TPS37042A3OFDDFRQ1
Product Specifications
TPS37042A3OFDDFRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS37042A3OFDDFRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS37042A3OFDDFRQ1 dual window supervisor for a 3.3 V rail and a 1.2 V rail
The TPS37042A3OFDDFRQ1 is a two channel member of the TPS3704x family from Texas Instruments, and its job is to hold a processor in reset until two supply rails are both inside their windows. The first channel watches 3.3 V with a 5 per cent window, the second watches 1.2 V with the same 5 per cent window, and the reset output is open drain and active low. Both thresholds come from an internal divider, so there is no external resistor pair to calculate, place and tolerate.
The last four characters of the string are the whole configuration. A3 is the fixed threshold option, O is the open drain active low output, F is a 10 ms reset delay, DDF is the 8 pin SOT-23 body, R is the large reel and Q1 is the automotive qualification. Order any other letter in that block and the part that arrives watches different rails or releases the reset at a different time, on the same footprint.
Key parameters taken from the TPS3704x document
| Channels | Two independent window supervisors in one body, with a quad and a triple option in the same family |
| Monitored rails | SENSE1 3.3 V with a 5 per cent window, SENSE2 1.2 V with a 5 per cent window |
| Threshold accuracy | 0.25 per cent typical on the comparator, with the window tolerance printed per variant in the device threshold table |
| Hysteresis | 0.75 per cent typical, built in, so a rail that sits on a threshold does not chatter the reset line |
| Reset delay | 10 ms fixed on this variant, selected by the letter F in the order code |
| Output | Open drain, active low, one pin per channel plus a combined reset |
| Supply current | 15 microamp maximum, which is the figure that matters on a rail that stays alive in standby |
| Supply and sense pins | Separate VDD and SENSEx pins, so a channel can watch a rail other than the one that powers the supervisor, or be used as a push button input |
| Temperature | Minus 40 to plus 125 degrees C ambient |
| Functional safety | Systematic capability up to SIL 3 and hardware capability up to SIL 1, with the documentation package available from the vendor |
| Package | SOT-23 8 pin, 1.6 by 2.9 millimetres, body marking A3O |
| Lifecycle | Active, production, moisture level 1 with unlimited floor life on the rows printed in this revision |
One row in the vendor addendum deserves a check before a purchase order. The threshold table lists the Q1 strings of this family, and the packaging rows printed in the same revision are the industrial ones. The suffix has to be confirmed against the drawing rather than assumed from the family table, because the automotive row carries its own qualification document.
Where the numbers matter in a real build
A 3.3 V rail at plus or minus 5 per cent is 3.135 V at the bottom, and a 1.2 V rail at minus 5 per cent is 1.14 V. The two windows are set inside those limits by the vendor intention, which means a supervisor release is a statement about the rail, not about the tolerance of the regulator. On a board where the core rail is generated from the 3.3 V rail, the sequence is decided by the two windows rather than by the enable pins, so the second rail cannot be declared good before the first one is.
The 10 ms delay is short for a processor. It is long enough for a regulator to finish its own soft start after the sense pin crosses the window, and short enough that a warm reset looks instantaneous to a user. A board that needs to hold a memory device in reset longer than the processor is better served by the variants that carry 20 ms, 35 ms or 100 ms in the same body.
The 15 microamp ceiling is the second number to plan with. On a module that sleeps for weeks, a supervisor that draws 200 microamp is a battery problem, and this family is chosen precisely because the comparator stays alive at a fraction of that. The separate VDD pin also lets the supervisor run from a always on rail while it watches a switched one, which is the arrangement most battery products end up needing.
What to check before a purchase order is released
- The threshold table row for A3, because the two channels are fixed at 3.3 V and 1.2 V and no divider can move them.
- The output polarity and type, because open drain active low needs a pull up resistor on the board and cannot drive a pin that expects a push pull high.
- The reset delay letter, since F is 10 ms and the same body carries 2 ms, 5 ms, 15 ms and 100 ms variants.
- The automotive suffix, which has to be confirmed on the addendum rather than copied from a family table.
- The pull up value against the leakage of the processor reset pin, because an open drain output with a 1 megohm pull up rises slowly on a board with capacitance.
- The sense pin leakage, because a 3.3 V rail watched through a 100 kohm divider behaves differently from a rail watched directly.
Which projects this part fits
The vendor lists factory automation, building automation, medical, motor drives, grid infrastructure, wireless infrastructure and data center equipment. The common thread is a processor with more than one supply rail and a requirement that neither rail is allowed to run outside its window unnoticed. An industrial controller with a 3.3 V input and a 1.2 V core is the simplest case, and a motor drive that has to hold its gate driver in reset while the logic rail is still coming up is the second.
Questions that come up before a purchase order is released
Can the thresholds be moved on the board?
No. The A3 option is a fixed variant with an internal divider. Moving a threshold means ordering the adjustable variant of the same family, which uses the 0.8 V reference and two external resistors.
Does a two channel part need both channels used?
No, but an unused SENSE pin should be tied to a rail that is always inside its window rather than left floating, because a floating sense input is a reset that asserts at random.
What does the reset do during power up?
The output stays low while either rail is below its window, then releases 10 ms after the last rail crosses. Below the minimum supply of the supervisor the output state is not guaranteed, which is why the pull up resistor matters on a rail that collapses slowly.
Is the same part available in a smaller body?
The TPS3704x family is printed in the DDF SOT-23 body only, so a smaller footprint means a different family rather than a different order code.
How SUPERB handles this line
Supervisors are the parts that a bill of materials forgets until a field return appears, so the sourcing question is usually a reel split rather than a full reel. Our power management cross reference lists what a single chip supervisor replaces in discrete parts, and the incoming inspection plan covers what we check on a mixed analogue reel before it goes to the line. When a running board loses its vendor part, the obsolete part cross reference hub is the first stop.