Contact Us

TPS3307-18DR

Brand: Texas Instruments
Texas Instruments TPS3307-18DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS3307-18DR — Power Management & Signal Chain | Superb Automation

TPS3307-18DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS3307-18DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS3307-18DR: triple processor supervisor that watches 3.3 V, 1.8 V and one user set rail

TPS3307-18DR is a three input supply monitor with a fixed 200 ms reset delay, built for processors that need more than one rail to be valid before they start in a SOIC body of 8 pins. It monitors two factory set rails at 3.3 V and 1.8 V and a third input that any divider can set, and it holds the reset outputs for 200 ms after all three are above threshold. Supply current is 40 uA maximum, the part runs from 2 V to 6 V, and the reset output is defined from 1.1 V of supply.

Order code and package

TPS3307-18DR8 pin SOIC (D), 2500 pieces on a large reel, marking 30718
TPS3307-18DGN8 pin HVSSOP with thermal pad, tube of 80, same silicon and thresholds
TPS3307-18DGNRHVSSOP on a 2500 piece large reel, the smaller footprint option
SENSE1 threshold2.93 V typical for a 3.3 V rail, about 11 per cent below nominal
SENSE2 threshold1.68 V typical for a 1.8 V rail, again about 7 per cent below nominal

Electrical parameters that decide the application

Supply voltage range2 V to 6 V on the VDD pin, which is also the rail the outputs are referenced to
Supervised inputsSENSE1 factory set to 3.3 V, SENSE2 factory set to 1.8 V, SENSE3 set by an external divider
SENSE3 reference1.25 V typical, so the divider ratio sets the monitored rail
Reset delay200 ms typical, fixed, no external capacitor
Reset outputsRESET and RESET bar, complementary, both driven from the supply
Supply current40 uA maximum across the temperature range
Output validitythe reset output is defined once VDD is above 1.1 V, below that it is not guaranteed
Manual resetan active low input that forces the reset state, with an internal pull up
Temperature rangeminus 40 C to plus 85 C, narrower than the industrial parts around it

The three members and what each one watches

TPS3307-183.3 V and 1.8 V factory set, third input by divider, the row on this page
TPS3307-253.3 V and 2.5 V factory set, third input by divider, 2.25 V typical on the 2.5 V input
TPS3307-335 V and 3.3 V factory set, third input by divider, 4.55 V and 2.93 V typical
Third inputalways a comparison against 1.25 V, so the divider is what makes it a 1.2 V or a 0.9 V monitor
Hysteresiseach input has a defined release threshold above the trip point, which is why a slow rail does not chatter
Manual resetone active low pin, useful for a test point or a front panel button

Points to check before this part goes on a BOM

A triple supervisor exists because a processor with a core rail and an input and output rail can start in an order that damages it. Holding reset until all three are above threshold is the cheap half of that problem, and the part does it with one package instead of three. What it does not do is sequence the rails: it waits, it does not enable them in order.

The factory thresholds are roughly 11 per cent below nominal, 2.93 V on the 3.3 V input and 1.68 V on the 1.8 V input. That is wide enough to tolerate normal regulation and narrow enough to catch a rail that has collapsed, but it will not catch a 5 per cent droop on a rail that is otherwise alive. Programs that need a tighter window use a separate monitor on the rail that matters.

The third input is the one that gets misused. It compares against 1.25 V, so the divider sets the monitored level, and the divider current flows continuously from whatever rail is being watched. On a 1.2 V core the divider can be a real load, and on a 0.9 V rail a 10 kOhm divider is the difference between a supervisor and a drain. Size the resistors against the rail, not against the reference.

The reset output is only defined once the supply is above 1.1 V. Below that the pin is not guaranteed to be in either state, which matters on a board where the supervisor is the only thing holding a processor off during a slow brown out. In practice the processor's own power on reset covers that window, and the part is specified for what it can promise rather than what a customer might want.

The 200 ms delay is fixed and starts only after all three inputs are above threshold, so the total time from power applied to reset released is the slowest rail plus 200 ms. A program that needs a longer or shorter hold has to change family, not add a capacitor, and the same silicon is offered with 100 ms and 400 ms variants under other order codes.

The 8 pin HVSSOP version carries a thermal pad that the SOIC does not have, which matters more for board area than for dissipation: this part draws 40 uA, so it never gets warm. The reason to pick DGN is the 3 mm by 3 mm footprint, and the reason to stay with D is that the SOIC is easier to inspect and rework on a line that does not run fine pitch parts.

The temperature range stops at 85 C, which excludes the part from most automotive and industrial positions and puts it squarely in consumer and commercial equipment. That is not a defect, it is a specification, but it is the first thing to check when a customer asks for a drop in replacement from a 125 C part.

The manual reset input is often left floating on a board that does not need it, which is acceptable because the pin carries an internal pull up. It becomes useful on a bench build where a technician wants to hold the processor in reset without pulling power, and it is the cheapest place to attach a test point. On a product with a front panel button, tying the button to this pin saves a separate reset supervisor.

The two output polarities come from the same package, so a board can drive a processor that wants active low reset and a peripheral that wants active high from one part. That is unusual at this price point and it is part of why the part survives on boards that are otherwise moving to smaller supervisors. What it does not provide is a separate open drain output, both pins are driven.

Marking matters on this family because the three members are otherwise identical in the hand. The SOIC carries 30718 for the 1.8 V member, the HVSSOP carries AAP, and a mixed tray of the three cannot be told apart without reading the marking. Any incoming check on this line should compare the marking against the order code rather than trusting the reel label alone.

Where this order code fits

It sits on processor boards where a 3.3 V input and output rail and a 1.8 V core have to be valid together: industrial controllers, portable instruments, metering and the control board of a small drive. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Does this part sequence three rails? No. It monitors three rails and holds reset until all are above threshold. Sequencing, where one rail is enabled after another, needs a separate sequencer or a processor with built in sequencing.

What is the third input for? Any rail the customer wants to watch. The input compares against 1.25 V, so an external divider sets the level, and the divider current comes out of the monitored rail.

Can the 200 ms delay be changed? Not on this order code. The delay is fixed in silicon, and the family is offered with different delays under different part numbers.

What marks the part on the package? 30718 on the SOIC, AAP on the HVSSOP body. Marking is how a line tells the 1.8 V member from the 2.5 V and 5 V members, which look identical otherwise.

Is a pull up needed on the reset output? No. Both reset outputs are driven, so no external pull up is required, and the polarity is available in both directions from the same package.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.