Contact Us

TPS37EE4554FDSKRQ1

Brand: Texas Instruments
Texas Instruments TPS37EE4554FDSKRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS37EE4554FDSKRQ1 — Power Management & Signal Chain | Superb Automation

TPS37EE4554FDSKRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS37EE4554FDSKRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS37EE4554FDSKRQ1: the automotive 65 V window detector in a 10-pin WSON

TPS37EE4554FDSKRQ1 is an automotive grade window supervisor from the TPS37-Q1 family, the part that watches a 12 V or 24 V rail for over voltage and under voltage at the same time and holds a reset output while the rail is outside the window. It carries two independent comparators, a precision reference and the resistor divider that sets both thresholds, so the board does not need external divider resistors and does not carry the leakage they bring. The body is a 10-pin WSON measuring 2.5 mm by 2.5 mm with wettable flanks, which is the package that lets an automated optical inspection step see the joint and a low resolution X-ray confirm it.

The string carries three pieces of information. The E after TPS37 is the topology letter, and in the family table E means both outputs are open drain and both are active high. The middle four digits carry the two threshold selections. The DSK tail is the WSON body and the Q1 tail is the automotive qualification. The threshold fields are read from the vendor threshold table when a quote is written rather than guessed from the string, and the trip points go on the purchase order.

The device is AEC-Q100 qualified to temperature grade 1, which is minus 40 to plus 125 degrees ambient, with human body model ESD classification level 2 and charged device model classification C7B. The numbers below come from the TPS37-Q1 data sheet and from its orderable addendum.

What the order code sits on

Functiondual channel over voltage and under voltage window detector with reset output
Supply range2.7 V to 65 V on VDD
Sense rating65 V graded SENSE and RESET pins, independent of the VDD level
Quiescent current1 microamp typical
Detection time10 microseconds
Threshold accuracy1.5 percent maximum from 2.7 V to 36 V, 1 percent maximum on the 800 mV option
Hysteresis2 percent to 13 percent in 1 percent steps, plus fixed values below 8 V
Reset delay10 nF gives 12.8 ms, 10 microfarads gives 12.8 s
Sense delay10 nF gives 1.28 ms, 10 microfarads gives 1.28 s
Manual resetCTR pin pulls the output asserted when driven low
Output topologyopen drain, active high on both channels for the E letter
PackageWSON, 10 pins, 2.5 mm by 2.5 mm, wettable flanks, non conductive centre pad
Reel3000 pieces on a large reel
Lead finishNIPDAU
Moisture levelLevel-1-260C-UNLIM, no floor life limit
Operating temperatureminus 40 to plus 125 degrees ambient
Part marking32JL

Monitoring a rail that is not the supply

The reason this family exists is that a supervisor running from the rail it watches stops working exactly when the rail collapses. The TPS37-Q1 separates VDD from SENSE, so the supply can come from a 12 V bus while the SENSE pin watches a 5 V rail through the internal divider, or watches a higher rail with an external resistor. Both pins are graded to 65 V, and the SENSE input is high impedance enough that an external divider is possible when the internal one does not give the required ratio.

The internal divider is the default because it removes two resistors and their leakage from the measurement. On a 24 V battery system the leakage of a divider built from 1 percent resistors is a few microamps that never stop, and over a parked vehicle that is part of the quiescent budget that decides whether the battery survives a month of storage. An integrated divider at 1 microamp total supply current is the answer to that budget, and the trade is that the thresholds are fixed by the order code rather than by the board.

Built in hysteresis on the SENSE pins is what keeps a rail with ripple from producing a burst of reset pulses. The percentage options run from 2 percent to 13 percent in 1 percent steps, so a 12 V rail monitored at 10 V with 5 percent hysteresis releases at 10.5 V and does not re-assert until the rail falls back below 10 V. A cold crank event on a vehicle pulls the battery rail down for tens of milliseconds, and the hysteresis plus the programmable sense delay is what lets a system ride through it rather than reset.

Delays set by two capacitors

Two pins take capacitors and both are optional. CTS sets the sense delay, which is the time the SENSE pin has to be outside the window before the device acts, and 10 nF gives 1.28 ms while 10 microfarads gives 1.28 s. CTR sets the reset delay, which is how long the reset output stays asserted after the rail returns inside the window, and 10 nF gives 12.8 ms while 10 microfarads gives 12.8 s. The ten to one ratio between the two is printed in the data sheet and it is the same ratio at every capacitor value.

On a board with a processor the reset delay is the number that has to cover the processor's own power up sequence, and the sense delay is the number that has to ignore the transients the rail produces. Both are set by capacitors with their own tolerance and their own leakage, so a 10 microfarad ceramic with a 20 percent tolerance gives a delay with a 20 percent spread, and an electrolytic in the same position gives a wider one. The data sheet works the delay from a nominal capacitance, and a build that needs a tight window uses a film or a C0G part rather than an X5R.

The manual reset input is the third function on those pins. Driving CTR low asserts the output regardless of the rail, which lets a test fixture or a service button force a reset without removing power. In a vehicle that is the function a diagnostic connector uses, and it is why the pin is brought out rather than left internal.

Thermal and board notes for a 2.5 mm body

The device dissipates almost nothing, so the thermal question is not about the supervisor but about the copper it sits on. A 65 V rail on a 2.5 mm by 2.5 mm body means the spacing between the SENSE and ground pads is the only creepage the package offers, and the data sheet notes that the central pad is non conductive precisely to keep that spacing per IEC 60664. A board that floods copper under the part for thermal reasons removes that spacing, and a conformally coated board has to be assessed for the tracking distance the coating actually provides.

The wettable flank package is an assembly decision rather than an electrical one. A conventional WSON joint is invisible from the side, so inspection relies on X-ray or on a pull test; the flank plating makes the fillet visible, and the addendum marking 32JL is small enough that a camera at production resolution can read it. A line that already has an AOI recipe for a 2 by 2 millimetre QFN can adapt it, and a line without one will spend a day writing it.

Where the part belongs in a vehicle

Telematics control units, emergency call systems, audio amplifiers, head units and clusters, sensor fusion and camera modules, and body control modules are the applications the vendor lists. The common thread is a module that has to know whether its supply is inside a window before it enables an output, and that cannot afford a supervisor which draws more than a microamp while the vehicle is parked. A camera module that boots on a rail dip and produces a corrupt frame is the failure this part is bought to prevent.

The automotive qualification is the part of the story a purchasing team checks first, and the grade 1 ambient range is the line to look for. A part qualified to grade 1 is tested from minus 40 to plus 125 degrees ambient, which covers an engine bay sensor and a head unit behind a dashboard, while a grade 3 part stops at 85 degrees and is not the same device even when the function is identical.

Second sourcing a supervisor is harder than it looks because the threshold options, the hysteresis and the output topology are all in the order code rather than in the board. When a customer sends a part number that is no longer stocked, the comparison starts from those three fields, and the workflow on our power management cross reference page lists them in the order that matters. Where the original string has already gone end of life, the obsolete part cross reference hub covers the alternative route.

Questions buyers ask before a first order

Is this part AEC-Q100 qualified? Yes, to temperature grade 1, minus 40 to plus 125 degrees ambient, with the qualification results printed in the data sheet.

Does it need external divider resistors? Not for the internal divider options. An external divider is only used when the required threshold is not one of the published ones, and the 800 mV option is the one to use in that case because it gives the lowest sense current.

What is the difference between the two output letters in the family? The letter sets the topology and the polarity: E is open drain active high on both channels, while the other letters mix open drain, push pull, active high and active low.

How long does the reset stay asserted? That is set by the capacitor on CTR, from 12.8 ms at 10 nF to 12.8 s at 10 microfarads, before the tolerance of the capacitor is counted.