TPS3703C7500DSERQ1
Product Specifications
TPS3703C7500DSERQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS3703C7500DSERQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS3703C7500DSERQ1 5 V automotive window reset IC with a 7 per cent window
The TPS3703C7500DSERQ1 watches a 5 V rail with a plus or minus 7 per cent window and a shorter delay option than the A suffix members. The C is 5 ms with the CT pin open and 100 ms with CT tied to the supply. The 7 is the window, the 500 is the 5.00 V rail, and the Q1 at the end is the automotive qualification. It is the member of the family that suits a 5 V sensor or actuator rail in a vehicle module, where the rail is allowed to move further than a processor core but still has to be watched in both directions.
One thing has to be said plainly, because it affects ordering. The document staged for this page is the industrial TPS3703 data sheet, revision SBVS249B, and its orderable addendum does not print the C7500DSERQ1 string. The automotive members are covered by a separate document. The decoding above follows the family nomenclature in the industrial document, which defines the delay letter, the window digit, the rail digits and the body, and the Q1 suffix follows the usual automotive convention. Anyone releasing this string against a production order should confirm it against the automotive addendum before the purchase order goes out.
Key parameters taken from the TPS3703 document
| Monitored rail | 5.00 V nominal with a plus or minus 7 per cent window, so 4.65 V and 5.35 V |
| Supply range | 1.7 V to 5.5 V, which means the part is powered from the rail it watches or from a lower rail |
| Threshold accuracy | 0.25 per cent typical and 0.7 per cent over temperature, so the window is the only wide tolerance in the chain |
| Delay | 5 ms with CT open and 100 ms with CT tied to the supply, both shorter than the A suffix members |
| Quiescent current | 4.5 microamp typical and 7 microamp maximum |
| Outputs | Open drain active low RESET plus a second reset output for a latched indication |
| Manual reset | MR pin, active low |
| Glitch immunity | Internal filter and hysteresis |
| Temperature | The industrial document specifies minus 40 C to 125 C, and the automotive grade carries its own qualification |
| Package | WSON-6, body 1.5 mm by 1.5 mm, reel letter R |
| Order code note | The Q1 automotive document has to confirm this exact string, since the industrial addendum does not list it |
The 7 per cent window is the widest in the family, and it is the right choice for a sensor rail that is fed from a protected 5 V supply with a series diode. The diode drop alone is 0.4 V to 0.7 V, which a 5 per cent window would treat as a fault.
Where the numbers matter in a real build
The first point is the supply. The part is rated to 5.5 V on the supply pin and to the same on SENSE, so a 5 V rail with a load dump clamp behind it needs the clamp to hold below 5.5 V or the sense pin needs a divider. On an automotive board that is the difference between a working part and a returned module, because the rail can sit above 5 V during a jump start.
The second is the delay. Five milliseconds is short, and it is short on purpose: a sensor rail that drops in a vehicle has to be reported quickly so the controller can hold the last good value. Tying CT to the supply gives 100 ms, which suits a rail with a large decoupling bank and a slow regulator.
The third is the temperature range. The industrial document quotes minus 40 C to 125 C junction, and the automotive qualification on the Q1 suffix is a separate set of tests that includes the AEC-Q100 grades. A module that is qualified at the module level still needs the part level grade to match, and that is what the Q1 confirms.
What to check before a purchase order is released
- The exact string against the automotive addendum, because this document does not print it and a near miss is a different window or delay.
- The maximum rail voltage against the 5.5 V supply and sense rating, with the load dump clamp in the calculation.
- The delay option against the reporting requirement of the controller, since 5 ms and 100 ms serve different purposes.
- The pull up on both reset outputs, both open drain.
- Whether the rail needs a divider, because a 5 V nominal rail has very little room above 5.5 V.
- The grade and the marking on the reel label, since the window and delay codes are not visible on the body.
Which projects this part fits
The vendor lists motor drives, factory automation, home theatre, grid infrastructure and data centre equipment for the industrial members, and the automotive grade points at body control modules, sensor interfaces and actuator drivers. The 5 V rail with a 7 per cent window is the classic automotive sensor supply, where a protected rail has to stay inside a band that includes the protection diode drop.
Questions that come up before a purchase order is released
Is the Q1 part the same silicon as the industrial part?
The family is one silicon with several trimmed options. The Q1 suffix adds the automotive qualification route and its own documented rows, which is why the automotive document has to be consulted for the exact string.
Can a 5 V rail be watched from a 3.3 V supply?
No. The SENSE pin is rated to the supply range, so watching 5 V from a 3.3 V supply needs a divider. The part is made to sit on the rail it watches.
What is the widest window available?
Seven per cent is the widest row in the nomenclature table. A rail that needs more than that needs a different family or a divider.
Does the shorter delay affect the reset pulse width?
The delay sets when the reset is released after the rail is good. The time the output stays low while the rail is bad is set by the rail itself, not by the delay option.
How SUPERB handles this line
Automotive supervisors are ordered against a qualification, not just a function, and the order string is where that qualification lives. Our power management cross reference lists the window and delay codes of this family so a wrong step is visible before it reaches a purchase order, and our supplier quality audit covers how an automotive grade part is traced back to its reel. Our incoming inspection plan explains what we check on a part whose grade is printed on the label rather than on the body.