Contact Us

TPS3801-01DCKR

Brand: Texas Instruments
Texas Instruments TPS3801-01DCKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS3801-01DCKR — Power Management & Signal Chain | Superb Automation

TPS3801-01DCKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS3801-01DCKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS3801-01DCKR: adjustable supply supervisor with a 200 ms reset delay in a 5 pin SC-70

TPS3801-01DCKR is a reset generator that compares an external divider against a 1.14 V reference and holds a processor in reset for a fixed delay in a SC-70 body of 5 pins. It watches any rail a two resistor divider can scale to 1.14 V, draws about 9 uA, and holds the reset output low for 200 ms after the sensed voltage returns above threshold. The output is push pull, so no pull up resistor is needed, and the part works from 1.8 V rails upward because the reference sits below the rails it supervises.

Order code and package

TPS3801-01DCKR5 pin SC-70 (DCK), 3000 pieces on a large reel, marking ARF
SENSE reference1.14 V typical, so the divider ratio sets the supervised level
Reset delay200 ms typical, fixed in silicon, no external capacitor
Threshold hysteresis35 mV typical on the adjustable member, which is what stops a slow rail from chattering
Reset outputpush pull, active low, driven in both directions

Electrical parameters that decide the application

Supply voltage rangethe part runs from the same rail it supervises, 1.8 V and above in practice
Supply currentabout 9 uA typical, which is why it can sit on a battery product without a switch
Supervised inputSENSE, compared against the 1.14 V reference through an external divider
Threshold accuracy2 to 2.5 per cent overall, quoted over the full temperature range
Reset delay200 ms typical from the moment SENSE passes its release threshold
Output drivepush pull, so the pin is defined high as well as low, no pull up to size
Temperature rangeminus 40 C to plus 85 C
Package5 pin SC-70, about 2 mm by 1.25 mm of board area

The three delay members and the fixed options

TPS3800100 ms delay, the short member, for processors that boot fast
TPS3801200 ms delay, the row on this page
TPS3802400 ms delay, for rails with a slow ramp or a large bulk capacitor
Adjustable rowsthe 01 suffix watches a divider against 1.14 V, which is how this part covers a 1.0 V core or a 3.6 V rail
Fixed rowsE18, J25, L30, K33, I50 and T50 watch a factory set rail directly on the VDD pin and need no divider
Reset polarityactive low on the standard rows, with the complementary output available on the triple supervisor family

Points to check before this part goes on a BOM

The reason to pick the adjustable member is that it costs one divider and covers any rail. The reason to pick a fixed member instead is accuracy at the rail: a divider made of 1 per cent resistors adds its own error on top of the 1.14 V reference, and a fixed row is trimmed at the factory. On a 1.0 V core where the whole window is 100 mV, the divider tolerance is not a rounding error, it is the decision.

The 200 ms delay starts when the sensed voltage crosses the release threshold, not when power is applied. That means the total time from power on to reset released is the ramp of the rail plus 200 ms, which is usually what a processor wants and occasionally is not. A rail that takes 300 ms to come up gives a 500 ms total, and a program that was timed against a different supervisor will notice.

The push pull output is the part that makes this supervisor easy to use and slightly risky in a mixed voltage system. It drives high as well as low, so it must not be wired to a processor whose reset pin is pulled to a different rail. The vendor specifies the output against the supply pin, and a 3.3 V supervisor driving a 1.8 V reset pin through a push pull output will push current into the processor when it is unpowered.

A 35 mV hysteresis on the sensed input is what keeps a rail that is hovering at threshold from producing a burst of resets. On a divider monitoring a 3.3 V rail, 35 mV at the sense pin is about 100 mV at the rail, which is a normal amount for a supply that is regulating badly. If a customer sees repeated resets, the first question is whether the rail is actually sagging below the threshold, not whether the supervisor is faulty.

The supply current of about 9 uA is low enough that the part can run from the rail it supervises without a switch, and that is exactly how it is normally wired. The consequence is that the supervisor draws its current from the same rail it is holding in reset, so on a rail with a very low current budget the supervisor is part of the budget, and on a rail that is being switched off the supervisor loses its supply and the output goes undefined rather than low.

The part is specified over minus 40 C to plus 85 C, which covers commercial and most industrial equipment and excludes anything under the hood. That matters when a program asks for a 125 C supervisor with the same footprint: the pinout may match and the specification does not, and a substitution on that basis is a qualification failure waiting to happen.

There is a family detail that catches people who substitute by name. The T50 row carries a 25 ms delay rather than 200 ms, and it is easy to mistake for the 5 V fixed row because both carry a 50 in the name. The delay is the first thing to confirm when a supervisor is being replaced from stock rather than from a documented alternative.

The five pin body carries no thermal pad, and at 9 uA it does not need one. What it does need is a short trace to the rail it monitors, because the SENSE input is a high impedance node that compares against a 1.14 V reference, and a long trace next to a switching node will couple noise straight into the trip point. A supervisor that resets at random on a working board is usually a routing problem rather than a failing part.

Where this order code fits

It holds a microcontroller or a DSP in reset until its rail is valid: portable instruments, battery powered meters, small motor controls and any board where a processor has to start from a known state after a brown out. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

What rail can the -01 suffix supervise? Any rail that a two resistor divider can scale to 1.14 V at the trip point. There is no factory set threshold on this row.

Is an external capacitor needed for the delay? No. The 200 ms is fixed inside the part, and adding a capacitor to the reset pin changes the edge rate rather than the delay.

Can the output drive a processor on a different rail? The push pull output is referenced to the supervisor supply, so it should not drive a pin on a lower rail. Use a part with an open drain output for a mixed voltage interface.

What is the difference between the TPS3800, 3801 and 3802? Delay only: 100 ms, 200 ms and 400 ms respectively. The rest of the specification is the same family.

How tight is the threshold? Two to two and a half per cent over temperature, before the divider tolerance is counted.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.