Contact Us

TPS3703A5180DSER

Brand: Texas Instruments
Texas Instruments TPS3703A5180DSER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS3703A5180DSER — Power Management & Signal Chain | Superb Automation

TPS3703A5180DSER

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS3703A5180DSER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS3703A5180DSER 1.8 V window reset IC with a 5 per cent window

The TPS3703A5180DSER watches a 1.8 V rail for both an undervoltage and an overvoltage condition, with the two thresholds set inside the part at plus and minus 5 per cent. No external divider is needed, which is the whole point of the family: the accuracy of the window does not depend on resistor tolerance, and the board space it takes is the 1.5 mm by 1.5 mm body plus one decoupling capacitor.

The order code decodes into four choices. The A is the delay option, 10 ms with the CT pin open and 200 ms with CT tied to the supply. The 5 is the window, 5 per cent either side. The 180 is the monitored rail, 1.80 V. The DSE is the six pin WSON body and the R is the reel. Change any one of those and the part number changes, which is why the string has to be copied rather than reconstructed.

Key parameters taken from the TPS3703 document

Monitored rail1.80 V nominal with a plus or minus 5 per cent window, so 1.71 V and 1.89 V
Supply range1.7 V to 5.5 V, with an undervoltage lockout at 1.7 V
Threshold accuracy0.25 per cent typical and 0.7 per cent over minus 40 C to 125 C
Quiescent current4.5 microamp typical and 7 microamp maximum, which is the number for a standby budget
Delay10 ms with the CT pin open, 200 ms with CT tied to the supply, and any value in between with a capacitor on CT
OutputsOpen drain active low RESET, with a separate RESET output available for a latched indication
Manual resetMR pin, active low, which forces a reset without touching the rail
Glitch filterInternal, so a short excursion on the rail does not produce a reset pulse
SENSE and VDDSeparate pins, so the part can be powered from one rail and watch another
TemperatureMinus 40 C to 125 C
PackageWSON-6, 3000 pieces on a large reel, nickel palladium gold finish, moisture level 2 with a one year floor life, marking J6

Two rows in that table are the reason the part exists. The 0.7 per cent accuracy over temperature is what allows a 5 per cent window on a core rail. The 7 microamp maximum is what allows the supervisor to stay on a rail that is otherwise switched off.

Where the numbers matter in a real build

The window width has to be set against the processor data sheet, not against the regulator. A core rail specified at 1.8 V plus or minus 5 per cent has 90 mV of room in each direction, and a monitor with a 5 per cent window that includes its own 0.7 per cent accuracy leaves less than that. The correct choice is usually one window step wider than the processor tolerance, which in this family means the 7 per cent member rather than the 5 per cent one.

The second point is the delay. Ten milliseconds is the factory default with CT open, and that is short for a rail with a large bulk capacitor that takes 20 ms to reach regulation. Tying CT to the supply gives 200 ms, which covers almost every start-up, and a capacitor on CT gives anything between the two. The delay runs from the moment the rail enters the window, not from power on.

The third is the separate SENSE pin. Powering the part from the 3.3 V rail and watching the 1.8 V rail is the arrangement the pin exists for, and it means the reset output is still valid when the monitored rail is at zero. A part wired with SENSE tied to VDD cannot do that, because the part loses its own supply at the same moment.

What to check before a purchase order is released

  • The window step against the processor tolerance plus the 0.7 per cent accuracy, because a monitor inside the processor window will reset a good rail.
  • The delay option against the rail's own rise time, since 10 ms is short for a large bulk capacitor.
  • The pull up on RESET, because the output is open drain and does nothing without it.
  • Whether SENSE is tied to VDD or to the monitored rail, since the two give different behaviour at power down.
  • The moisture level of 2 with a one year floor life, which is a reflow window the level 1 parts in this catalogue do not have.
  • The marking, because two parts of the same body with different windows carry different codes and only the reel label separates them.

Which projects this part fits

The vendor lists motor drives, factory automation and control, home theatre and entertainment, grid infrastructure, and data centre and enterprise computing. The pattern is a low voltage rail with a narrow tolerance that has to be supervised inside the processor's own window, where a discrete divider would eat the margin.

Questions that come up before a purchase order is released

Can the window be changed without changing the part?

No. The window is trimmed at the factory and carried in the order code. Only the delay can be changed on the board, through the CT pin.

Does the part need an external divider?

No for the fixed threshold members, which is the whole point. The adjustable members of the same family use a resistor on SENSE instead.

What happens if the monitored rail is above the supply?

The SENSE pin is rated for the same range as the supply, so a monitored rail above 5.5 V needs a divider even on a fixed threshold part. Above that the pin is outside its rating.

Is the reset output active low?

Yes, and the family also brings out a second reset for a latched indication. The two are separate pins on the same six pin body.

How SUPERB handles this line

Narrow window supervisors are bought in small quantities against a specific rail, and the most common error is a window step that is one too tight. Our power management cross reference lists the fixed threshold parts of this family beside the adjustable ones, and the drop in replacement check covers what to confirm before a different window step is accepted. Our incoming inspection plan explains how a part whose only visible difference is its marking is checked on receipt.