Contact Us

TPS3703A5500DSER

Brand: Texas Instruments
Texas Instruments TPS3703A5500DSER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS3703A5500DSER — Power Management & Signal Chain | Superb Automation

TPS3703A5500DSER

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS3703A5500DSER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS3703A5500DSER: window voltage supervisor, 5.0 V nominal, plus or minus 5 per cent, WSON-6

TPS3703A5500DSER is a window supervisor that monitors one rail against an upper and a lower threshold and drives two open drain outputs in a WSON body of 6 pins. The thresholds are set inside the package against a trimmed reference, so no external divider is needed and the accuracy is far better than a comparator built from 1 per cent resistors. The device watches a 5.0 V rail for both an undervoltage and an overvoltage condition, and the two open drain outputs let a system distinguish between them.

Order code and package

TPS3703A5500DSERActive, WSON-6, 3000 pieces on a large tape and reel, NIPDAU finish, MSL-2 with a one year floor life, marking JV
TPS3703A5500DSER.AActive, the same string with a material revision suffix
Nomenclature Awindow monitoring with the reset delay at 10 ms when CT is open and 200 ms when CT is tied to VDD
Nomenclature 5a window of plus or minus 5 per cent around the nominal threshold
Nomenclature 500a nominal threshold of 5.00 V, from the table of threshold options

Electrical parameters that decide the application

Input voltage1.7 V to 5.5 V on the supply pin
Monitored threshold5.00 V nominal, with the window at plus or minus 5 per cent
Threshold accuracy0.25 per cent typical, 0.7 per cent over the full temperature range
Quiescent current4.5 microamp typical, 7 microamp maximum
Reset delay10 ms with the CT pin open, 200 ms with CT tied to VDD, adjustable with a capacitor
Outputstwo open drain, active low, one for undervoltage and one for overvoltage
Manual reseta dedicated input that forces the outputs without removing the supply
Hysteresissmall and specified, so a rail sitting at the threshold does not chatter

Family variants and how they differ

A variantwindow monitoring, both thresholds active, delay 10 ms or 200 ms
F to H variantsundervoltage only, with the same delay options
Tolerance digit3 to 7, setting the window from plus or minus 3 to plus or minus 7 per cent
Threshold digits500 for 5.00 V, 330 for 3.30 V, and 50 mV steps down to 0.50 V
SENSE and VDDseparate pins, so the monitored rail and the supply of the supervisor can be different, which is what a redundant monitor needs

Points to check before this part goes on a BOM

The part number decodes to a specific function and it is easy to order the wrong one. The A in the string means a window monitor with a 10 ms reset delay when the CT pin is open. The 5 means a window of plus or minus 5 per cent, not 3 or 7. The 500 means a 5.00 V nominal threshold. A customer who needs undervoltage only, or a 3.3 V rail, needs a different string in the same body, and the difference is invisible on the reel.

Window monitoring is not the same as a reset IC. A plain supervisor pulls reset low when the rail is too low and releases it when the rail returns. This part also pulls an output low when the rail is too high, which protects a load from an overvoltage that a reset alone would not report. That matters on a board where a converter can fail with its pass element shorted.

Seven microamp maximum is the number for a sleep budget. The typical is 4.5 microamp, and the maximum over temperature is what a battery product has to budget against. A monitor that stays powered while the rest of the board sleeps is the only load left, and a few microamp over ten years is a real fraction of a coin cell.

Zero point two five per cent typical is tighter than most rails. The thresholds are trimmed at test, so the accuracy is in the reference and not in a divider. That is what allows a plus or minus 5 per cent window to be meaningful: if the threshold itself moved by 2 per cent, a 5 per cent window would be a 3 per cent window on one side.

The separate SENSE pin is the redundancy feature. The supervisor can be powered from a rail that is always present and monitor a rail that is not, or the other way round. On a safety related board that separation is what makes the monitor independent of the thing it monitors, and it is why the pin exists.

The reset delay is set by the CT pin, and the two fixed options are far apart. Open gives 10 ms and tied to the supply gives 200 ms, with a capacitor in between setting anything in the range. Ten milliseconds suits a processor that needs a short reset; 200 ms suits a rail that takes a long time to settle. A capacitor on the pin is the only way to get something in between.

The manual reset input is not a power on reset. It forces the outputs low while the rest of the monitor keeps running, which is how a test fixture or a front panel button resets a system without cycling the supply. It has its own propagation delay, in the region of a few hundred nanoseconds, so it is not a way to debounce a mechanical switch.

A one point five millimetre package has almost no thermal mass. That is fine because the part dissipates microwatts, but it does mean the solder joints are the only mechanical connection and the package is easy to damage with a probe. Repair work on a board with this part needs a fine tip and a steady hand, or the board is scrap.

MSL-2 with one year floor life applies. A 1.5 mm body on a 3000 piece reel is normally consumed quickly, but a repair reel that has been open for months carries a moisture risk. The seal date on the bag is the field to check, not only the part number.

What to confirm before this part goes on a purchase order

Confirm three things from the ordering string: the nominal threshold, the window and the delay option. All three are encoded in the digits, and a reel of the wrong window looks identical and behaves differently.

Ask for the date code and the marking JV, and confirm the country of origin. For a rail that is monitored for safety, the traceability of the monitor itself is part of the file.

Where this order code fits

It watches a 5.0 V rail on a motor drive or a grid interface board and pulls reset if the rail leaves a five per cent window in either direction. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Does it need external resistors to set the thresholds? No. The thresholds are trimmed inside the package, which is the reason for the accuracy figure. An external divider would add its own tolerance and drift and would defeat the point of the part.

Can it monitor a rail that is different from its own supply? Yes, the SENSE pin is separate from the supply pin. That is what allows the monitor to be powered from a rail that is always on while it watches a rail that switches.

What happens if the rail sits exactly at the threshold? The specified hysteresis and the internal glitch filter stop the outputs from chattering. Without them a rail sitting on the threshold with a few millivolt of ripple would produce a continuous stream of reset pulses.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.