDCKRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS3803-01QDCKRQ1: a 1.2 V adjustable threshold voltage detector in a five pin SC-70 body for automotive rails
TPS3803-01QDCKRQ1 is an automotive voltage detector with one adjustable sense input and an open-drain reset output in a SC-70 (DCK) body of 5 pins. It compares the SENSE pin against a 1.226 V internal reference, holds RESET low while the monitored rail sits below that point, and releases the output without a delay once the rail crosses back. Supply current is 3 microamp typical at 3.3 V, threshold accuracy is plus or minus 1.5 per cent, and the part works from 1.3 V up to 6 V, so the same body covers a 1.5 V, 1.8 V, 3.3 V or 5 V rail with nothing but the divider changed. It is qualified to AEC-Q100 and specified over minus 40 C to 125 C ambient.
Order code and package
| TPS3803-01QDCKRQ1 | SC-70 body of 5 pins measuring 2.00 mm by 1.25 mm, 3000 pieces on a large reel, nickel palladium gold finish, moisture level 1 at 260 C with unlimited floor life, marking AWZ, active status in the addendum dated 9 November 2025 |
| TPS3803-01QDCKRQ1.B | the second assembly row of the same string, same body, same 3000 piece reel, and the lead finish column is the one that differs between the plain and .B rows |
| TPS3803G15-Q1 | the fixed 1.4 V member, monitoring the supply pin instead of a sense pin, open-drain output, same SC-70 body, which is the part used when the rail is already fixed at 1.5 V |
| TPS3805H33-Q1 | the dual member with a fixed 3.05 V threshold on the supply and a 1.226 V adjustable sense input, push-pull output rather than open drain |
| Pin 5 | SENSE on this order code, and no internal connection on the fixed 1.5 V member, so a footprint that wires pin 5 to the rail works for one and shorts nothing on the other |
| Thermal path | 246.6 C per watt junction to ambient in the 5 pin SC-70, which is the figure that matters when the part sits on a hot board with no copper to speak of |
Electrical parameters that decide the application
| Supply voltage | 1.3 V to 6 V in the recommended table, with an absolute maximum of 7 V and the vendor note that continuous operation at 7 V should not exceed 1000 hours |
| Sense threshold | 1.200 V minimum, 1.226 V typical and 1.244 V maximum on this adjustable member, measured at 25 C junction with the divider setting the rail trip point |
| Threshold accuracy | plus or minus 1.5 per cent over the full minus 40 C to 125 C range, which is the window that a divider tolerance has to be added to |
| Hysteresis | 15 mV for thresholds between 1.2 V and 2.5 V and a wider figure between 2.5 V and 3.5 V, so the release point sits slightly above the trip point |
| Supply current | 3 microamp typical and 5 microamp maximum into the supply pin with the reset released, which is what keeps a permanent live module from draining a battery |
| Reset output | open drain, pulling to 0.3 V or below while sinking 3 mA at a 6 V supply, so the pull-up resistor and the logic rail are chosen by the board |
| Power-up behaviour | RESET is asserted from the moment the supply passes 0.8 V, which is below the 1.3 V bottom of the operating range, so the output is defined before the rail is |
| Input current | the SENSE pin draws leakage in the nanoamp region, which is why a high value divider in the megohm range can be used on a low current rail |
| Clamp current | plus or minus 10 mA on any pin outside the supply rails, which is the number that protects the part when a rail is back driven during a fault |
| ESD | plus or minus 2000 V human body model and plus or minus 1000 V charged device model, both to the automotive test standards named in the document |
| Temperature | minus 40 C to 125 C ambient over the whole electrical table rather than a commercial window with an automotive claim attached |
| Qualification | AEC-Q100 with device temperature grade 1, which is the grade that a body module, a cluster or an infotainment head unit asks for |
Members of the TPS380x-Q1 family
| TPS3803-01QDCKRQ1 | the adjustable member covered by this order code, 1.226 V reference on the sense pin, open drain output, 5 pin SC-70 |
| TPS3803G15-Q1 | the fixed 1.4 V member, monitoring the supply pin, open drain output, same body, the option for a rail that is already 1.5 V |
| TPS3805H33-Q1 | the dual member with a 3.05 V fixed threshold on the supply and a 1.226 V sense input, push pull output rather than open drain |
| Hysteresis | 15 mV between 1.2 V and 2.5 V of threshold and a wider figure above that, which is enough for a clean rail and not enough to hide a sagging one |
| Delay | none on this member, so the output follows the comparator and releases as soon as the rail crosses back |
| Pull-up rail | free to sit anywhere within the 7 V absolute maximum, which is how a 1.8 V detector drives a 3.3 V or 5 V reset line |
| Grade | AEC-Q100 with device temperature grade 1, minus 40 C to 125 C ambient over the whole table |
Points to check before this part goes on a BOM
The divider is part of the accuracy budget. The part contributes 1.5 per cent and the two resistors contribute their own tolerance on top. A pair of 1 per cent parts turns a 3.3 V rail supervision into a 2.5 per cent window, and a pair of 0.1 per cent parts is what a tight rail actually needs.
15 mV of hysteresis is small on purpose and small in practice. It is enough to stop chatter on a clean rail and not enough to hide a rail that is sagging under load. A rail that dips by 50 mV on a load step crosses the trip point and comes back, and the processor sees a reset.
There is no delay pin on this member. The output follows the comparator, so the reset release is immediate. A board that needs a fixed 200 ms hold has to add an external timer or use a supervisor with a programmable delay pin instead of this detector.
Open drain means the pull-up sets the logic level. The output can be pulled to a rail within the 7 V absolute maximum, which lets a 1.8 V detector drive a 3.3 V or 5 V reset line. Leaving the pull-up out gives a reset line that never releases and a processor that never starts.
The 7 V maximum is not a working voltage for a 12 V rail. The supply window stops at 6 V, so a 12 V rail needs a divider or a regulator in front of the part. The 1000 hour note on 7 V is a caution about a rail sitting at the top of the absolute maximum, not an invitation to run there.
Pin 5 differs between family members. On this code it is the sense input, on the fixed 1.5 V member it is unused. A single footprint that carries both parts through a build has to keep the sense trace short and leave the pad unconnected on the fixed variant.
What a detector without a delay pin is used for
A processor supervisor with a programmable delay is the usual choice when the reset has to hold for a fixed time after the rail is valid. A detector like this one is used where the processor has its own power-on reset and the external part only has to catch a rail that collapses in the field, which is the case on a cluster or a camera module supplied from a shared 3.3 V bus.
On those boards the detector sits at the far end of the rail, not at the regulator. It sees the voltage the load sees, and a divider placed there catches a connector, a fuse or a long trace dropping more than the budget allows.
Reading the automotive rows correctly
The qualification statement and the temperature range are two different lines in the document. Grade 1 covers minus 40 C to 125 C ambient, and the electrical table is specified over that window rather than over 25 C with a note. A build that quotes the part against a 105 C grade assumption is quoting a different grade.
Where this order code fits
an automotive body controller, cluster or camera module that needs a defined reset while a 1.5 V to 5 V rail is out of window Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
What rail can this part supervise? Anything from 1.3 V to 6 V through a divider, because the trip point is the 1.226 V reference rather than the supply. A 12 V rail needs the divider to bring the sense voltage into range and the supply pin fed from a 5 V or 3.3 V rail.
Is there a fixed delay after the rail comes up? No. This member has no delay pin, so the output follows the comparator and releases as soon as the sense voltage crosses the threshold plus hysteresis. A fixed hold needs another supervisor.
Does the output need a pull-up? Yes. The reset output is open drain and the pull-up may go to any rail inside the 7 V absolute maximum, which is how a 1.8 V detector drives a 3.3 V logic input.
What is the difference from the TPS3803G15-Q1? The G15 member monitors the supply pin against a fixed 1.4 V threshold and has no sense input. This order code has the adjustable sense input, so it can watch any rail with a divider.
Can the part run from a 12 V battery line directly? No. The recommended supply window stops at 6 V and the absolute maximum is 7 V with a 1000 hour caution. A 12 V line needs a divider on the sense pin and a separate 3.3 V or 5 V supply on the supply pin.
How does SUPERB handle the two assembly rows of this string? SUPERB quotes the exact ordering string, states the date code, the packing and the country of origin on the offer, and names the row the parts came from so a line that needs one lead finish does not receive the other.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.