TPS3700DSER
Product Specifications
TPS3700DSER
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS3700DSER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS3700DSER 18 V window detector with a 400 mV reference and two open drain outputs
The TPS3700DSER is two comparators in one six pin package, both referenced to an internal 400 mV source, with one output that trips on an undervoltage condition and one that trips on an overvoltage condition. Wire the two sense pins to the same divider and the pair becomes a window detector, which is the arrangement the part was made for. Wire them to two different dividers and the same part becomes two independent monitors, which is why it appears on boards where one rail has to be watched for a rise and another for a fall.
The supply range is 1.8 V to 18 V, so the part can sit directly on a 12 V or a 15 V rail without a local regulator. The outputs are rated to 18 V and are open drain, which means they can pull a 12 V logic line or a 3.3 V processor input without a level shifter as long as the pull up goes to the right rail. The body is a six pin WSON measuring 1.5 mm by 1.5 mm, which is small enough to fit next to the divider it serves.
Key parameters taken from the TPS3700 document
| Supply range | 1.8 V to 18 V |
| Reference | 400 mV internal, trimmed, specified at 1.0 per cent over temperature and 0.25 per cent typical |
| Threshold range | Adjustable down to 400 mV at the sense pin, so any rail above that can be monitored with a divider |
| Hysteresis | 5.5 mV typical, built into both comparators, so a slow rail does not chatter the output |
| Supply current | 5.5 microamp typical, which is low enough to leave on a battery rail |
| Outputs | Two open drain outputs rated to 18 V, OUTA for undervoltage and OUTB for overvoltage |
| Output logic | OUTA is low when the sense pin is below the threshold, OUTB is low when it is above the threshold |
| Propagation | Microsecond class response, so the part reacts inside a switching cycle rather than after it |
| Temperature | Minus 40 C to 125 C junction |
| Package | WSON-6, 1.5 mm by 1.5 mm, 3000 pieces on a large reel, moisture level 1, marking 7I or BE |
| Alternative body | SOT-23-6, same silicon, DDC and DDC2 strings, 3000 on a large reel |
The 400 mV reference is the number that sets the whole divider. A 12 V rail monitored with a 30 to 1 divider puts 400 mV on the sense pin at exactly 12 V, so a 10 per cent window is a 33 to 1 divider for the high side and a 27 to 1 divider for the low side. The divider tolerance is then the accuracy of the window, not the 0.25 per cent of the reference.
Where the numbers matter in a real build
The first thing to decide is whether the two comparators share a divider or not. Shared, they form a window and a single fault moves the rail out of it in either direction. Separate, they monitor two rails and the outputs are independent. Both work, and the drawing has to say which one is intended, because the same part number covers both and the board behaves differently.
The second point is the 5.5 mV of hysteresis. On a 12 V rail with a 30 to 1 divider, 5.5 mV at the sense pin is 165 mV at the rail, which is a sensible guard band. On a 1.8 V rail with a 4.5 to 1 divider the same hysteresis is 25 mV at the rail, and a supply that recovers slowly will still cross it cleanly.
The third is the output pull up. Both outputs are open drain and both are rated to 18 V, so the pull up can go to the monitored rail itself or to a logic rail. Pulling up to the monitored rail is convenient and wrong for an undervoltage flag, because the flag loses its pull up exactly when the rail falls. The pull up belongs to a rail that stays alive.
What to check before a purchase order is released
- Whether the two comparators share one divider or serve two rails, because that decision changes the whole circuit.
- The divider ratio against the 400 mV reference, with the divider's own tolerance counted before the reference accuracy.
- The pull up rail for each output, since a flag pulled up to the monitored rail disappears when the rail does.
- The 18 V rating of the outputs against the highest voltage on the board, not against the monitored rail alone.
- The 5.5 microamp supply current against the standby budget of the product.
- The body, WSON or SOT-23-6, because the two are the same silicon on different footprints.
Which projects this part fits
The vendor lists industrial control systems, automotive systems, embedded computing modules, DSP and microcontroller applications, notebook and desktop computers, portable and battery powered products, and FPGA and ASIC applications. The pattern is a rail that has to be watched in both directions, where a simple supervisor would only catch the fall. A 12 V intermediate rail feeding a point of load converter, or a battery rail that must not be over charged, are the two most common cases.
Questions that come up before a purchase order is released
Can the part monitor a rail above 18 V?
The supply pin is limited to 18 V, so a 24 V rail needs the divider to bring the sense pin into range and a local supply for the part. The sense pins themselves see only the divided voltage.
Are the outputs push-pull?
No. Both are open drain and both need a pull up resistor. That is what allows them to be wire-ORed with other flags on the same line.
What sets the window width?
The two dividers. The part fixes the reference at 400 mV and the hysteresis at 5.5 mV, and everything else comes from the resistors on the board.
Is there a version with a fixed threshold?
Not in this family. The TPS3700 is the adjustable member, and the fixed threshold parts in the same catalogue are separate devices with their own order codes.
How SUPERB handles this line
Window detectors are usually specified late in a project, when the rail behaviour has already been measured and the window has to be tightened, which means they are often bought against a short schedule. Our power management cross reference lists this family beside the fixed threshold parts it replaces, and the lead time solutions page covers what we do when the chosen body is short. Where the divider and the detector have to arrive together, our kitting service is the route we quote.